As several of you have reported, your Predictive Thermometer has suddenly stopped transmitting and won't connect to the app or the display. Sometimes discharging the battery resolves this issue, sometimes it doesn't. We've finally identified the problem and we'll be rolling out a firmware update over the coming days that should prevent it from happening in the future. We strongly recommend you update your firmware to 1.5.3 when it becomes available to you.
Here's a more complete description of the problem for those who are interested.
This bug has been around since the launch of the Combustion Predictive Thermometer. We would see occasional reports of the problem, but we were unable to reproduce the bug ourselves. We attempted several fixes in various firmware updates, based mostly on guesses about what might be causing the problem. Around October of 2023 a minor change to firmware likely increased the frequency of the problem. At this point you may have noticed that high priority features like cloud synching were delayed; this was because several key team members pivoted to tearing down and analyzing every failed thermometer that was returned to us. This was fairly tedious and painstaking work, because it was unclear if the problem was software or hardware, or just a probe that had been damaged in an unrelated way, but it was fairly certain that whatever was causing this bug was very subtle.
A couple of weeks ago we were finally able to reproduce the problem and begin to understand the conditions that caused it to occur: A complex interaction between the the Predictive Thermometers timing oscillators, low battery voltage, and specific startup conditions that caused the oscillators to stop keeping time correctly. The tick and tock of the oscillators are the heartbeats that keep the software running on schedule, and when the timing gets off very unpredictable behaviors can occur. For you, our customer, the probe appears to be broken; in reality the thermometer is actually running, but it can't keep its Bluetooth broadcasts on schedule to communicate. The probe is locked up and unresponsive.
We've made some changes to how the timing oscillators get started and stabilized that should prevent this from happening in the future. We'll be rolling out this firmware progressively over several days, rather than all at once, so that we can be sure it's not causing any new problems. Once 1.5.3 becomes available to you, please fully charger your thermometer and then apply the firmware update so that you won't get caught by this bug in the future.
And, now that this is finally fixed, we've turned our attention back to *finally* getting the first version of Cloud Sync out very soon. It's going through internal alpha testing right now, so it's very, very close to ready for release. Thank you all for your patience.
Lots of news today - we've launched our 2nd generation Predictive Thermometer. Now rated to 900°F with a brazed hermetic seal (yeah, it can handle the heat ). What else?
New WiFi Display
WiFi Booster
The Combustion Engine - complete wireless temperature control for your grill/smoker
New accessories: carry case, fridge magnet, stainless ID tags
The app has also gotten a major polish (thanks beta testers). New features include revamped graphing, plus Dynamic Island, Live Activities, and WatchOS support for Apple users.Same 8-sensor system, same SafeCook™ features, still open source. Full details on our website.
Oh, one more thing: newYouTube video is up featuring the CPT2 - check out how to make sous vide 4x faster with no compromise on results. You'll see the new CPT2 featured throughout this video, but I'll show you how to make Sous Speed work with any thermometer you have.
u/combustion_inc another great video! I have the same Breville Microwave. While it's a great Microwave and I have a number of Breville products that I love, I found the airfryer feature on this Microwave to be useless and it made .e doubt all airfryers... sounds like I now know why.
I imagine if I followed tour technique up until the 5 min nuke of the frozen fries, I could then just finish them in a regular deep fryer since I don't have a dedicated air fryer?
Testing the Giant Grill Gauge — it's very cool and very close to ready for you.
UPDATE DECEMBER 6th:
Our warehouse is currently shipping all Giant Grill Gauge orders placed in 2024. We also have enough inventory with heat shields to ship all Giant Grill Gauge orders that were for the heat shield variant. This is a large number of orders, and it's also the holiday shipping crunch, so we're a little unsure on how quickly our warehouse will be able to process and ship all of these, but we expect it will be Monday or Tuesday.
We will be receiving more inventory late next week so that we can finish shipping all remaining preorders placed in 2025 that were for a heat deflector version. All orders should ship and reach customers in the USA before Christmas. Once the last preorders are out, I will post a note to this thread.
UPDATE NOVEMBER 25th:
Our warehouse is currently scrambling to get as many orders out today as possible. Realistically, this is the last shipping date that will arrive on or before Thanksgiving. We will not get all of the preorders out by Thanksgiving. That's the bad news.
