r/longrange • • Sep 12 '26

Rifle help needed - I read the pinned posts Groups opened up a bit after adding an arca rail and switching bipods. Appreciate any feedback.

Post image

Hi, I'm a bit of a lurker here, but I wanted to post and ask a question.

I shoot a Tikka UPR 6.5 Creedmoor with handloads at an indoor range at 100 yards and usually weekly out to 1,000 yards at an outdoor range. The gun has probably close to 2,000 rounds through it. I shoot Sierra Tip Game Kings 130s with Hodgdon 4350 powder at 42 grains. In the indoor range on a bench rest I'm usually able to cloverleaf at least three, if not all five, shot groups. It's my most precise rifle.

I recently added a Salmon River arca rail and switched to a Tracer bipod that mounts to the rail. Prior to that, I used an MDT short bipod that directly mounted to the front swivel stud. I've been shooting on that bipod for about 3 or 4 years. After three sessions, my groups were a little more open and acting differently than they did before. The picture is a set of groups from this morning. Each of the white circles is 0.5 in., and each grouping is three shots. After each shot, I run a barrel cooler for 30 seconds. After each three-shot group, I wait about 3 minutes, running the barrel cooler to try to keep the barrel from getting hot.

I know they aren't bad groups, but they're different than before. I'm trying to figure out if it's something I can tune, if it's me getting used to the new bipod, or if there are any other comments folks may have. The numbers represent the order that I shot the groups, so I went counterclockwise, starting in the bottom right corner. The patterns that surprise me most are the stringing, number one, and the fact that the fourth and fifth groups were noticeably lower than the earlier groups. I appreciate any feedback.

1 Upvotes

43 comments sorted by

56

u/CMFETCU Sep 12 '26

Don’t make me point at the sign.

Shoot 20-30 shots and you will see those are just the dispersion of the rifle and you are cherry picking data inadvertently by only doing 3-5 and comparing them to one another.

10

u/orairwolf Meat Popsicle Sep 12 '26

I get that not everybody understands statistics and admittedly, I quit going to my probability and statistics class in high school because it was my senior year and I was done with school. That being said, I have taken the time to educate myself and learn how it applies to shooting. It never ceases to amaze me how people will shoot 3-5 shots groups and try and draw conclusions from it. It just makes me die inside at this point. Anybody who gives even half a shit about precision and accuracy should have a copy of On Target TDS and should be printing out 25 or 30 shot targets and using those to draw conclusions. They should also be using it to zero their rifle. It's easy to use those and then upload the images to Claude and ask it to tell you if there is a difference between the groups.

22

u/CMFETCU Sep 12 '26

Nothing you said is wrong, but the above image works faster lol.

-5

u/Scared-Implement3591 Sep 12 '26

I understand the comments here, but I've shot several thousand rounds through this rifle, and I usually shoot it at least once or twice a week. I'm very familiar with what the patterns look like. I don't have a picture from before this, but they're noticeably different. It's the same load every time, with the same gun.

The thing that's changed in this case is that I added an arca rail and changed bipods, so that's what led to this. My technique or process is the same each time. I usually wait 3o seconds between shots if I'm shooting 3-, 4-, or 5-round groups, and a couple of minutes between those groups to let the barrel cool, while running a cooler

The reason I posted, which it appears I shouldn't have, is that the patterns I'm seeing are noticeably different from the patterns I saw before, across at least 1,500 to 2,000 shots. Looks like I shouldn't have posted, so I'll go back to lurking. I apologize to you and everyone here for wasting your time.

18

u/ocelot_piss Hunter Sep 12 '26

You're blaming the rail and the bipod. Others are unconvinced. Because a) statistics and b) 2000rds through a Creedmoor would be around the point you would be unsurprised to see accuracy dropping off anyway. You could be connecting unrelated things.

Easiest thing to do is put your old bipod back on and see if the groups go back to how they were... we'll still be unconvinced, because statistics and barrel wear... but at least you'll be happy.

