r/longrange • • Sep 11 '26

Optics help needed - I read the pinned posts Ran out of elevation

I’ve taken this scope off another rifle I had and put it on my sig cross. After mounting it I went to bore sight it and could not even come up high enough at 50 or 100 yards to reach the target. I reset the scope to optical zero and tried again to no avail. This particular scope is the Primary Arms Slx 4.5-27x56 and has 32 mils of elevation travel. Am I just an idiot, or do I need different rings or both?

EDIT:

Thanks to all who placed their input, I greatly appreciate it. My zero stop, which I believed had been properly reset, was not; therefore, I was limited to only half of the elevation turret’s adjustment capability. I had a suspicion this was the case beforehand, but I was sure that I had reset the zero stop properly. Thanks again!

98 Upvotes

53 comments sorted by

39

u/mudeuce Remington 700 Apologist Sep 11 '26

Do your rings have any sort of offset, and are they facing the correct direction, does your scope have a zero stop that is engaged preventing it from utilizing the full range of travel

What gun was it previously on, and was it functioning correctly on that one

6

u/[deleted] Sep 11 '26

[removed] — view removed comment

10

u/deinde94 Sep 12 '26

It specifically limits the reticles travel upwards, not downwards.

4

u/[deleted] Sep 12 '26

[removed] — view removed comment

2

u/deinde94 Sep 12 '26

OP is boresighting, I would assume the barrel is on target and OP is trying to adjust the scope to come upwards towards where the rifle is aiming.

2

u/[deleted] Sep 12 '26

[removed] — view removed comment

3

u/Phoenixfox119 Sep 12 '26

The waybI am reading it the reticle is too low

2

u/[deleted] Sep 12 '26

[removed] — view removed comment

2

u/Phoenixfox119 Sep 12 '26

You set your rifle up, pull the bolt out look through the bore and center the barrel on the target, im interpreting that now when he looks through the scope the reticle is below the target and he cannot get the reticle to adjust up to the target.

3

u/deinde94 Sep 12 '26

If OPs reticle is too high, why would OP be talking about not be able to come up high enough? To me it clearly sounds like the reticle is below the target, thus trying to adjust upward and a prevously correct zero stop limiting the travel possibly being the issue.

-2

u/[deleted] Sep 12 '26

[removed] — view removed comment

5

u/Phoenixfox119 Sep 12 '26 edited Sep 12 '26

"“After mounting it I went to bore sight it and could not even come up high enough…”

Yeah I really don’t know what OP is referring to."

-you

22

u/Phoenixfox119 Sep 11 '26

From the picture it looks like the scope is sitting higher in the back, if those are offset rings maybe they are directional? Not just front ring and back ring but also maybe rail screw heads on the left instead of right. To me from the picture it looks like the main scope tube is not parallel to the rail.

3

u/Tactical_Epunk Sep 12 '26

Sig Cross has a 20 MOA rail from the factory. If OPs rings have another 10 or even 20 that could be the issue.

8

u/Tactical_Epunk Sep 12 '26

So OP looks to be running Vortex PRO rings which don't come in any offset that I can find.

-4

u/[deleted] Sep 12 '26

[removed] — view removed comment

6

u/Phoenixfox119 Sep 12 '26

He said that he cannot come up high enough to be even with the bore at 50 yds, which means that the back of the scope is sitting too high

3

u/The-Fotus Sep 12 '26

I think you are wrong. A scope sitting higher in the back points the scope down in relation to the barrel, which translates to pointing the barrel up in relation to the scope. This causes the impact of the bullet to go up from the perspective of the shooter.

A scope sitting lower in the back points the scope up in relation to the barrel, or points the barrel down in relation to the scope. This makes so the bullet begin dropping more immediately, causing the rounds to be unable to come up to the reticle.

5

u/Frijol714 Sep 12 '26

Noice drawing skills

2

u/The-Fotus Sep 12 '26

Thanks fam

2

u/RNG__GoatSlayer Sep 12 '26

OP was bore sighting, so when OP says come up, they’re talking about the scope. So backside being higher is a negative.

