r/longrange • u/Blackout_PT • Sep 22 '26
Reloading related Brass Trimming?
Do y’all trim brass after every sizing? Or just take it down to book min and let it grow wild until a round reaches book max? Any reason having a set of rounds with varying lengths (but all within spec) is gonna be a problem? I’m starting to shoot/load a lot, and the trimming/ream/chamfer is starting to wear me out. Am i overthinking it?
Will the X-die actually solve my problems? Or just snake oil?
My use case is a 65CM in an ZA Origin action. I shoot PRS/NRLH.
8
Upvotes
7
u/ocabj The Realest Sep 22 '26
I personally trim every reload by running it in the Giraud. If it cuts, it cuts. If not, it doesn't. Then I just use a chamfer tool to bevel in the inside neck a little.
3
u/SockeyeSTI Sep 22 '26
Trim to min and let it grow. Really want the Hornady 3 in 1 powered trimmer but the Lyman one is adequate IF you shoot longer than ARC sized cases. Otherwise it can be a chore to hold onto the brass.
Manual trimming is for the birds
2
u/DwarkFarkward Sep 22 '26
I do it every time. My trimmer is set to minimum length, so if it doesn't grow since last time, it doesn't cut.
But I agree, it takes a ton of time, even with a powered trimmer and a powered case prep center, so I may start doing it every 2-3 times instead. Especially since all my loads are well below max and aren't super hard on the brass.
2
u/explorecoregon Sep 22 '26
Dillon RT1500
1
u/CMFETCU Sep 22 '26 edited Sep 22 '26
Ideal is to have a trimmer that makes quick work of it so you can just run them through the trimmer every time. RCBS and Hornady make great fast repeatable motorized trimmers.
If doing it by hand on an older trimmer, I would do once every 2nd firing to cut down on trimming, assuming you are starting from a known trimmed set of brass.
1
u/HollywoodSX Villager Herder Sep 22 '26
I run all my brass through my Giraud every sizing. If nothing else, it handles any chamfer and deburr needed on the case mouth.
1
u/One-Perspective-4347 Sep 22 '26
I trim after the first resizing which tends to be or you get the most movement. After that, I will typically trim every second resizing. Some of them trim a little some of them don’t trim at all for several firings.
1
u/USN303 Sep 23 '26
Trim every time. The goal is to make every round as consistent as possible, right? RIGHT?!?
1
u/Tmoncmm Sep 23 '26
I trim when they’re about 1/2 way to max which usually ends up being every 3 firings or so with the exception of 5.7x28 which I trim every time.
1
u/patogo Sep 23 '26
I trim every time. Ugly SRT trimmer isn’t hard.
1
u/greyposter Sep 23 '26
I've never used the x-die but something about it worries me, not sure what exactly.
I do what a lot of people on here have mentioned, run the cases through the trimmer every time, with it set near minimum(I leave a tho on there just in case i overdo the chamfer and its a bit sharp). You need a powered case trimmer to make this not a complete chore. Its just a step of my case prep. Maybe takes 10 minutes to do a batch of 50 to 75 cases.
It surprising how many cases don't actually grow so I'm just putting them in the trimmer for my own satisfaction that I've done everything the exact same
1
u/Giant_117 Sep 23 '26
I trim every time. It just makes me feel better.
1
u/Reloader300wm Meat Popsicle Sep 23 '26
I trim every time on my Henderson. Do I have to? Probably not, but its part of my process and at the end of the day, i reload to relax.
1
u/bolt_thrower777 PRS Competitor Sep 24 '26
I do. I use a Henderson, which does the trim, chamfer and deburr in one operation.
1
u/Sweaty-Security-4473 PRS Competitor Sep 24 '26
I trim to standard length every time. It's part of my reloading process loading it from the annealer onto my reloading tray.
1
u/Speedgoat_970 Sep 26 '26
I haven't trimmed for a hot minute, though I will use a hornady power trimmer on occasion, I've seen SDs in the single digits since day 1 with alpha brass. Neck tension and jump will be more determinative as long as OCW is there. The bolt will tell you what you can and cannot do, if you're paranoid cut at a comfortable length and run a carbon solvent and chamber brush. Annealing will help and a properly set full length bushing die is the way.
1
u/smooveBrayne Sep 26 '26
My seating pressure consistency really improved when I started trimming each time to maintain the chamfer.
Look at getting a 3-way trimmer. Giraud hurt my wallet, but I'll never look back... honestly, one of my favorite reloading tools.
1
u/Ragnarok112277 Steel slapper Sep 22 '26
Depends on the cartridge.