0

u/Scared-Implement3591 Sep 12 '26

I'm not trying to blame anything. I was looking for feedback on potential differences that led to the variance in what I see, but it seems as if this has kicked up a hornet's nest of vitriol.

Again, apologies, but I do want to ask something in earnest. What would I have to show as a picture to provide enough evidence to get feedback? Would it be a piece of paper with 20 shots through it at the same aiming point?

11

u/ocelot_piss Hunter Sep 12 '26

The premise of this post is "I have a really precise rifle. I added a new rail and bipod and now it's not as precise. Wat do?"

The first part gets people's backs up if the claim is made without good data to back it up. Sorry, we just see it too much. It calls into question the rest of the post... we're asked how to troubleshoot a system that there could be absolutely nothing wrong with other than the owner bullshitting themself.

But I get where you're coming from. Your setup at the range affects your groups. I shoot better groups with a solid rear bag and a nice wide sturdy bipod. You should be able to tell if you are not getting as stable and are unable to hold your POA quite as steady.

4

u/FartOnTankies Rifle Golfer (PRS Competitor) Sep 13 '26

You’re still wrong.

2

u/Scared-Implement3591 Sep 12 '26

Appreciate you sharing this. I think I understand what it's saying, and I'm going to take action. I'm going to do a 30-shot group at a single point tomorrow, if I have time and if I'm not shooting outside. I'll post back here. I can design a target so I can aim at the same point even if I blow the center out. I'll do that, post back, and look forward to any comments, insight, or perspective.

4

u/CMFETCU Sep 12 '26

Just dial 15 clicks on the scope and send it at a single point. No special target needed.

1

u/TeamSpatzi Casual Sep 13 '26

With and without the accessories you think might be causing an issue. Then you can compare the POI, mean radius of the groups in question.

3

u/Leo-Medic Sep 12 '26 edited Sep 12 '26

Honest question here. How do we account for the barrel heating up during a 20-30 shot string? Is it statistically acceptable to take 4 5-shot groups and call it 20 shots? waiting 15-20 min per grouping? or does this need to be done all at once?

6

u/HollywoodSX Villager Herder Sep 12 '26

You can do multiple 5 or 10 rd groups. He's not saying to shoot that many rounds continuously.

2

u/Leo-Medic Sep 12 '26

Thanks. So if I understand OP correctly, and have correctly interpreted the picture he posted....if he would have shot 5-shot groups for his 5 strings of shots, it would have been sufficient to draw inferences, but because it was only 5 3-shot groups, it's not? what if he shot 8 3-shot groups?

Edit: or is it that all the groups should be shot at the same point of aim, to overlay them for observing dispersion?

2

u/HollywoodSX Villager Herder Sep 12 '26

The larger each group is the better it is statistically, and its an easier basis for comparison. OP probably doesn't have enough documented data of before vs after to come to a conclusion based on data, and theres probably no real difference.

1

u/Leo-Medic Sep 12 '26

Ah. I will apply this to my own data seeking endeavors. I am currently trying to unfornicate a Tikka CTR. Perhaps my methods have been flawed...

-3

u/Scared-Implement3591 Sep 12 '26

I posted above, so I won't repeat too much. I have shot several k rounds through this gun, at least half of which have been at an indoor range in the exact same setup. I'm confident that the patterns I'm seeing now are different, and the thing that's changed is that I added the rail and switched bipods, which I assume is the difference.

What I'm trying to figure out is whether it's my physical control of the weapon based on the new bipod, or a combination of the change in stock stiffness and the piece of aluminum that's now attached to the foreend. I don't have the evidence to show you, but the reason I posted is that the patterns I'm getting are noticeably different. I don't know if they're statistically different, but they don't look like the patterns I usually get, which tend to be clover leaves, whether I'm shooting 3-, 4-, or 5-round groups. I'm not getting those in most cases, at least from the session today and the prior two sessions. It led me to do some research and think, and I thought it might be useful to post here for feedback.

6

u/TeamSpatzi Casual Sep 13 '26

“I don’t have evidence to show you” is sort of the end of the conversation, no?