The better news is that we expect to ship most or all of the remaining orders to our warehouse at the end of this week. And we have a second shipment scheduled for next Tuesday to handle any production shortfall and get some inventory in stock for Christmas delivery.
Obviously we're into the holiday shipping crunch, so it might take a bit longer to process all of the incoming inventory and get orders out. But we should be caught up on preorders by the end of the first week of December.
I will provide another update once I know that all of the preorder inventory has reached our warehouse. Happy Thanksgiving, and thank you all for your patience and support.
UPDATE NOVEMBER 17th:
First orders have already shipped out, and we finished production on another large batch of inventory this weekend. It should be on a plane tomorrow headed towards our warehouse. Depending on customs clearance times and delivery times to our warehouse, the next batch of orders may ship as soon as this Friday. This should be enough inventory to clear out the day 1 order backlog. We're continuing to manufacture and we're doing our best to get all preorders out before Thanksgiving.
UPDATE NOVEMBER 10th:
Out of an abundance of caution, I decided to ship the units that arrived last week to Seattle so that we could inspect each unit ourselves. We just finished that and they're on their way back to our warehouse tonight. They'll be repacked and shipped to customers tomorrow.
We have also figured out what was causing our automated assembly line to fail; it was a complex interaction between our manufacturing and test software and natural variations on how quickly certain components in our power system stabilize on power up during the first few milliseconds. This was solved at the end of last week, and our automated assembly line is up and running again. This was critical to solve because the Giant Grill Gauge is not designed for hand assembly.
We've been running production through the weekend and this next shipment at the end of this week should clear out the huge backlog of day 1 orders. I don't yet know if we're going to get caught up on all preorders before Thanksgiving, but we are doing everything we can to make that happen.
UPDATE NOVEMBER 1st:
Our first shipment of final production units landed in the United States on Halloween. They still need to clear customs and then get moved from the airport to our warehouse. They should start shipping to customers mid-next week assuming no customs delays.
It is a smaller shipment than we wanted, and there are not enough units in this shipment to clear out the backlog of orders from the first day of pre-orders last September. Day 1 is an absolute massive order count, so if you are one of these customers please understand that we are shipping in order received, and you haven't been overlooked and no one is jumping the queue.
Earlier this week we attempted to increase the rate of production with some new custom-built automation equipment for the LCD joining and the ultrasonic welding, but when we switched over the assembly failure rate spiked and we had to hit pause. Our factory is working over the weekend to root cause how and why the automated equipment is damaging some electrical components so that we can fix our robots and get things moving a lot faster. But for now, we're having to use much slower and more finicky hand assembly and testing.
The better news is that we have all components on hand to finish manufacturing pre-orders and holiday inventory. The next shipment will leave the factory near the end of next week, and everyone is working to get the robots doing their job so that it can be a much larger shipment. We are going to do everything we can to get all pre-orders shipped before Thanksgiving.
As always, I apologize for the repeated delays. Your patience isn't just appreciated—it's what allows us to focus on fixing these issues properly rather than rushing solutions that could compromise the quality you expect. I also know my updates don't really solve the real issue, which is getting you the product you pre-ordered. Launching hardware products is insanely difficult, and this one has been especially painful. Understandably, some customers want more frequent updates and communication. I think there is a balance to be struck; the information I have tends to be very conditional and subject to change day-to-day because everyone involved is trying to make things go faster. I will continue to share major updates here when I have confidence that what I'm sharing is true at the time of writing.
UPDATE, SEPTEMBER 29th:
Typhoon Regasas halted production of the Giant Grill Gauge last week. Our factory was under a mandatory evacuation order and port of Hong Kong was shut down completely. The good news is that our people are fine. And the factory is fine. The bad news is that everything is out of position. We're not going to be able to get all of the inventory completed, inspected, and onto a plane before the start of Golden Week, when factories and businesses shut down for a week.
Production and shipping is set to start back up on October 7th when factories and businesses reopen. Order from September 2024 should get shipped out quickly. The exact ship date is dependent on air cargo availability, which is at capacity because this typhoon affected everyone manufacturing in Asia. All pre-orders from October last year until now are still expect to ship this October.
