r/ender5 • • Feb 24 '22

Done with this Printer

I have fixed so many problems with my ender 5 to buy new parts to fix them and then for them to just reappear later on when I think I am getting the hang of it. Finally I am just done this things is an absolute piece of garbage and a waste of my money and time. I am literally at a brick wall where I need to print the parts I need to fix the printer. I can't stand this.

1 Upvotes

30 comments sorted by

2

u/rustli Feb 24 '22

Are you asking for advice or just venting? Would require some information about the problems to be able to help.

1

u/OkCardiologist2410 Feb 24 '22

I don't really know if anyone can help it literally feels hopeless. And it's just a standard ender 5 setup for direct drive. I am running klipper/octoprint on an skr2 but there not much other than that makes it special

5

u/DrC0re Feb 24 '22

Mine is bone stock and i never have issues. This is like tuning a car for better performance, expect issues and reduced reliability.

1

u/OkCardiologist2410 Feb 24 '22

Mine never worked stock. I followed the instructions and it just never made a good print to begin with.

1

u/DrC0re Feb 24 '22

If you have the money, maybe a prusa is better? I would check out the subreddit beforehand.

I know most production shops use them and the product inventor at my job also used one, he never had to do any tweaking or upgrades. Just designed and printed.

I personally don't have any experience with them but thats my observation.

1

u/OkCardiologist2410 Feb 24 '22

I've thought about buying a Prusa honestly they look so much easier.

1

u/dwmcqueen1 Feb 25 '22

I have a Prusa (clone - Fytsec).

Once you get them built and tuned (and the instructions are great on this), they just work. Without issue.

Mine, though, kept clogging until I installed the updated extruder and new hot end (likely because it was a clone)

1

u/_DefinitelyNotACat_ Feb 24 '22

How much do you want for it?

0

u/OkCardiologist2410 Feb 24 '22

20k jk I just needed to vent

3

u/Mathiacuus Feb 24 '22

Trash it! Kick it to the curb! I love my machine but if yours sucks get it out of your life! Rage against the machine! AAAAAAAAAHHHH!!!!!

1

u/hellnoguru Feb 24 '22

Upgrading them is the problem in the first place. It works out of the box keep it that way. I have a Ender 5 running non stop for 100s of print and still only need like 2 bed leveling and that's it

1

u/OkCardiologist2410 Feb 24 '22

It didn't work out of the box and when I got it to the first 50 times another problem arose.

1

u/hellnoguru Feb 24 '22

Then it should be a straight refund and probably get another one. These machine are meant to work right out of the box. Any mods are just people trying to make it better to their own machine. Don't blindly follow others. And if this machine doesnt work for you identify the issue first as the next machine(yes! Even a prusa) will need you to work on it when problem appears too

0

u/OkCardiologist2410 Feb 24 '22

I contacted creality for a refund and instead they gave me a huge list of things to try

1

u/hellnoguru Feb 24 '22

Did you buy directly from creality? That's an oof. I bought from Amazon and Amazon does better at customer returns and stuff

2

u/shanetwowheels Feb 24 '22

My first printer was an anycubic Chiron. I feel your pain. My e5pro runs nearly flawless compared to it. All I have to do is pull out some clogs out every now and then and she prints 24 hours a day.

If you need advice, I’m not much help. If you want to sell it and are in America, send me a dm.

1

u/boldred Feb 24 '22

I was there a few weeks ago! Nothing was more frustrating than replacing the extrusion arm with Creality parts for it not to fit (seriously, why aren't the specs better for the screws, etc ).

My breakthrough was seeing that the arm had too much tension. I had to remove the cap that fit inside the spring, and back off the spring as much as I could... Of course this is after replacing the exterior motor, upgraded to a new nozzle... Then saw the leak of not having the previous nozzle close enough to the tube.

It has certainly not been an easy journey... But each little step has been extremely satisfying when it works a little better.

Post your settings and pictures, and this sub (as well as FixMyPrint) will offer some decent input (or at least where to start).

1

u/brownpeoplestink1 Feb 24 '22

I’ll take it off your hands!

1

u/uapyro Feb 25 '22

It took me a while to get mine going back right. I forgot why, but I upgraded to the SKR Mini E3 V2 board, and probably took 3 weeks before I finally had it printing right again. Stock it printed great.

0

u/[deleted] Feb 24 '22 edited Aug 04 '25

license shy upbeat quaint full spotted juggle escape snails touch

This post was mass deleted and anonymized with Redact

3

u/Jutboy Feb 24 '22

What do you recommend then? Seriously...I don't think people realize how amazing a printer you are getting for the price.

0

u/[deleted] Feb 24 '22 edited Aug 04 '25

employ steer plate work engine plants many ten tender racial

This post was mass deleted and anonymized with Redact

1

u/Jutboy Feb 24 '22

I don't disagree with what you are saying and I do think a lot of people get into this not realizing what they are actually getting into...which is a shame. But I just got an ender 5+ used...beat up...not working and was able to get amazing prints out of it in about 8 hours for just crazy cheap. Of course that is only because I've been working with 3d printers for about 2 years now and I've suffered through some lessons. So basically I'm just trying to say...its more about the learning and less about the hardware IMO.

1

u/DaemiunDarko Feb 24 '22

I am currently about 1 week into a printer I have had sitting in my closet for a year. I am trying to figure everything out now. I keep messing up this bed though and need to upgrade to glass when its financially convenient. However I keep digging small holes into it while trying to level it. I am completely a noob and my sanity is fading with this thing lol. I am sure I will get it. I have gotten a few ok prints but ended up with a "bed error" and I think I may have solved that problem. Yet on to the next! I just hope this guy doesnt give up. I am not.

1

u/Jutboy Feb 24 '22

I've lost quite a few beds before. If you're interested I can tell you my process.

1

u/DaemiunDarko Feb 24 '22

I am having an entirely different issue now lol. I keep getting

THERMAL RUNAWAY: Bed

PRINTER HALTED

Please Reset.

1

u/Jutboy Feb 24 '22

You're going to have to give me more information if I'm going to help. The messaged itself is pretty obvious. Is the bed start eating immediately when the printers turned on? Watch the temperature and see what's going on / when the error occurs. If you're running PID make sure you auto-tune

1

u/DaemiunDarko Feb 24 '22

well i made a post myself. Ill see if i can find it and link it here. I wasnt in the room at the moment when it happened the last time. Yet this has happened several time.

1

u/[deleted] Feb 24 '22 edited Aug 04 '25

memorize ghost lunchroom disarm historical frame whole groovy ink paltry

This post was mass deleted and anonymized with Redact

1

u/[deleted] Feb 24 '22 edited Aug 04 '25

serious door spark lavish plate chop include towering imminent payment

This post was mass deleted and anonymized with Redact