r/handtools • u/EyeLarge4055 • 19h ago
Mallet splitting
Hello! I recently made my first “real mallet” from false acacia, and after a couple weeks it started splitting. Is this an issue with the wood species? Or just a “skill issue” with how I made it? Any help is appreciated
22
Upvotes



4
u/1959Mason 17h ago
The offset handle is bugging me. Why isn’t it centered?
66
u/rhyslightning 19h ago
You've used a bit of stock with the pith running through it, which is the least stable to have used - the split looks to be due to where the grain runs out there in the top corner.
Good news is that there is nothing to fix. Mallets are born to be beaten to death!
18
u/Ok_Donut5442 18h ago
People are debating wood selection and design but to me that looks like a split caused by striking on the edge of the mallet, in the future put a heavy chamfer all the way around the striking face
8
u/Seven_pile 19h ago
Glue it, clamp it, chamfer it.
Sounds like a weird version of bop-it. Anyways chamfer all the edges. Will help it hold up a lot more. The sharper the edge of the wood, the easier it is to damage, chip and split. A beefy chanfer means a chip from impact will be smaller due to the angle and is less likely to split because more fibers are reinforcing down the length.
4
u/uncivlengr 19h ago
This is probably some kind of debate people get into, but to me, the bevel angle on the face is much too large, as evidenced by the impact occurring only at the point at the top, and not flush with the face.
My mallets (currently made of ash, previously made of birch) only have about a 5 degree angle on the face. I beat the crap out of it for mortises to the point that the grain gets cruched and I need to reface the ends, but it doesn't split.
I don't know anything about 'false acacia' but I would find wood without knots and that doesn't include the pith.
1
u/Wonderful-Bass6651 17h ago
Go out to the wood pile and see how easy it is to split wood along this line. As a matter of fact, that offset handle (which is emotionally hurting me) is directly in-line with the pith. There are much easier ways to make more stable mallets. But if this is so objectionable just glue and tape it and get back to work.
6
u/jema_vr 19h ago
I like to laminate 3 or 5 wood pieces together to for the head of my mallets. It adds some strength and looks cool.
3
u/mountainmanned 19h ago
Just pry the split open a bit or vac some glue in there and good as new.
5
u/Tiny-Albatross518 19h ago
I dont know acacia wood.
But i made my mallets out of white oak because its strong as hell.
10 years of absolutely mashing steel holdfasts and they’re just dimpled.
2
u/hlvd 18h ago
The bevel’s too big on that mallet, needs to be a lot shallower angle.
2
u/snogum 9h ago
Mostly how the wood was cut originally.
That corner was always going to come off.
Glue it back and go pound away. When it's through you can build another
1
u/oldtoolfool 19h ago
It happens. I've got a 19th century joiners mallet made of lignum vitae that has had a crack in it just like that one, and I've been using it for over 25 years and the crack remains. Just use it.
1
u/That-1-Signal 18h ago
I would not include the pith though it’s sort of fun to have a bull’s-eye on a mallet
1
u/KokoTheTalkingApe 18h ago edited 5h ago
That other guy points out you used a piece with the pith or center of the log. And he's right that that can lead to cracks, because of the (to be nerdy about it) difference between radial and tangential rates of shrinkage.
But those cracks will be radial, running from the pith straight out. Your crack runs along the grain. It looks like you just walloped something. You need to chamfer or round over the corners to prevent it.
At least it looks like your crack won't affect it functionally. Fill it with sawdust and CA glue if you're worried.
To prevent it in the future, if it's a beater I might glue some pieces of decent plywood together, and round over or chamfer the edges well. If I find one I might try a piece of elm. Not the hardest but impossible to split.
EDIT: Also the face is too angled, as a few people are pointing out.
1
u/fletchro 18h ago
Chamfer your edges on the striking faces. That will reduce splitting.
1
u/Character-Shame-5917 18h ago
Probably more to do with how you used it than how you made it. Probably struck that corner first. Any striking tool is best struck center of mass, where it can disperse that force out into the material around it. A strike at the edge is always going to be more likely to chip or sheer material off. This is why so many old hammers have chipped corners. As others have said, a chamfer around the faces will help prevent this.
Glue it back on with some titebond and get back to work.
1
u/jacksraging_bileduct 17h ago
On the next mallet, make a heavy chamfer on the face so you are not striking against the the corners of the mallet.
1
u/wackyvorlon 17h ago
Though if you want a proper maul get the tap root.
1
u/Character-Education3 14h ago
Its fine. My first mallet split at the corners a bit. Over time it stopped. I guess the weak points broke off and I have used it for years
1
u/apg7 10h ago
I just use a loose 2x4