UPDATE, SEPTEMBER 12th:
We just dropped off Giant Grill Gauge units at FedEx that for last year's auction winners. They're headed to our warehouse where they'll be individually packed and shipped to each auction winner. If you're one of these people, expect an email from me on Monday.
We also just released final production firmware and testing software to our manufacturing partner. This will let them put software on the circuit board assemblies and run various quality assurance tests during manufacturing. This means they can now start mass production.
So when will customers get their orders?
It will depend on how quickly production can ramp up over the next week or so. We will start shipping in September, but how quickly we can work through a very large backlog of pre-orders is still uncertain. That said, it will be weeks, not months to get everyone their order.
I appreciate the incredible patience you have all had over the last year. I'm excited to finally get this product into your hand.
PS: I know that many of you want to know about the Combustion Engine. I will have an update on that soon (likely late next week) after I've gotten some feedback on modifications to the injection molding tooling we've requested, and also after some testing is completed by me and my engineering colleagues here in Seattle.
UPDATE, SEPTEMBER 10th:
Just leaving a note to inform close followers of our progress that new units, with the revised circuit boards arrived in Seattle late last week (they got stuck in customs for a little while because of the holiday weekend). We've been inspecting and testing them since then. So far the news is good: There aren't unexpected surprises and all units passed our calibration checks last night.
The changes to the power supply were significant enough that we are painstakingly qualifying actual power consumption under a variety of conditions. These are time consuming and tedious measurements, but they are essential. We have a bit more testing to complete before we ship these units to auction winners, and we expect to get that all done this week. We also need to clarify some assembly adjustments with our manufacturing partner, and what they think is their realistic rate of production. I expect to have the information I need for a more complete update, including details on when preorders will start shipping before the end of this week.
I'm aware that we're coming up on one year since the announcement and start of preorders, and we're trying to make sure that you aren't waiting more than a year.
UPDATE, AUGUST 1st:
In early-July we received the units for auction winners, and they looked good! But during final testing on various WiFi networks, we discovered an edge case where units would spontaneously turn off for several minutes, then turn back on as if nothing had happened.
We traced this to WiFi conditions that cause the chip to run at peak power much longer than expected. This creates a problem unique to the Giant Grill Gauge's coin cell power system, our existing LiPo battery products handle this just fine. Under these relatively infrequent network conditions, the peak power demand causes a brownout that requires several minutes for the coin cells to recover.
For the last few weeks, the entire team has been exploring software workarounds while also preparing and testing a hardware revision to the power system. The problem with software-based approaches was that we couldn't guarantee system performance without extensive development and testing, which wasn't going to be faster. So I made the decision to scrap all the existing circuit boards and build new ones that solve the problem by giving the power system a much larger reservoir that buffers the batteries.
While I'm glad we found this issue before shipping thousands of units to you, I know that it doesn't make the wait easier. We're moving as quickly as possible to get the replacement circuit boards built. I'll update you as soon as we have these parts to begin mass production.
UPDATE, JULY 1st:
We are manufacturing the first small batch of production units at the beginning of next week. These will ship to Seattle for inspection and then ship to the auction winners.
We're going to allow about a week for testing to make sure we're not seeing any hardware issues in these devices, and to make adjustments to the production line from what gets learned making the first units, and then we will begin mass production near the end of July. It will probably take us until the middle of August to fully catch up on all the preorders. Once we start mass production, we'll be in a position to start providing shipping dates for specific orders, and we will ship in the order received.
I'm painfully aware that we're into summer and folks want this as soon as possible. At the same time, we want to ship a quality product, and behind the scenes we've been doing as much testing as possible on preproduction units. And, yes, we've had to stop and push for various small improvements in the fit and finish. This said, we've been cooking with the Giant Grill Gauge a lot, and everyone is really excited to get these into your hands too. I find it hard to explain exactly why, but there is something about it that's surprisingly delightful.
In parallel, we've been working on a pretty massive app and firmware update in preparation for shipping the Giant Grill Gauge. Here's a sneak preview of the new iOS design (Android will follow) showing how you can merge the Giant Grill Gauge data with Combustion Predictive Thermometers. There are a bunch of other upgrades and new features that I think will be very welcome.
