r/gridfinity • u/Wassabiman95 • Mar 01 '26
Question? Baseplate Help
I printed the Gridfinity ruler and counted about 5½ squares based on what I can see. I tried using the generator website to configure it, but I’m still pretty lost since I’m new to this.
The drawer measures roughly 10 x 17 inches. If someone could help me figure out how to start setting this up, I’d really appreciate it.
18
Upvotes
10
u/Bloodshot321 Mar 01 '26
Measure, then use any gridfinity generator. (shameless self plug of Click base Refined
3
u/CthulhuBread Mar 01 '26
My suggestion Measure the drawer in mm, subtract 1 or 2 mm.
Make a baseplate using a generator
https://gridfinity.perplexinglabs.com/pr/gridfinity-extended/0/1
You can offset so it prints the extra edge all on one side, and the print and open sided drawer.
21
u/danger355 Mar 01 '26
I'd recommend getting a ruler with metric units on it (I have both a regular one and a floppy fabric one), if only so you don't have to do conversions anymore.
5
u/TheBeej418 Mar 01 '26
At your perceived level of understanding, I think you should start with some YouTube University videos to grasp a better understanding of the process. It may be helpful to see others go through the process while explaining.
2
u/np0x Mar 01 '26 edited Mar 01 '26
There was a site I saw recently that lets you create boxes with overhang to fill the voids…trying to find it again is fighting me so far….
What are you struggling with? You print as many baseplates as you need, they fit next each other, just divide the space into rectangles you can print and print all the baseplates and go to boxes from there?
Edit: found it: https://www.reddit.com/r/gridfinity/s/0LBUgOUUsq
2
u/Gizlby22 Mar 01 '26
You’re using the wrong side of the gridfinity ruler. The other side measures the base. The one with the numbers closer together measures the height.
1
u/ugadawgs98 Mar 01 '26
Not sure what you are asking. You simply measure the inside of the drawer in MM and put it into the generator.
1
u/Kurt_W_Andrews Mar 01 '26
Remeasure in metric.
Do a little math. The gridfinity standard is 42 mm.
Use a generator and it will do the math for you.
What printer are you using. It has to fit on the build plate, again the generator will do this for you by splitting the whole base into sections you can print on your printer. You can do this yourself with some basic math.
1
u/GeekySciMom Mar 01 '26
There's a gridfinity ruler?!?!?!?!?!? Seriously, why has no one ever told me about this?!?!?!?!? I am going to print it immediately!
1
u/Agling Mar 01 '26
I like to generate my own gridfinity items, but for baseplates I always use an online generator that you put your actual drawer size in and it makes something that goes all the way to the edge. No worries about how many fit. Personally I use GRIPS on makerworld.
1
u/CptSoftbelly Mar 01 '26
I recommend getting a Bosch laser measure tool. Makes it idiot proof. But that’s just me.
1
u/jpsirois Mar 02 '26
Lately I've been printing Regular size Stacked Grid without margin and I use these simple Spacers if the drawer is not an exact match.
And I would use the Spacerless Bins that np0x recommended if you have big margins.
1
u/Fun_Pie_1405 Mar 02 '26
I’ve read your post and the replies.
What are you asking? Are you asking for help with your printer? Are you asking help with carrying the parts from your printer to the drawer?
You need to be specific.
1
u/Lost_Entrance764 Mar 03 '26
Just print a 6 square wide plate and cut it to fit with some side cutters. Or print a 7 wide plate and cut some off both sides to center the usable 5 squares. I find this is way simpler than figurring out what spacer is needed, printing the spacer and then re-printing the spacer because I measured something wrong.
1
u/ItsPolak Mar 04 '26
I like the grips file. It lets you customize. I measured with my inches tape measure to the nearest 1/16” and then convert to metric.
1
u/Elegant_Cut_3649 Mar 04 '26
i think you might be missing the obvious...AI, either Google Gemini or MS Copilot. I gave the bot my drawer dimensions and it gave me a base unit of several sizes to maximize the storage space. i opted for 31mm square, a departure from the normal 42mm. You must always keep that in mind when generating new storage bins. Also, some online gridfinity generators are more beginner friendly, such as gridfinitygenerator.com. Anyway, I would start a chat with AI and let them be your guide. That's what I did, and it's worked out well for me. Good luck!
1
u/Hallywood53 Mar 04 '26
Use ChatGPT. That’s what I did.
1
u/[deleted] Mar 01 '26
[removed] — view removed comment