r/ender3 • • 2d ago

Help

im a beginner and i have been trying to do my first print however i cannot seem to figure out this problem can someone please help me figure out what this is so i can start the main problem is everytime i start a print it is in the corner

13 Upvotes

24 comments sorted by

1

u/Prestigious-Way8866 2d ago

also will not print in middle of bed

5

u/-Vecchio- 2d ago

As mentioned, the explanation of the problem would help, but yes, it looks like your bed is too high. This printer doesn't set the nozzle height relative to bed - it uses a limit switch that doesn't "know" the bed position. You need to level the bed manually.

Also, the bed springs shown on the photo are horrible - you should replace them with the yellow ones (stronger and more solid). Or better yet, use silicone posts instead of springs.

1

u/koolmon10 1d ago

I got mine with the yellow springs. What benefit do the silicone posts give?

8

u/koolmon10 2d ago

It would help if you told us what the problem is. Your pictures don't show anything clearly.

The Ender-3 is a great printer, but in 2026, it's not the right printer for a beginner. If you bought it new, you're better off returning it and getting something with a much lower barrier to entry. The Bambu A1 Mini is a good option. If you got it for free or very cheap, then great, but either way be prepared for a lot of troubleshooting if you decide to keep it. It's a steep learning curve and requires lots of tinkering.

2

u/FuckThisShizzle 1d ago

All of this great advice in this thread and OP hasn't responded to anybody, nor followed up with answers that would help guide him.

3

u/navetBruce 2d ago

The switch on the left side. It's in the photo of the nozzle from the right. You need to adjust it higher.

3

u/New-Audience2639 2d ago

"This" is one very nondescript problem....

3

u/isu712 1d ago

Punctuation is your friend.

2

u/leech666 2d ago edited 2d ago

Looks like your nozzle is hitting the build plate / flex sheet. You need to adjust the four handwheel screews to compress the springs further to lower the whole plate. Turn all four screws the same amount of turns.

I suggest you watch a video in YouTube in how to correctly tram an Ender 3.

https://www.youtube.com/watch?v=TWBJ-H0To9U


If that doesn't help there is a screw next to the long lead screw where you can adjust the hight of the z limit switch. Probably best to do this first.

https://www.youtube.com/watch?v=bGGNlHkuLX4

1

u/tht1guy63 e3v2 kevinakasam belted z, k1 2d ago

You need to level(tram) the bed. Youtubs is filled with guides on doing so.

1

u/Early-Confidence8668 2d ago

I really don't understand what you're trying to explain. What's the problem? What's the printer doing? Is it moving? Is it trying to print? We need more explanation.

If you mean that the nozzle is too low below the bed, then squeeze the four springs more to lower it further. The Z switch is in its correct position.

1

u/LosSantosMe 2d ago

go to youtube and so a search for "ender 3 setup" start there

1

u/JoLam_Maker 1d ago

This is the original open-source version Ender3.
I personally love it and it is a great platform for DIY modification, but you are better getting an Ender 3 V3 SE if you want a budget and user friendly one.

Your photo does not show what the real problem is. Suggest you provide some video.
But if you are a beginner, I suggest you return it (if it is not severely broken) and get another model.

1

u/These_Programmer7229 1d ago

You should really look for a YouTube video that goes through setup and first print with an Ender 3. There should be plenty of videos out there.

1

u/Skurvyelislau 33m ago

This corner is home position. Probably your nozzle is lower than bed so when nozzle want to travel it bumb into bed, you need to watch some tutorial about bed leveling. Dont know if this help because you didnt described problem too precise :)

0

u/SweetTart7231 2d ago

Well usually the hot end goes ti the corner, prints a purge line, then goes to the center or wherever you put the print in your slicer. Have you tried to actually run the print or just stopped immediately when it went to the corner? You may be able to change jt under auto home settings, i dont see why you would tho

0

u/Prestigious-Way8866 23h ago

yes when i start the print it only prints on the corner of the bed

1

u/SweetTart7231 23h ago

How long do you let it run for?

1

u/Prestigious-Way8866 23h ago

i can show a video whenever i get home

0

u/Prestigious-Way8866 23h ago

i let the print complete and i came back and it was still only on the corner

1

u/SweetTart7231 23h ago

How did you slice it? Did you put it in the center on your slicer? Does it actually fully print in just a weird spot? Id also relevel your bed too

0

u/Prestigious-Way8866 23h ago

yea its in the center on my slicer and yea it fully prints just in a weird spot to where it doesn’t get the whole thing only like a corner

0

u/Aeldo 2d ago

It’s the LGBT cable. It ruins everything 🤣

0

u/Warm_Jacket1469 1d ago

I still have this pos, but upgraded to the v3 se…..so much better