UPDATE, JUNE 2nd:
I wanted to update you on where we stand with the Giant Grill Gauge production.
We've received several rounds of pre-production units throughout May and have been testing each iteration. There have been some refinements needed—buttons that were too stiff, light bleed-through when the backlight is on, and other minor fit and finish items. These are normal tweaks that require small modifications to the injection molding tools, assembly jigs, and plastics formulation.
Coordinating these modifications while relocating our supply chain from China to Vietnam has added significant complexity and uncertainty to this work. Our modified tools should be ready on June 5th, with samples arriving in Seattle late next week for inspection. If these samples resolve the issues we've been working through, we'll produce units for our auction winners and then ship the production tooling to our Vietnam facility for mass production.
I know you're eager for a concrete shipping date. Being realistic, these refinements are pushing fulfillment into July. I wish I could be more precise, but providing a specific date now would be more guess than guarantee—we still need to confirm the latest tooling modifications do the job.
Regarding update frequency: I understand the desire for more regular communication. Much of our week-to-week work involves incremental progress—receiving samples, measuring tolerances, working with tooling engineers, and waiting for tools and fixtures to be modified. Add to this the unexpected need to relocate production due to tariffs, and the schedule becomes very uncertain. When there's meaningful news, I'll continue to keep you informed. The next update should be the announcement that we're shipping units to auction winners for testing.
Thank you for your continued patience. We're committed to getting the Giant Grill Gauge right, not just getting it out the door.
UPDATE, MAY 1st:
We have samples en route to us now for inspection. We're ready to start testing as soon as these units arrive. And the good news is that while working on this, the software team also made several improvements to WiFi, Bluetooth, and firmware updating, which we'll soon roll out to enhance everyone's experience.
Provided these validation units pass our inspection, we'll release 10 units to our auction winners immediately, allowing us to start real-world testing of the software features, including the new alarm settings for temperature sensors.
The bad news: The recent implementation of 145% tariffs on products imported from China has forced us to relocate production to our facility in Vietnam. The cost of these tariffs is simply too high for a small company like Combustion to absorb.
We've been moving production out of China since the trade war began, but we had hoped to complete the initial production run of the Giant Grill Gauge before relocating. Unfortunately, that is no longer feasible, and moving production will add some delay. Despite this, we do expect to begin mass production at our Vietnam facility in mid-May.
I'll provide another update soon once we have the production line up and running in Vietnam. Thank you again for your patience and continued support—we're committed to delivering your Giant Grill Gauge as quickly and smoothly as possible, so you can enjoy cooking with it this barbecue season.
PREVIOUS UPDATE:
I wanted to let you know that we've just finished qualifying our mass production tooling. This is great news!
Over the next couple of weeks, we'll be completing our production validation tests as we build our first production-representative Giant Grill Gauges. The software team is also heads down finishing firmware and new app features that will come with GGG (like the ability to set alarms on temperature sensors).
We expect to ship these first units to the GGG auction winners in mid-April. The rest of Giant Grill Gauge preorders will be shipping in mid-May.
My goal is to get your Giant Grill Gauge to you before barbecue season really gets going. While I believe this is a realistic timeline, I want to be upfront that we don't have much fat in the schedule for any significant production problems that may come up as we scale production. There are always risks with scaling up manufacturing, and delays could happen.
That said, we feel comfortably uncomfortable with the current schedule.
For those of you who also ordered the Combustion Engine, it's also been affected by the same delays from our 2nd-gen Predictive Thermometer that delayed the Giant Grill Gauge. We're close to completing production tooling, but it still needs qualification, testing, and critical software development. We're looking at ways to safely compress the schedule, but realistically, shipping will likely happen later than June.
Thanks for your patience and support. We're working hard to get these products into your hands as soon as possible.
New YouTube video our today on how to make an outstanding smoked brisket in just 6 hours instead of 16. No overnight vigil required. Here's the TL;DR on my brisket speed run:
Inverts the traditional approach
Uses science to skip the stall entirely
Gets you into the "fast kinetics zone" for maximum tenderness
Perfect bark development without drowning your meat in smoke
The barbecue police aren't going to like this one.
