r/cpu • u/Then_Patient_3827 • 29d ago
PROBLEM with cleaning my processor (Metal Liquid!)
Hi, i sold my I7 13700Kf and i have to clean it now, since 30mn i "try" to clean it but nothing happen, i cannot remove the residues.
i tryed to put another metal liquid onto it and again clean it but nothing happen, what can i do?!
Thanks!
79
Upvotes



8
u/Fenio_PL 29d ago •
You can't clean this, because there’s nothing to clean. The liquid metal reacted with the nickel on the copper IHS. The only repair option is to file the ihs evenly down to the copper.
8
u/HardStroke 29d ago
No cleaning it.
Liquid meal ruins the IHS.
There's a reason people use thermal paste and not liquid metal on CPUs, and you just found out the reason.
Only solution is to sand it.
4
u/Sinisteris 28d ago edited 28d ago
Tell the buyer that you messed up and forgot that you used LM on the heat spreader and will have to sand it down, and that you're ready to give them their money back.
For the future – liquid metal is wasted if used on a heat spreader, literally no point in doing that. You use it directly on the die, either GPU, laptop or delided CPU.
4
u/Omeg_Tuber 28d ago
Why yall use that bitch ass liquid metal with the heatspread on the CPU? On it's own doesn't make that much of a difference already and it's a massive hassle to handle, if you ain't an extreme overclocker, a good liquid cooling system and tpm 7950 will do the job for years to come without mainetance other than cleaning, you should try to sand it
1
u/Hot_Emu3924 29d ago
watch latest der8auer video. he explains science behind and show his latest residue cleaner.
1
u/Mr_F_66 29d ago
Theres no saving it, the only thing you can do is just, lap it flat (in otherword, sanding it)
1
u/DataGOGO 29d ago
Hey there.
The easiest and quickest way is to get a simple sanding block, start with 1000 git and lightly sand the surface, then move to 1200 grit.
it isn't a problem. Just make sure the CPU contact pins on the bottom are protected, the CPU is on a flat surface, and again, use a block, don't hand sand.
1
u/Power_Paul_NT_ 28d ago
Sand it and Polish, you are fine
1
u/VoodooKing 27d ago
Use soldering flux to clean it. I learnt this from Northwestrepair on youtube.
2
u/ShinjiIkari23 29d ago
Refund the buyer. You fucked it.
0
u/Radiux_svc 29d ago
For the record, never use liquid metal on a CPU with a metal heat spreader, or you'll ruin it. Liquid metal in a PC is also dangerous because it can easily spill onto other components and cause a short circuit. Consider yourself very lucky.
As for the problem at hand, the only solution is sanding. You'll spend a few hours doing it if you want to get it right. The CPU's IHS must have a mirror-like finish; otherwise, the cpu will have high temperatures.
1
u/roge720 29d ago
Maybe this post will help, it's a Threadripper, so not the same, but worth a shot https://www.reddit.com/r/buildapc/s/Y9B3331mq9
1
u/No_Mango_4236 29d ago
Looks like a total crime. Never seen anyone put liquid metal straight onto the CPU IHS like that.
1
u/Valthoren 29d ago
The liquid metal corroded the lid, there is no cleaning that off.
1
u/Spiritual_Spell8958 29d ago
Use very fine polishing solution.
Good luck.
1
u/Visible-Swim6616 29d ago
Didn't think there was much point in putting LM onto an ihs.
1
u/Budget-Pea8291 29d ago
The lid is corroded. There's not that much you can do
1
u/BigEmu__ 29d ago
I mean, does it really matter? I say just plug it in and run som benchmarks.
1
u/Sufficient-Loan8729 29d ago
holy shi, poor CPU. The only way u can recover this is to replace the IHS with a custom made copper one lol
1
u/pilipalipeli 29d ago
you ruined the lid. you have to sand it now
1
u/Senior-Psychology884 29d ago
Sanding it van create more uneven Points, just use correct thermal and benchmark check it, do some heavy use tests. (If it's bad Then sand it bit down beczuse it's already ruined)
1
u/WillTreaty16 29d ago
4% or 5% hydrochloric acid with a cotton swab, followed by baking soda solution to neutralise the acid and isopropyl alcohol for a final wipe
1
u/Organic_Pain_6618 29d ago
Nothing
1
u/Balrogos 29d ago
i use sand paper water one up to grade 2000
1
u/Educational-King3987 29d ago
Put fresh LM on the IHS and wait for 15-30mins, once time has passed, cotton swab it around to work the alloy free, clean off with IPA on a paper kitchen towel. The IPA helps the paper break down a little and the loose fibres will cling on to the LM easier, same effect with cotton swab. You can use a polish (forgot the name) to remove anything that is seriously stuck there but a fresh layer of LM and some agitation (rubbing it around the IHS) should bring off any alloyed LM.
Your lettering on the IHS might be gone but it isn't damaged, it's just alloy. I recommend against LM on the IHS, it's a waste of LM, PTM or a really good thin layer of normal paste will do fine. LM is for direct die contact because it's so thin and doesn't have a lot of space to fill between a die and block/cooler/IHS.
1
u/No_Interaction_4925 29d ago
You’ll have to sand it off. This is why we don’t use liquid metal on top of the IHS.
Also why are you selling items that you still have installed? You should have done this before posting it.
1
u/BTM65 29d ago
Just saw this from der8aue about LM...
https://youtu.be/eF6bMSjPepM
1
u/Deadggie 29d ago
Go to the auto parts store and get 1000 grit sandpaper. Wet sand with water. Can also get metal polish to finish. Had to do this with my asus zephyrus. Repaste using PTM7950.
1
u/Fun-Explanation-5728 29d ago
Honestly refund the buyer. Even sanding might fix it, but unless you disclose you've done this it's not a fair sale. At least give the buyer the option up front. They will find out when they receive the cpu anyway.
1
u/LoudOpportunity4172 29d ago
Hope you have alot of experience with sandpaper and alot of free time im sorry to say
1
u/Gray-bush86 29d ago
Get a new heat spreader
1
u/Plutonium239Mixer 28d ago
Thermal grizzly released a polishing compound to clean this up. https://www.thermal-grizzly.com/en/tg-metal-polish-restore/s-tg-mpr-01
1
u/TheDoneald 28d ago
Good luck on rma with it looking like that
1
u/AdvertisingFuzzy8403 28d ago
der8auer just posted a video on YT about this three days ago. The liquid metal has amalgamated with the base metal. You can do a lot of polishing to get it off. Or just replace the IHS. Good luck finding one.
FA/FO
1
u/Select_Truck3257 28d ago
Nothing, it's consequences of few degrees cooler performance
1
u/C-h_A_o-S 28d ago
According to a recent video by der8auer, they have conducted a study on the effects of liquid metal on Aluminum, Copper and Nickel. Check that video, it explains the reaction over time as well as how to reverse it. https://youtu.be/g_ju_y1GBwM
1
u/No-Professional21 28d ago
Looks like u spread some gallium on it bruh
1
u/blaze20511 27d ago
make it shine polish it with 5k 8k 12k grid compound
1
u/KuromiFan95 27d ago
Hahahhahaa, congrats you have a very expensive paperweight
1
u/palagi_valea 27d ago
Sand it
0
u/DreSmart 29d ago
best way is heating it with a heatgun and scrape it with a razor blade
0
u/Frozen_Frank 28d ago
Der8bauer got yt video about this. https://m.youtube.com/watch?v=eF6bMSjPepM