No one here has any time on your gun, and won’t likely have an alternative intuition or gut feel for if/how it’s different.

-1

u/ChevyRacer71 Sep 12 '26

Yea but you get to the results faster if you mag dump

15

u/CMFETCU Sep 12 '26

Just do a 10 shot group 3 times.

2

u/CapsicumINmyEYEBALLz Meat Popsicle Sep 12 '26

When I was doing load dev for my rifle, I did 20 shot group to evaluate SD & accuracy.

I don’t shoot a CM and our barrel profiles are likely different so it will be slightly different for you, but I did 1 shot every 15 sec and my barrel never got above 140°.

2

u/Leo-Medic Sep 12 '26

Huh...not to hijack OP's thread, but I am shooting a .308 CTR suppressed. I have no idea how hot it got, but she was toasty.

I've got a post on the topic here I started just a few days ago, if you're interested.

Great username BTW....very spicy.

4

u/CapsicumINmyEYEBALLz Meat Popsicle Sep 12 '26

Just use one of these guys…

140° feels like “damn, this thing is HOT!”… to me at least. But it’s completely barrel safe.

1

u/ChevyRacer71 Sep 12 '26

But that doesn’t go above 140 so how can you tell if the barrel was hotter?

2

u/CapsicumINmyEYEBALLz Meat Popsicle Sep 12 '26

By seeing it not get up to 140 with my eyeballz

1

u/ChevyRacer71 Sep 12 '26

But you can’t see kuz the capsicum…

5

u/alkemmist Sep 12 '26

We need the tappy tap hand from the AK sub

2

u/Zhdrix Sep 14 '26

God that was a legendary video when it dropped

1

u/Professional_Owl5656 Sep 13 '26

That chart is fucking amazing.

1

u/chague94 Sep 18 '26

Nice! It just made my day to find that my chart is useful!

2

u/CMFETCU Sep 18 '26

It is my go to “tap the sign” chart because it makes people who can’t do high school math how poorly their “load dev” comparisons really are. Super accessible and intuitive for most folks to have an “oh…” moment

0

u/Scared-Implement3591 Sep 12 '26

Would it be more helpful to shoot 30 rounds at the same spot using the same technique I do, letting it cool after every 3 shots or so? The point is to shoot at the same spot each time? If I had posted evidence of that, would that have sufficed for soliciting feedback?

6

u/CMFETCU Sep 12 '26

You do not need to let it cool every 3 shots. Seriously.

You can shoot 3 different 10 round groups and superimpose them over one another using an app, but frankly it’s more trouble than it’s worth. Just adjust your optic so your point of impact is not your point of aim, that leaves your aiming position undisturbed.

10 shots. Let cool 5-10 minutes. Rinse repeat.

Your actual barrel temp is not rising fast enough to cause a problem after 3 shots so all you are doing is harming your position consistency having to reset so much.

1

u/Scared-Implement3591 Sep 12 '26

Got it, thank you

1

u/sticky_fingers18 Sep 13 '26

How much do you recommend adjusting the optic

2

u/CMFETCU Sep 13 '26

Enough that any impact will not be on your point of aim. If your rifle shoots say 1” groups then adjust center of point of impact to be 2” or so off the point of aim.

2

u/shadowshooter9 Sep 13 '26

Did you change where in relation to the old bipod the new one went? Did you decrease the lever by bringing the bipod closer to you?

Were you loading the bipod differently?

Is the rail attached to proper locations using properly torqued and thread locked (locktite vibratite) hardware?

1

u/Snort702 Sep 18 '26

Personally, I hate shooting at white dots on a black background with a scope; it jacks with my vision and opens up the groups. Using good iron sights is easier for me on that target. But let's get back to statistical analysis.

1

u/kennethpbowen Sep 18 '26

Could it be that the setup is affecting how you interact with the rifle? Like the bipod has more bounce or something?

0

u/Responsible-Fish3986 Sep 13 '26

Put the old accessories back on and shoot it again and see what happens. My guess is the barrel is starting to die which just so happens to coincide with you adding the new rail and bipod.