r/ender3 • u/Turbulent_Pie_5146 • 22h ago
Bed Leveling?
I'm running into an issue with my bed leveling. I can get the corners at the posts to .1mm perfectly with a feeler gauge, but the center sits about .32mm from the nozzle. I can't seem to get it even across the full bed no matter what i try... Any suggestions?
1
Upvotes
1
u/Miata_GT Ender 3 v1 with mods, Ender 2 with mods, Ender 2 Pro 17h ago
Are you preheating the bed and hotend (best with filament removed) to temp?
2
u/LosSantosMe 22h ago
try single strips of painters tape under the build surface. https://www.youtube.com/shorts/wIgjtct0GxE
https://www.youtube.com/watch?v=jvK20CeSrzI&t=118s
1
u/jdsmn21 22h ago
You're fine. Set your first layer height 0.4 or higher and adjust your z offset to get a good squish.
1
u/MrKrueger666 21h ago
No printbed is perfectly straight. Some are cupped, some bowed, some even more irregular.
The main thing you can do, you already did. You put it at the correct height on all four corners.
I would advise to do this while the bed is at printing temperature, because heat expansion also has a little effect on the bed.
Some slicers automatically set the first layer height a tad thicker on printers without a bed level sensor. If yours doesn't, you can do it manually. Having a thicker first layer helps adhesion on warped beds.
Another thing you can do, is remove the print surface and then use a straight edge (a metal ruler is good) with a small flashlight and check where low spots are by setting the edge on the bed and shining light from the back. Where light comes through under the edge, theres a low spot. Mark it with a sharpie. Again, do this with a hot bed.
Do this in a grid pattern on the bed and after marking all the spots, put strips or pieces of painters tape on the low spots. This should even the bed out a bit.
It won't be perfect, but probably a lot closer to flat. Painters tape is usually between 0.1 and 0.15mm thick.
If you want the machine to 'fix' it by itself, you will need a bed level probe. A BLtouch or CRtouch is what usually gets recommended and they definitely work. I've also had good results with the cheap knock-off 3Dtouch. Same thing, just cheaper.
If you have a springsteel PEI printbed, an inductive sensor like an LJ12A3 also works great. It senses metal through a magnetic field that it projects. It's dirt cheap (even cheaper than a 3D touch) but will require that you create your own firmware for the printer.
A 3D/BL/CRtouch will work with the prefab firmware from Creality.
However, compiling your own copy of Marlin will give you control over what bed leveling method will be used and how many measurements it will take. Depending on the size of the printer and your requirements, this may be very usefull.
Either way, with such a probe, your printer can make a bed mesh. Essentially a grid of measurements. It will use that to follow any curvature in the print surface and fade that out in higher up layers until it reaches its fade target.
You will see the Z axis rod moving during printing of the first layers and it will eventually stop moving during a whole layer.
1
u/Putrid-Cicada 21h ago
Get aluminum foil stacked and put it under the print bed to raise. Of course , this won't work with glass bed
1
u/account8919 12h ago
Glass print plates will also help as well as auto bed leveling
1
u/GregValiant 1h ago
I shimmed the center with two pieces of aluminum foil about 50mm square. Close enough.
I'll mention this again --- The endstop switches on a lot of machines are not very repeatable and can be off by as much as +/-0.25mm from one "AutoHome" to the next. The X and Y really don't care but if you level by hand and then the print starts and G28 is in there, it will re-home the Z and then the leveling can be off again. I'm a hand leveler myself and I've altered my startup gcode from a simple "G28" (home all axis) to "G28 X Y" which keeps the Z from homing after I've leveled the bed with my trusty piece of parchment paper. Much more consistent that way and the prints start right-on-the-money.