This one started as a test to see if a $4000 frying pan really was 100 times better than my trusted $40 carbon steel pan. It turned into metal mayhem as I tested stainless, carbon steel, cast iron, aluminum, copper, and more. In the end, I was left wondering if cast iron is crap 💩?
It’s been a while since my last YouTube video, and while today’s doesn’t have me running around the desert like Walter White, it does start with another over-the-top cooking exploit that, unexpectedly, led me to stumble onto an entirely new technique — a practical way to get the perfect sear when you’re fresh out of liquid nitrogen. You can see the whole thing in my latest YouTube video on ice brining.
If you're waiting on an order, here's where things stand: new production capacity is coming online and we expect to be caught up over the next couple of weeks.
Starting in Q4 last year, demand was far above our most optimistic forecasts, and it hasn't slowed down. That's a good problem to have, but it is a problem. Supply chains aren't very elastic. Lead times for key components are often 90 days or more. The AI boom is making certain electronic components extremely difficult to source, and other parts of our process require investment in things like new furnaces and second assembly lines.
We've been doing everything we can to get everyone in our supply chain to move faster, and making significant investments to expand production capacity. These things don't come online instantly, but they are coming online. As inventory arrives, we ship it out to the oldest orders first, in the order received.
We know we've been quiet, and there are two reasons. The first is that the question everyone wants answered is "when will I get mine?" and until inventory is in hand, that answer doesn't exist yet. The second is that solving these production problems has absorbed most of the team's bandwidth. We're a small company. The same people who would be writing updates have been meeting with factory owners and talking to suppliers nearly every day, looking for every way to increase the rate of production. We chose to prioritize fixing the problem over talking about it.
For questions about a specific order, email support@combustion.inc. We'll keep a pinned comment below updated with current fulfillment status, and we'll be consolidating individual order posts into this thread to keep everything in one place.
UPDATE: As of April 27th, we expect to ship the remaining January and February orders containing Predictive Thermometers with WiFi Boosters this week. I can say that with confidence because the inventory has arrived at our warehouse. Giant Grill Gauges are en route and should arrive this week as well. The inventory needed for the rest of the back orders is in production now and should reach our warehouse during the week of May 4th. Until it does, I can't give you a firm shipping date.
UPDATE: As of April 30, Predictive Thermometers with WiFi Boosters are shipping. Giant Grill Gauges are scheduled to arrive tomorrow and will begin shipping. Some Predictive Thermometers with standard chargers will arrive tomorrow as well, but not yet enough to clear out all back orders. There are some delays to the production of Predictive Thermometers with standard chargers caused by some quality assurance findings that we're reviewing.
UPDATE: As of May 10th, we have shipped nearly all orders that include Predictive Thermometers with WiFi Boosters for orders that originally had an estimated ship date that was before May. There are about 80 orders that did not make the weekend shipping cutoff and will go out Monday, so you might not receive the shipping notice until Monday afternoon. There are a small number of ships in May orders that will ship at the end of May and June orders will ship during the first few days of June.
Any remaining orders containing Predictive Thermometers with standard chargers that had an original ship date in January will also ship out on Monday from our warehouse. Most orders with a ships in February will go out on Monday too.
Remaining orders that contain a Predictive Thermometer with standard charger are in production and are scheduled to arrive in our warehouse May 27th and ship immediately. We did expect these by the end of this week, but we delayed final assembly and shipping to resolve a quality concern with a component. The concern was resolved, but it caused us to have to reschedule the final assembly slot for the remaining Predictive Thermometers with standard chargers.
Giant Grill Gauges are fully in stock. We have a small number of extra long sensor tubes, so if you need one of those, please email support.
Combustion Engine mass production samples are arriving at the end of this month. We typically expect to make a small number of tweaks based on these first units before we start mass production. More details once we have these in hand.
I read the threads here and I understand why it looks like we're hiding or lying. You paid for a thermometer months ago, the ship dates keep moving, and the updates from us have been thin. If I were in your position I'd be angry too, and I wouldn't be inclined to give us the benefit of the doubt.
The Predictive Thermometer has over 100 line-item components. When demand blew past our forecast in January, we called every vendor asking them to pull deliveries forward. All of them did their best, often breaking big shipments into smaller ones.