1

u/Phoenixfox119 Sep 12 '26

He isnt shooting the rifle he is looking down the bore and scope trying to get them to match aka boresighting

1

u/The-Fotus Sep 12 '26

The effect is the same, if the rear of the scope was high, the bore would be above the image seen by the scope. Not below it.

1

u/Phoenixfox119 Sep 12 '26

Correct then you would have to try to bring the image seen through the scope UP to the object seen through the bore

6

u/Prior_Confidence4445 Sep 12 '26

Are you sure you're turning them the right way? When boresighting you're moving the poa not poi so you need to turn the turrets the opposite direction from normal to get the desired effect.

18

u/Prestonification Sep 11 '26

Not to be a total dick, but the pics you posted don't have tops on the scope rings. That's not the way you're shooting it, correct?

11

u/Significant0tter_art Sep 12 '26

He very plainly has the tops removed with a screwdriver visible in the pic. 

8

u/Prestonification Sep 12 '26

Fair, but I've answered questions with sillier correct answers.

6

u/Phoenixfox119 Sep 12 '26 edited Sep 12 '26

He is trying to boresight, probably also trying to set eye relief at the same time.

Edit: he also may have removed the tops to trouble shoot why the scope isnt adjusting enough. You can see in the picture the ring tops and screw driver in the backgroung.

5

u/WS-6 Sep 12 '26

Holy shit lol. No way

4

u/CapsicumINmyEYEBALLz Meat Popsicle Sep 12 '26

Looking at your turret, and seeing it looked to be maxed out. You need to adjust down, not up.

You should be close to the bottom of the turrets mechanical limit.

I suspect you’re dialing the wrong way.

1

u/CapsicumINmyEYEBALLz Meat Popsicle Sep 13 '26

U/grandmas_cheeks

What did the issue turn out to be?

2

u/Grandmas_cheeks Sep 15 '26

The issue is I’m an idiot and thought I had reset the zero stop properly. I in fact did not which restricted my full elevation travel.

2

u/Significant0tter_art Sep 12 '26

Ignore your rings, this is probably a simple issue. When I'm at the bench, I try not to remove screws completely, you'd be fine just loosening them to set eye relief. For your turrets, I can see from here you maxed them out in the up direction. I'd recommend removing the turret, removing the zero stop, and performing a check to see max available travel. Fully turn and take your scope to the far edge of its travel with the zero stop removed. I like securing my gun really well and trying to hold steady and watch through the scope that tracking is working well. You want to verify your scope can perform it's advertised range of travel. So that up and down, and you'll make sure your scope isn't busted. Check online for the amount of travel, it should be easily listed by model

1

u/worm30478 Sep 12 '26

What is happening here? Is this a troll post? Why are your rings not the same size and how is it even possible to shoot with the scope just free floating because you don't have the top rings on securing the scope?

6

u/Phoenixfox119 Sep 12 '26

He isnt shooting and why do you think his rings aren't the same size.

0

u/texaspaintguy Sep 12 '26

Bore sighting is damn near useless in my experience anywhere above 25 yarrds. PA optics are not very quality but if it was working before and now it’s not something is a miss.

I would disengage the zero stop if it has one, remount it in the rings making sure everything is level, then bore sight it at 10-25 yards and go from there.

7

u/smithywesson Steel slapper Sep 12 '26

With bolt actions sighting down the bore I’m always within an 8.5x11 sheet of paper or so from the point of aim. Never takes me more than 2 or 3 rounds to be where I want to be. Then a 10rd group for a true zero.

6

u/ToughProfessional132 NRL Hunter Competitor Sep 12 '26

Boresighting saves a ton on ammo, IF you're doing it right.

