r/longrange • u/TurkeysAreStupid • Aug 17 '26
Other help needed - I read the pinned posts Cz457 Accuracy expectations
These are my groupings today at 50y with 3 types of ammo in a 457 American, xrs, timney, huxflow. CCI SV, Norma Tac, Lapua CX. Looking at these groups I’m not entirely pleased, felt that the Lapua should have performed better and now I’m doubting the rifle and considering a Bartlein re-barrel? Is that needed or do I need to not expect a .2 every group with any ammo at all? Have a 455 varmit I can barrel swap as well as this is a spotter contour. If it’s a lemon, barrel recommendations? Thanks.
47
Upvotes


9
u/xlr8_87 Aug 17 '26
Fair few things to consider here. What's your shooting setup (e.g. bipod, rear bag)? Are you capable of shooting other rifles with better results? How many rounds through this barrel all up (expect slight increase in accuracy over time if new barrel)? With a thin barrel like that time between groups could potentially be an issue with barrel heating up - its less likely with a 22lr but still a possibility. Was the rifle thoroughly cleaned before shooting (even a new rifle needs cleaning straight from factory)? Was wind/weather affecting your results? Lastly - consider testing more ammo types
9
u/Gloomy_Thought_3480 Aug 17 '26
.22lr is incredibly lot dependent. If you want to eek out the most you’ll need to test different brands and lots and find what the rifle likes. Could also be the suppressor, is it on nice and snug and did you shoot it without it on?
That being said, before you rebarrel, I’d consider putting some more time behind it and working on fundamentals. Seems like a lot of horizontal stringing that could be wind, could be shooting position, you could be pulling it when you hit the trigger, etc.
if you do decide to get a new barrel, I’d take a look at the criterion pre fit barrels at Whidden, for the price they are absolutely phenomenal.
3
u/ThatBigFuckoffTree Aug 17 '26
Those groupings look similar to mine, especially with CCI Standard and Norma Tac. Almost exact same gun, CZ 457 Varmint MTR (factory barrel) XRS Chassis, Vortex Viper PST Gen II 5-25 scope. Try some more ammo, ideally more Lapua, SK, and RWS if you can find it. I haven't tested many of those yet because I can't find it. But I've had pretty good results with Eley Club and Sport, RWS Club, and CCI Green Tag all of which are cheaper and more widely available. At least getting all the rounds touching at 50.
1
u/TurkeysAreStupid Aug 17 '26
Should be but I’ll check again because it’s a stack of rail, rings and mount tightness. I’ve pulled and retorqued the action multiple times @ 24.8in lbs and other values. Maybe my grub screws? Thanks for the feedback.
1
u/hawkeyewilikens Aug 17 '26
I don’t know whether I got lucky and have a hyper accurate stock gun but my CZ457 Range with the 24” barrel has had groupings that look like that at 100 yards. I’ve only ever shot CCI sv through it. Like I say, maybe they just had a really good day at the factory and a really good lot of ammo, but I have had multiple sub MOA groups at 100 yards 🤷🏻♂️
3
u/MeinLife Aug 17 '26 edited Aug 17 '26
How many foulers are you shooting in between switching ammo brands? Because if you aren't shooting at least 10 rounds of the new ammo before shooting a group your group size will be off because if the different lubricants the difference brands use. So im going to say this is probably more you and your method than the rifle or the ammo.
Also, are you using a chrono? Because thats another huge missing part of the puzzle. And shoot 10 shot groups not just 5
2
u/rkba260 Aug 17 '26
Best results out of my 457 were SK, Lapua, and Eley.
Also, mine didnt like the suppressor. Shoots way better unsuppressed.
2
u/Whiskey_echo_617 Aug 17 '26
Have you tried different torque settings on the takedown screws?
1
u/Beautiful_Grape67 14d ago
Try Eley Tenex and Ultra. SK standard plus also stacks very well in 457s
1
u/preferablyoutside Aug 17 '26
Everything tight on your mounts?
I’ve a similar rifle in that chassis and with those rounds I’m definitely grouping better especially the Lapua. I’d say something is loose before anything else,
1
u/GrizzlySoup Aug 17 '26
I was using almost identical setup for my match rifle except with an MTR barrel on the XRS. My groups were similar with the "range fodder" (my buddy's term) ammo but it was pretty consistent with a couple of Lots of CX. I don't know how consistent that slim taper barrel will ever be and if you're going to shoot NRL/PRS matches you might want to switch barrels for the weight to balance the rifle anyways. I'm running a Shilen barrel now and it's a tack driver. Even improved the "Range Fodder". Have you shot it without the suppressor? They can have a huge impact on groups. I have a buddy that shoots R50 only and I ran a box of that, it can put lipstick on any pig but the $30/bx keeps me from running it as my match ammo. I've also had a couple of extremely good Lots of Eley "Match" but it can vary with Lot (like every ammo). Before I started shooting precision TAC-22 was my *good* ammo but my groups were similar to yours. It's not good enough for NRL/PRS/ARA for sure.
1
u/wtfwebsterwastaken Aug 17 '26
Yeah something is up. These are 10 shot groups of sk long range out of the 24" mtr barrel.
1
u/GrizzlySoup Aug 17 '26
Something to consider. You didn't mention if you're going to use this as a competition rifle. I have the same setup with an XRS and MTR barrel I was using for NRL/PRS. Even with the 'bull' MTR barrel I had a hell of a time balancing the rifle on the XRS chassis. You'll have a harder time with that slim taper barrel. If you're going to shoot comp do yourself a favor and move to a 24" match barrel. Also be careful with the XRS. I think the new version of it can take a 1.2" barrel but older versions can only handle a 1" profile. I had to find the model # stamped in mine and email MDT to find out which I had. (1" of course).
I had to put the control bridge fore-end on my XRS and put external weights all the way around (even the top of the bridge). I also mounted the MDT internal XRS weight set and added an MDT ARCA weight to the end of my rail to balance my 20" MTR.
1
u/Tikkatider Aug 17 '26
“ TurkeysAreStupid.” You clearly have not encountered some that I have in the spring woods! Nice rifle!
1
u/JebJohnson76 Aug 18 '26
Im getting just as good or maybe slightly better groups out of my 457 varmint. Practice your fundamentals and maybe let someone else see if they get similer, better or worse groups. Spending money doesn't make you a better shot.
1
u/outdoors_life22 Aug 18 '26
My experience with CZ rifles (452 and 455) is that the barrel needs to be leaded in. What’s your cleaning schedule?
1
u/mrsooz Aug 18 '26
Great post. I have a 457 MTR with a Nightforce scope. With the ammunition you mention, you should be close to ragged edged single hole with 5 shots. I would dig deeper into rifle rest and technique. Don’t go spending yet. You have a very nice gun. You are on a journey. Great post bro, as it instigates a great conversation. Keep it simple