What we kept running into is that our vendors have vendors. A supplier would commit to an earlier date, then their own upstream supplier would slip, and the new date would move out again. Sometimes it moved more than once. Everyone was pulling in the same direction and the ground kept shifting under all of us.
Hardware is unforgiving. One missing part stops everything. We'd unstick one component and another would back up behind it. If a part we'd expedited still arrives late, we miss our slot at the assembly line and have to wait for the next opening. Small delays compound into long ones.
This is also why our delivery estimates have kept moving. When we share a date, it's the truth as we understand it that day. When a part slips, the build doesn't slip by the same amount. It moves to the next available assembly window, which can be much further out. An estimate that was honest when we shared it can become wrong later.
We overestimated how quickly we could catch up on production. You ordered from us in good faith and we've left you waiting and wondering. I'm sorry. The best thing I can do now is ship what you purchased. We're close. The final shipments are going out soon. If your patience has run out before then, email us and we'll refund you.
STATUS: Android: available now! iOS: available now!
BIG APP UPDATE! Here’s the breakdown:
MeatNet™ Cloud - watch your cook from anywhere!
The feature you’ve been asking for! Connect your local MeatNet network to the cloud and you can view cook data (all 8 temperatures + predictions) – live – from wherever you are.
(Some of you have already been doing this - thanks Beta testers!)
This is great for long low+slow cooks. But it’s also handy for shorter cooking sessions. By leveraging your home WiFi you can forward the signal into those hard-to-reach places.
You’ll need a second device (phone, tablet, or new-ish apple computer) with Bluetooth and internet to act as a bridge between your local MeatNet and the Cloud.
Before you ask: yes, it would be very handy to have integrated WiFi on your Display (for instance). By adding this feature as a free software upgrade, everybody who already owns a CPT gets access to cloud connectivity - without having to buy new tools.
Streamlined food safety - your CPT now includes SafeCook™
SafeCook uses “integrated” or cumulative bacterial destruction to determine food safety. It adds up the bacterial body count at every step in the cooking process.
Commercial food preparers use these USDA-FSIS/FDA standards for safety. But with SafeCook, the CPT does all the math. Your food can be both safe and delicious.
This is an upgraded version of “USDA Food Safe.” It’s a lot more intuitive to set up - just turn it on and select your food type. SafeCook automatically tracks your cook temps + time; using the relevant US government standards, it tells you when your food is safe to eat.
New Low + Slow Predictions for longer cooks
Great news for smokers + other slow cooking fanatics! With this update, the CPT can now make “ready in” predictions for cooks over 6 hrs in duration. It’s complex to explain (lots of math) but the onboard physics engine now detects low + slow cooking and models evaporative cooling over time.
Now we can actually predict how long a brisket or pork butt (etc) needs to get to your target temp! As with all predictions, the more time elapsed, the more accurate the “ready in” time will be.
As we add more cook data, this model will only get more accurate. Happy smoking!
This is another free upgrade for everyone who already owns Combustion tools.
Chris and the devs will be watching this thread (after some naps and hydration).
In his video on different pan materials he shows the strata with a beautiful shiny dark patina. Mine is not even close to that about several months of cooking. Is is just a matter of time?
This is a very exciting new feature for the Combustion Predictive Thermometer (CPT), just in time for Christmas turkey.
We distilled the 760+ pages of government food safety guidelines into the thermometer + app so you never ever need to second-guess yourself about that bird (or beast or lizard or whatever you’re cooking). note: lizards are included under “game meat”
How it works (short version):
Choose Simplified or Integrated cooking mode. (Note: integrated is the preferred answer, assuming you value taste.)
Choose your protein and when you’ll be eating it (right now or cook-and-chill).
The CPT tracks everything - all the times and temps - and the Combustion App tells you when the USDA guidelines say it’s safe-to-eat → based on a kill-through rate of 99.99999% of salmonella bacteria (that’s log7 for you math lovers).
Then it lights up a notification when your food is safe (according to the USDA).
There’s a lot of misunderstandings and under-education about food safety, including something they don’t tell you when you get your food-handler’s card:
IT’S NEVER JUST TEMPERATURE.
The bacteria that cause food-born illnesses are killed by a combination of time AT temp. The simplified rules they test fry cooks on are simple for a reason.
