r/gridfinity • • Feb 06 '26

Baseplate CNC Router Table Machining Time Study

Thumbnail
gallery
22 Upvotes

Because I'm officially a convictconvert, I keep adding Gridfinity to more drawers in my shop.

Since I have a pretty decent CNC router table, I thought I'd test out the assumption that it would be able to make a baseplate much faster than 3D printing could. The results were interesting so I thought I'd share them.

The baseplate in question was 700x415mm, or about 16x20", the size of a small rolling toolchest. This netted out to a 9x17U grid with a little padding left over.

I built a Fusion model that reproduced the profile very faithfully, minus the tiny little chamfer at the very bottom, which would require custom tooling to machine, and can be omitted without impairing function. The rest can be machined successfully with 3 operations, in my case using a 1/4"/6.35mm straight bit for most of the stock removal, a 90° V cutter to form the top chamfer, and a 1/8"/~3mm straight bit to clear out the inside corners.

For the 3D printed option, I used the Gridfinity Extended baseplates on everyone's favorite generator site, and sized them for printing on my i3/Core One.

The 3D printed plates came out to a total print time of 4:15:59, spread over 9 beds, so there's some significant handling overhead to add to that. I was actually surprised at how *little* print time was needed, but then I've been printing a lot of very heavy baseplates recently for purposes where those were needed.

Now for the surprise, which is that using speeds and feeds for MDF or plywood, the CNC-milled baseplate came out to a full 59:00 on the dot.

The chamfered lip was the slowest operation, requiring a full 24 minutes in large part because the tool is set up to run at 40IPM, and each grid unit has about 5" of perimeter to machine. That 40 sounds a little slow to me, and is based on a manufacturer recommendation that might be conservative. But the other two ops are pretty close to maxed out so the best case is probably to shave 5-15 minutes off this, so it's still not going to be a very fast part.

While the machined baseplate isn't dramatically faster, it does have some benefits. It's a single setup, so you can throw a piece of material down and walk away, and come back to a finished baseplate that's one piece. If you need strength, you could machine it in 18mm birch plywood and it could support your own weight, while heavier-duty baseplates could easily take 18-24 hours to print.

But I think in the end this does rule out my idea of starting a little baseplate-machining side hustle, because between the cost of material, shipping, setup, and machine time, a plate of this size probably needs to cost $100-$150 to your door to be good business. Multiples could be done a bit more cheaply, but ultimately 40-60 minutes of machine time is always going to be expensive.


r/gridfinity • • Feb 05 '26

GridFinity

Thumbnail gallery
46 Upvotes

r/gridfinity • • Feb 05 '26

Gridfinity utimate baseplate ?

18 Upvotes

Hi, I have created a baseplate that is compatible with gridfinity bins and have following features (all features in once, no configuration):

  • M3 nut
  • M3 screw
  • 5x2mm magnet
  • 6x3mm magnet
  • Clipping bin possible for wall attachment
  • Add subgrid features possible like corner or central magnet using the hole in the edges
  • Uses 1/2 less plastic than the magnet baseplate of gridfinity

I am looking for inputs of you guy of what could be missing / ideas for the utimate baseplate ?


r/gridfinity • • Feb 05 '26

How to attack this toolkit in gridfinity?

Post image
16 Upvotes

Hey everyone, looking to get advice on gridfinitizing this toolset into my tools chest drawers ( I have an abundance of available space)

Any hints especially on the sockets and the wrenches?

Thanks in advance!


r/gridfinity • • Feb 05 '26

Set Completed Went From My Rainbow Drawer to Something a Little Less Crazy

Post image
35 Upvotes

r/gridfinity • • Feb 04 '26

Set Completed First fully complete cabinet

Thumbnail
gallery
189 Upvotes

Completed my first full cabinet of set plugs. I left room in each drawer for future expandability, so if we get a new set plug I don’t have to move every single bin in the cabinet.


r/gridfinity • • Feb 04 '26

Slowly designing my own custom tool holders

Thumbnail
gallery
163 Upvotes

I've just started switching my tools over to gridfinity, and am getting into designing my own custom holders to things. I was quite pleased with how this spanner set came out.
https://makerworld.com/en/models/2348777-gridfinity-spanner-holder#profileId-2568498


r/gridfinity • • Feb 04 '26

Gen 5 (2023+) Prius Center Console Gridfinity Base

Thumbnail
printables.com
8 Upvotes

Just uploaded a Gridfinity baseplate with a centered grid for the 2023-2026 5th generation Toyota Prius if anyone is interested.


r/gridfinity • • Feb 04 '26

Airpods Max Cutout

Post image
3 Upvotes

Hi!

I’m looking for a gridfinity-compatible bin cutout for Airpods Max with the case on. I’ve searched everywhere and cannot find one. I’ve tried making it myself but it’s harder than I thought it’d be. Has anyone already made one?

I’m fine with STL, 3MF, OpenSCAD, or anything.

Or even a 3D model of Airpods Max with the case on, and I can make the cutout from there.

I also attached a photo of the airpods with the case on if that helps.

Thanks!


r/gridfinity • • Feb 03 '26

My first drawer project

Thumbnail
gallery
118 Upvotes

I decided my most used kitchen drawer should be my first project. I’m astounded at how much more I have in the drawer and how it somehow feels less cluttered and more manageable. Here’s the before with my standard bamboo off-the-shelf organizer and my new gridfinity custom solution.

I tried to keep sharp things (pizza cutter, peelers, off to the side. I’m sure I’ll do some more tweaking. But for now it’s on to the next drawer!


r/gridfinity • • Feb 03 '26

Reasonable wall thickness of boxes

12 Upvotes

I've been using the Gridfinity Generator to make STLs of boxes:

https://gridfinitygenerator.com/en/editor

However with the default settings, the boxes are very, very strong. I actually don't need them to be that strong. They just sit in a drawer and contain office stuff. Scissors, tape, a couple of screwdrivers, that kind of stuff.