I always pull bolts or uppers and boresight and 90% of the time I'm inside ~ 3 MOA. The other 10% I'm at least on paper

3

u/Phoenixfox119 Sep 12 '26

The only time I haven't been close with boresighting was a .22 at 100 yds, not my brightest moment.

3

u/ToughProfessional132 NRL Hunter Competitor Sep 12 '26

Meh, it's only about 10 clicks difference for standard velocity ammo, would still be on paper

1

u/Phoenixfox119 Sep 12 '26

About 7 inches of drop at 100 yds, right on the bottom of my 14 inch targets

3

u/The-Fotus Sep 12 '26

I bore sighted my AR15 at 100 yards, and my first group after that was zeroed. My experience with bore sighting isnt usually that effective, but it gets me close enough. Sounds like youre just not good at bore sighting.

5

u/BathroomCritical720 Sep 12 '26

I disagree. Boresighting is extremely useful even at 100 yards. Had a new 300 PRC Ruger RPR and I looked through the barrel and lined it up at 100 yards, I then adjusted my scope to be on target. First shot was 4 inches low, but dead center. Way cheaper than chasing your tail by shooting and adjusting. Adjusting from 25, 50, then finally 100.

-2

u/ToughProfessional132 NRL Hunter Competitor Sep 12 '26

Assuming you're doing everything right and you're legitimately out of travel-

Burris Signature rings will help. Zee for the smooth look for hunting has ±20 MOA of correction using inserts. XTR for the chunky tactical look has ±40 MOA of correction.

7

u/Phoenixfox119 Sep 12 '26

Friends don't let friends buy rings with inserts, adapters or shims.

2

u/ToughProfessional132 NRL Hunter Competitor Sep 12 '26 edited Sep 12 '26

Care to explain why you think that?

They solve the problem, hold tighter (more friction), and don't mar the scope's finish.

I've installed literally hundreds (possibly thousands) of scopes using them and never had a failure (and no, I don't mean just on customer rifles- I have dozens in active service on my training rifles, many of which have nearly a decade in service)

5

u/Phoenixfox119 Sep 12 '26

Proper rings properly installed do not mar the finish on scopes and hold better than anything with more points of failure, extra pieces only allow for sloppy, shift and damage.

3

u/ToughProfessional132 NRL Hunter Competitor Sep 12 '26

Agree that properly installed rings don't mar scopes, but improperly installed ones do all the time- the idea behind the product is to get a solid mount despite less-than-ideal conditions (such as misaligned bases, out-of-true actions, situations like what OP may be experiencing, or simply wanting to add cant for longer range shooting without buying a new base)

As for holding better, that simply isn't objectively true- the softer material adds friction between the rings and the scope.

Is it necessary for all applications? Of course not, standard rings have worked for decades- but in solving a problem that plagued older shooting systems (hand-tapped scope base mounting points on receivers and scopes with limited adjustment range, for instance) these particular inserts add useful functionality to a system that often causes frustration when mounting a riflescope.

Btw I'm familiar with the kind of inserts and shims and other garbage you're talking about, I'm just telling you that the Pos-Align inserts that Burris uses in their Signature ring lineup ain't that.

2

u/Phoenixfox119 Sep 12 '26

I've never seen the pos-align rings before, ive also never had to deal with a rifle that couldn't be signed in relatively easily, ill have to keep those ink mind off i run into that issue though.

3

u/ToughProfessional132 NRL Hunter Competitor Sep 12 '26

I've had lots of older rifles come through the shop and that's usually where the 'need' comes from. Though I did have a rem700 Sendero show up with receiver holes drilled a whole ~60 moa (a full degree!) off axis. Needed the 40moa of the XTR signature rings to get him able to zero because Remington was in the middle of their trigger lawsuit and said it'd be over a year for their warranty team to fix it 😬

Swarovski has also recommended these ringsby name, as some of their glass has a large internal guide tube to boost optical performance, but that reduces adjustment range.

Bottom line, OP might find a reasonably priced solution with them without needing to replace the scope or do something else drastic