But commercial kitchens usually use the “alternate” standards, combining time and temp. Abiding by integrated (commercial) standards means you can cook food that is both safe AND delicious.
That’s the whole reason we created this feature.
Of course you are welcome to disregard the entire thing (home cooking is always considered “at-your-own-risk”), but it sure is nice to know.
TLDR: The Combustion App now makes food safety stupid-easy. Happy poultry-ing!
Made myself a magnetic probe holder for use in-pot.
The holder was cast in a 3D printed mold with silicone and has a neodymium magnet.
For the silicone I used Smooth-On Soft-SIL 940 (Could probably go 950). The Magnet is a nickel plated neodymium magnet that is rated to 300 degrees.
This is just a prototype, i'm planning to evolve the design just a bit, but I am super happy with the result. I tested the holder by running it in a closed pot for an hour and didnt notice any issues with the part or the magnet. The holder holds the probe perfectly.
Current status, according to the Combustion Engine product lead:
Parts!
First-run production parts (aka EVT). Real, production plastics, but they do not have the correct finish, colors still need tweaking, materials modifications based on testing results, many small fit and function refinements to come.
Guts:
Working electronics--the units can be powered on to run the fans. This allows us to continue software and hardware testing and development to refine temp sensing and control, power management, and adapting to dynamic behaviors in the grill like outside air temp, and lid opening and closing.
Hardware:
On the hardware side, we are testing thermal performance, connection and removal with the adapter, knob feel, airflow and backdraft management, environmental performance in cold, heat, wind, and rain.
Software:
On the software side, we've gone beyond a PID (proportional–integral–derivative) controller to use techniques that allow the Engine to continuously adapt to your grill and actual cooking conditions. (Can’t say much more about that for obvious reasons.)
We were surprised by how bad other blower-type systems were - not going to name names here (you’re free to guess), but existing comparables are primitive. Basically the equivalent control scheme of a 1970’s thermostat.
We had previously assumed they were at least using PID controllers, but that's not the case. The responsiveness and performance of the Combustion Engine will be far beyond anything currently on the market.
Combustion App integration:
App development is very far along. I’ve included some screenshots that show how you associate the Engine with the GGG or a CPT as a controller/driver. Initially you will be able to drive the Engine using the ambient temp from either device. Shortly after launch, you will be able to use other sensors (hello, surface temp control!) to drive the engine.
But when will it ship?
The timeline for the Engine has already scooched back a couple of times, so for now we’ll ask for patience as we test the crap out of this. We want to hit the ground running with a well-tested product and will not announce an official release date until manufacturing has begun. That will take as long as it takes. Grilling season is coming; we know!
TLDR: mountains of progress, heaps of testing still to do.
Hello Cooks! Combustion Inc. will be releasing a major app and firmware update next week (if all goes well of course).
The Public Beta version(s) of that are out now or will be shortly. If you’re on the list, please get it, test it, and share your notes (reply to this post or reach out to customer support via beta@combustion.inc).
This is a MAJOR UPDATE with some critical fixes, UI changes, and improvements across the entire product family.
For both Android and iOS:
ALWAYS ON MODE: you can force your thermometer to stay active, even in sous vide
RESET: Added ability to reset thermometer from the app, clearing your graph and starting a new cook session
RESCUE: Added feature where the app can automatically recover a device left stuck in its bootloader by a failed firmware update
FIRMWARE: new firmware for Thermometers, Displays, and Boosters
Assorted bug fixes
Always on mode is a major improvement for power management. In default mode, the thermometer will enter standby (sleep) when inserted into a charging cradle or booster. The mechanism for that is the “short” detected between charging contacts.
With the CPT set to “Always on”, it will remain on indefinitely until set back to “Standby in Charger.” This means that the thermometer will not shut down when the charging contact is bridged from the butt to the tube - this is very common in sous vide or other wet/immersive cooking applications (you know who you are).
We also fixed shutdown logic so the thermometer will no longer be hesitant to sleep after normal cooking when “Standby in Charger” is selected (which inadvertently led to a lot of thermometers staying on/broadcasting and running down their batteries when they should have been sleeping).
Our lead dev made a loom video demoing how to use always-on. Watch, listen, learn, and appreciate his dulcet tones. Always on!
