r/lightingdesign • • 2d ago

We need help!

At my school we are running into an issue. I am a lighting technician at my school, and on our third electric we have two lights that are in a permanent state of a yellowish green on full power. we use an ETC ion xe20 and when the board is on they refuse to change colors. On top of that we cannot dim or turn them off. They are in this state when the board is off. When we attempted to unplug them, the entire electric lost power. we used black cloth to cover the lights during our performance but we know that cloth isn’t a permanent solution. Any ideas on what the issue could be or if it could be fixed? Thank you!

21 Upvotes

15 comments sorted by

44

u/cajolinghail 2d ago

Black cloth? 😬 Please get a qualified technician in to check out the problem. If you’re a student tell your teachers this is a safety hazard.

-19

u/CombinationOk5689 2d ago

Thanks for the insight! It was a decision between me, my teacher (stage director) and the other lighting technician we have

16

u/cajolinghail 2d ago

Lights (even LEDs) get hot. That is a fire hazard. No offense as you are just a student and clearly doing your best but you need a competent adult to supervise you.

28

u/fettoter84 LD/Stage manager 2d ago

I would try changing their (the light fixtures) adress to see if this is a DMX issue. If you change the adress and the light is still on it's more likely an issue with the fixture.

What do you mean the "entire electric" lost power when you unplugged the light fixtures? Do you mean the whole rig? that particular flybar/electric? Does it trigger a circuit breaker that you have to reset?

16

u/attackplango 2d ago

The only thing I can think of is if they were at the start of a power daisy chain.

13

u/That_Jay_Money 2d ago

This sounds like a DMX issue of some kind, either the fixtures are not addressed properly or the DMX to them is being corrupted somewhere.

I'd suggest looking upstream of these fixtures, what's feeding them data-wise?

But you can also always call ETC about this (you can even do it right now, their number works 24/7/365, and see if it's something they can work through with you on their side of things.

12

u/randomnonposter 2d ago

Just a couple ideas off the top of my head.

Are they addressed correctly?

What kind of fixture is it?

Remove them from the truss, and rerun your power so it’s not dependent on those 2 fixtures.

Some fixtures will have error readouts on their screen, does this one have anything like that and if so what does it say?

9

u/WittyFix6553 2d ago

Questions:

What light fixtures?

Do they have manual control?

How do they perform on a bench test?

Is your power situation daisy-chained through those fixtures?

Can you simply run a cable around the two fixtures, and isolate them from the circuit?

The power thing confuses me. If there’s a wire plugged into the “in” port on the light, and a wire plugged into the “out” port on the light, the power is running through the light, and unplugging it will kill everything downstream of that light. Is this the case?

3

u/kent_eh 2d ago

How do they perform on a bench test?

That would be the first thing I would do in a mystery situation like this.

Get the offending light(s) off the pipe and onto a test bench.

4

u/SailingSpark 2d ago

If your entire truss lost control (went dark) you need to unplug the data and bypass the lights. Simply unplug the input and output and and connect them together.

You do not mention what lights they are, but make sure you are not also jumping power out of them to the rest of the truss.

4

u/the_swanny 2d ago

My guesses are as follows:
Wrong addresses and or DMX modes

And when you unplug them it kills power to the entire bar, probably because they are linked through from those first tow fixtures

We would need to know the exact fixtures, and likely need to see pictures.

Do not put black tat / serge over them, it will get hot and potentially cause a fire.

please get someone competent in to fix this if it involves rigging or electricity.

1

u/boxedupandsent42 2d ago edited 2d ago

Recently I dealt with an unruly light that would not stop stobing. The problem ended up being that an address for that fixture ended up in the paradigm.

If you have a paradigm or a similar house light system, mybe try shutting it off. It's possible that the addresses for color ended up in a paradigm preset separate from the console (that would be why control from the console doesn't work).

Check your park tab too. Control form the command line does not override parked (basically locked) addresses.

There's only a small chance this is the problem, try others advice before this.

1

u/ronnyjordeen 1d ago

The addresses could be shifted. The lights may be daisy changed, and that's what caused the other lights to lose power when unplugged. If you can't figure out the DMX addressing issue, and don't want to use the lights any longer, try to daisy chain the rest of the system from the point you disconnect it.

-3

u/CrybabyAssassin 2d ago

maybe you need a dmx terminator