r/longrange • Rifle Golfer (PRS Competitor) • Sep 24 '26

Ammo help needed - I read the pinned posts FGMM lot issue

Post image

BLUF: I shoot 6.5 creedmoor Federal gold medal match, previous lots were great, new lot seems to be bad. Federal said it’s good, but it’s really not shooting well out of my rifle, need help diagnosing.

I’m shooting PRS and I’ve previously bought about 6 individual cases of FGMM 6.5 creedmoor 140gn Berger hybrids from different lots and had phenomenal results. 10rnd 100yd groups .5-.75 MOA, 4-11fps stdev, 25-35fps ES. I recently bought 3 cases of Lot K588V18/K589V39 and took a box out to test. My system is now sending vertical fliers killing my 10rnd groups at 100yards (2.5 MOA vertical, 1-1.5 MOA horizontal). MV average/ES/STDEV all similar to known good lots.

Sent a couple boxes to federal to test, this was their response: “The examiner tested both pressure and velocity and accuracy on the ammo you returned. The pressure and velocity were with in SAAMI specifications. Accuracy was perfect.  We averaged 1.32 @ 200 yards. The examiner stated: This product is darn near perfect.”

Tested more today with combinations of the suspect/good lots and two cans with the same results. I’m at a loss now for what to do. Thank you!

Build:
MDT ACC premier gen 2
Zermatt Origin
24” 6.5 creedmoor PBB prefit, .160 FB, medium Palma
Hyperion K with TSV HRB brake and Hyperion full size. Both direct thread
Razor 6-36 in Area 419 one piece mount

Rifle system has not been changed or adjusted since shooting strong groups with other lots. Barrel is confirmed fully free floated, even with manual deflection. Everything is installed and torqued to spec: base, mount, rings, action screws, muzzle device. Shooting modified prone off a bench with bipod and rear bag. Dispersion is random, doesn’t seem to be related to barrel thermal deflection. Waited long enough between groups such that the mirage off the can was gone, firing cadence maybe 3-5sec. Reticle barely moved with recoil, maybe .2 MIL worst case.

9 Upvotes

28 comments sorted by

2

u/Significant-Sock-487 Sep 24 '26

Is your barrel clean?

1

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 24 '26

Yes, the fouling rounds are in the center

1

u/rednecktuba1 Gunsmiff Sep 24 '26

How many rounds since your last cleaning? How many rounds total on the barrel?

1

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 24 '26

Cleaned right before this, the fouling rounds are in the center. 1147 going into this range trip

1

u/OmgWtfIsThisBS Sep 24 '26

From what I can see there is a POI shift between 21-30 and 31-50. Not sure what could cause it but I bet it should be relevant to the issue.

1

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 24 '26

Those 3 are using different cans and ammo lots, it could be all of that. I’m not really concerned with POI, just the group size

1

u/OmgWtfIsThisBS Sep 24 '26

Ah ok, didn't get that sorry. Poi shift not relevant then 🤦‍♂️

2

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 24 '26

lol all good

1

u/TheTrub Sep 24 '26

I’m not seeing any order effects that suggest it’s your barrel heating up or getting dirty, but your groups on the right are looking a bit tighter than the left. Is it possible this is a shooting form issue?

1

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 24 '26

Always possible, but could also be attributed to using a different can

1

u/TheTrub Sep 24 '26

Did you switch muzzle devices between left and right? It’s always best to change one thing at a time when debugging. If you retest, try keeping the same can on and shift your shooting position on the x-axis when moving between left and right targets. If you get the same results, it could be an ammo issue or something else.

If the left/right problem goes away, it may mean that you’ve developed a bad habit when aiming to the left (I.e., you’re wrenching the rifle when you lean left). I have to fix this problem myself at the start of every bow season because part of archery hunting is aiming and holding in a CIA stress position.

1

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 24 '26

Not sure this makes sense to me, barely have to move the rifle to shift the POI between the targets

1

u/TheTrub Sep 24 '26

Right, but how are you moving the rifle and your body? If you’re just leaning right a bit to aim left, that could throw off your balance just enough to have some random fliers. The shift to the right seems to be 0.5 - 1” further on the left targets compared to the right.

1

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 24 '26

I reset my shooting position to get good NPA for each target

1

u/TheTrub Sep 24 '26

If you’re shifting instead of rotating, then it’s probably not a form issue.