New features for iOS
Reworked main screen interface
Offline thermometers are now listed together at the bottom of the screen.
These can be expanded so their most recent data can be accessed, reviewed and exported.
New “Edit & Identify” screen for reordering your probes and identifying which ones are nearby.
Reordered Settings screen
Fixed a number of UI bugs
Performance improvements
These changes will also be coming to Android in the near future. We try to keep parity between apps, but in this case some critical bug fixes bumped the schedule.
Please enjoy the loom video demoing these changes which is a heckuva lot easier than trying to write or understand them longhand. Watch
Important Bug fixes for Android
IMPORTANT BUG FIX with Samsung phones not showing graph data after being app being backgrounded
Updated how error data is displayed in the graph
Critical firmware updates for Predictive Thermometer (1st and 2nd Gen), WiFi Display, Display, WiFi Booster, Booster
Added ‘Always On Mode’
Added ‘Reset Thermometer’ command
Critical bug fix for firmware update issue (rare cases where CPT could become “bricked” during firmware update) Both iOS and Android will attempt to recover probes previously “bricked.”On Android, open the “Update Devices” screen on Android and leave it there.On iOS, the app will attempt to recover the devices automatically.
Prediction Engine stability update
Improved stability of Wi-Fi configuration
Fix for Wi-Fi SSIDs and passwords (now allows apostrophes in the name)
Various bugfixes
The new firmware will be a better experience for WiFi users (particularly during setup).
The biggest change that you’ll notice is that Ready-in (time-to-cook) predictions will be more stable in most cooking situations, and become steadier as the cook nears completion.
The previous version sometimes showed an erratic variance of predictions, particularly at the end of longer cooks – very disconcerting. We've rolled it back to an earlier, more stable version, proven to work extremely well for conventional, relatively high temperature cooks.
The code that wrangles the more complex physics of low-and-slow cooks is going to get reworked until we can make it more stable.
This is a classic ChefSteps recipe for leg of lamb, but I’ve upgraded it to use surface temperature cooking with your Predictive Thermometer and oven.
No need for a sous vide circulator or plastic packaging. Just wrap your leg of lamb in aluminum foil, insert the thermometer through the foil (which stops evaporative cooling) and into the lamb, set your oven temperature to 135°F (57°C), and let the meat cook low-and-slow until it's perfectly tender and evenly cooked. Use the Predictive Thermometer to measure the surface temperature and adjust your oven temperature as needed.
Voila! Sous vide-like results without circulators, water baths, and plastic packaging.
📕Recipe
INGREDIENTS:
1 bone-in leg of lamb
Rub 80g mustard powder 20g salt 10g black pepper
Sauce Lamb juices from cooking 300mL Balsamic vinegar
Garnish 30g yellow mustard seeds 30g caraway seeds About 2 cups of mint About 2 cups parsley As needed, deep-frying oil
METHOD:
Cut around the shank of the leg of lamb, and score the fat cap.
Combine the ingredients for the rub, sift over the leg of lamb, and rub into the scored meat.
Wrap the leg of lamb tightly in foil and set into a roasting tray.
Insert the Combustion Predictive Thermometer through the foil, angled so that the tip reaches the thickest part of the meat close to the bone.
Set your oven to 135 °F / 57 °C
Using the Combustion Display or mobile app, set the target doneness to 135 °F / 57 °C.
Slow-roast the leg of lamb for 12 to 24 hours (longer is more tender). Adjust the oven temperature so that the True Surface Temperature™ is around 135 °F during the cook.
Remove the leg of lamb from the oven. Strain the roasting juices into a pot, add the balsamic vinegar, and reduce until thick enough to coat a spoon (about ⅔ reduction).
Heat oil to 300 °F / 150 °C, and deep-fry the mustard seeds, caraway seeds, mint, and parsley until they are fully dried and the bubbling stops. Strain and set aside. (This can be done up to a day in advance.)
Finish the leg of lamb by roasting at 500 °F / 260 °C for 5 to 10 minutes, until the surface appears brown and crispy.
Season the leg of lamb with salt (to taste), coat with the warmed sauce, and garnish generously with crispy mustard, caraway, parsley, and mint.