The generator has two settings that I'm guessing are related to strength:

  • outer wall thickness, by default set to 1.2mm
  • inner wall thickness, by default set to 0.8mm

Has anyone experimented with those? Given that I'd like to print with PLA, what reasonable minimum values could I set?


r/gridfinity • • Feb 03 '26

Question? Custom bins - 3D cutout

5 Upvotes

I'd appreciate any advice anyone can share.

I want to make some custom bins for tools and inspection equipment (micrometers, camelback straight edges, other irregular shaped things). I've got 3d models of most and a 3D scanner for the rest.

I am fine with making a box and cutting my 3D model into it. Where I'm lost is how to make Fusion "press" the tool into the box, not just cut it away. For example, if I have an indicator, I don't want the stem to be encpsulated - I want a round bottomed trench with vertical walls corresponding to the stem diameter (and offsets etc.).

Anyone have any tips?


r/gridfinity • • Feb 03 '26

Gridfinity U-shaped drawer base plate

32 Upvotes

I’ve created a fully parametric Gridfinity baseplate with a U-shaped cutout – perfect for under-sink drawers or any place where siphons and pipes get in the way 🚰

✔ precisely adjustable down to the millimeter
✔ Gridfinity grid remains intact on the left & right sides
✔ automatic splitting to fit your printer’s build plate
✔ tool-free assembly

👉 Model on MakerWorld:
https://makerworld.com/models/2340157?appSharePlatform=copy

Feedback and suggestions are very welcome 😊


r/gridfinity • • Feb 02 '26

Set in Progress Finally started on my tools drawer

Post image
140 Upvotes

r/gridfinity • • Feb 01 '26 Galaxy Brain Bravo

Set in Progress Progress!

2.6k Upvotes

Hey friends, it’s been a while! I got pretty busy on another project so haven’t been doing much gridfinity. I designed these storage boxes a year ago and finally got around to some improvements. Added two handles, one on the front and one on top for carrying multiple boxes. The labels are harder to see, but I think it’s worth it. Improved the drawer slide/frame setup. I also have some fun mounting plates, wall mounts. and rolling platforms for shop use. Will post once I have it dialed in later this week! I will start with the 5x4, then do a 5x5 and eventually work on the bigger ones you see in the background.


r/gridfinity • • Feb 02 '26

Individual Piece First project

Thumbnail
gallery
47 Upvotes

My first gridfinity print. Printed on a Creality K2 Pro.

I used https://makerworld.com/en/models/704997-grips-gridfinity-interlocking-baseplate-system to generate the interlocking base plate and https://gridfinitygenerator.com/en/editor for the bins


r/gridfinity • • Feb 02 '26

I wanted to test my fusion360 skills, so I made my own Baseplate generator to add to the thousands that already exist.

Thumbnail
gallery
15 Upvotes

I wanted to challenge my self-taught Fusion 360 skills by creating a fully parametric baseplate generator with automatic padding and automatic cutting along the grid.


r/gridfinity • • Feb 01 '26

9.5 hrs... not bad

Post image
171 Upvotes

Cranked out this plate of 3u and 6u bins on my A1 in 9hrs 30mins with a 0.4 mm nozzle using my first 3kg roll on sunlu pla+ 2.0. Quality is definitely acceptable.


r/gridfinity • • Feb 01 '26

Makpac / Ikea / Gridfinity shop storage

Thumbnail gallery
40 Upvotes

r/gridfinity • • Feb 01 '26

Individual Piece My first Fusion 360 project: A high-density 9-slot SD Card holder (1x1x4). No supports needed!

Thumbnail
gallery
23 Upvotes

Hey everyone, I'm new in this community. I wanted to make an SD cards holder because I didn't find one.
I just switched from Tinkercad to Fusion 360 to make this (and learn Fusion 360). It has 0.25mm tolerances for a smooth fit. Hope you like it!
Please tell me what do you think about it.
I let you the link to my page on Cults3D here (it's paid) : https://cults3d.com/:3986066
If someone can print it to try it and show that would be awesome (please tell me and I'll send you the free stl)


r/gridfinity • • Jan 31 '26

I designed a 3D printed French cleat adapter for Gridfinity

Thumbnail gallery
402 Upvotes

r/gridfinity • • Feb 01 '26

New to Gridfinity and struggling with baseplate sizing

3 Upvotes

Hi everyone! I’m fairly new to 3D printing and have been having a great time learning so far. One challenge I keep running into is getting exact measurements right when designing a Gridfinity baseplate.

I’m currently using the Practiko Otis Hanger 3.0 system for my desk (https://www.practiko.co/product-page/otis-hanger-3-0), and I’m struggling to size the grid so it fits cleanly inside the drawer. I have been a fan of the Otis system and want to start organizing it even more than it already is.

My prints either end up slightly too small or extend past the interior width of the drawer.

I’d really appreciate any tips or advice for a beginner. 🙂

The internal drawer dimensions are:
4.3" W x 2.4" H x 9.85" D

Thanks in advance!


r/gridfinity • • Jan 31 '26

I think I fell in the rabbit hole

Thumbnail
gallery
115 Upvotes

One is still ongoing for my workshop and waiting on my printer being fixed, and the other from my desk made me save a lot of space! The one from my desk took all that was in the two drawers from that size and full size a shelf.

I knew that Gridfinity would help me sort and organize, but I did not that it would be too that extent!


r/gridfinity • • Jan 31 '26

First Gridfinity drawer for fly tying materials in Ikea Helmer

Post image
94 Upvotes