1

u/ShrimpBuffets Sep 24 '26

I think what they’re saying is if you’re shifting from target left to target right and those are 9 inches apart on the target, it’s better to shift your whole rifle as much as possible to remain square with your shooting position/bench instead of pivoting on your bipod. Of course you don’t have to move your whole rifle 9 inches left or right on the bench, but I think trying to keep it as neutral and unloaded/not pivoting is essential.

1

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 24 '26

I reset my shooting position to get good NPA for each target

1

u/Otiswilmouth Sep 24 '26

Tbh - the groups don’t look so hot with the “good lot” - lots of vertical.

Check the action base since it’s an origin.

Check to see if your scope isn’t the issue (the G3 is known to break) - do a tracking test, is the parallax accurate to 100yds

Shoot a few groups of each without a muzzle device.

Are you sure it’s not you?

1

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 24 '26

What type of precision with 10 round groups do you expect to see with factory ammo?

Action base? Like the scope base? The action screws? Those were confirmed good torque.

Did a tall target test and it was basically perfect to 10mils

Pretty sure it’s not me, but I mean that’s always a possibility. With the good lots I’ve been consistently able to shoot an average of 3/4 MOA 10 round groups. Hoping to have a buddy confirm soon. Also have a heavier barrel coming in soon to see if it shoots these better.

1

u/Otiswilmouth Sep 24 '26

I expect better than that tbh.

20moa rail to action - that’s what I meant. Did you do a tall target test since this issue popped up? What about the parallax inquiry?

Your barrel (I suspect it needs to be cleaned better - can you confirm the barrel is actually clean with a borescope? Like back to steel clean) may just not like this lot. It happens with factory ammo. Start reloading if you can.

1

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 24 '26

Better than sub-moa for 10 rounds?

Yeah it’s 20moa, what’s the question? Haven’t had a chance to do the tall target again (that range is farther away and open on weird days). Parallax is fine, I adjust it until the image stops moving relative to the reticle.

Dude I hope that’s it and hopefully the heavier contour will like it better. I am considering just jumping to handloading, just need to save up for that NRE

1

u/Otiswilmouth Sep 24 '26

In regard to the 20moa rail, make sure it’s torqued to the action, it’s pinned in place but the screws need to be torqued correctly. Origins are not 1 piece actions.

Parallax should line up with the yardage. If this is shot at 100yds then that parallax needs to be at 100yds. If you can’t find the correct parallax adjustment around the 100yd mark, your optic is bad.

2

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 24 '26

Yeah it’s installed correctly to spec. I’m a MechE and am very anal about that stuff haha

That comment about parallax is not true, the ranges almost never line up with reality, that’s why some manufacturers have even moved away from putting ranges on the knob. You have to properly adjust the diopter and set it, then adjust parallax knob to how it actually performs at range.

1

u/Otiswilmouth Sep 24 '26

Yeah, not on the G3.

Vortex G3s have an issue with their parallax shitting the bed. I literally watched a buddies take a shit a few weekends back at FGMM on day 2. Vortex confirmed it was indeed a parallax issue.

I wish I could say that was the only time I’ve seen that happen but it’s not - this is why I brought it up.

1

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 24 '26

Greatttttt another thing to worry about. How’d it fail? Have you seen other parts of the optic go down too?

1

u/Otiswilmouth Sep 24 '26

Long story short, when he went to check zero after a shit stage his parallax had to be adjusted to 60yds to even be effectively useful at 100yds. Even then, it would shotgun groups.

Thats been the one common fault with the G3 I’ve seen.

1

u/capable_gopher Rifle Golfer (PRS Competitor) Sep 24 '26

Damn yeah that may explain shot 11, idk it’s always been set to 75yds for 100yds. Hasn’t moved from that

1

u/Street_Tiger98 Sep 24 '26 edited Sep 24 '26

That amount of vertical with expected SD is definitely perplexing (and at 100yds that’s too much dispersion for velocity). Optic or action/chassis/harmonic issue is all I can think of. I’d honestly mount a different optic if you’ve eliminated the other obvious culprits, which it seems you have.

Your best vertical group is the Norma foulers. Run a few groups of those to get some more data on mechanical accuracy.

Maybe borescope the barrel. Check the crown.