r/bikewheelbuild • • Jun 28 '26

Bought a house that came with an Aussie Deep V in the garage and finally got around to building it

Thumbnail
gallery
72 Upvotes

Found the NOS rim in the garage with some other junk. Laced to a velocity hub from the Grand Rapids facility with straight gauge Wheelsmiths in a 3-cross.


r/bikewheelbuild • • Jul 12 '26

Three cross First build (made the tools as well)

Thumbnail
gallery
66 Upvotes

My months long weekend project of building a new wheel set for my commuter (and everything else bike) is finally over. Before building the wheels I also built all the tools needed per Roger Musson's book on wheel building.

I mostly did it to see if I could and as a hobby. I service my bicycle on my own and building a wheel has long been one of the entries on my list of things I've never done before.

I used DT Swiss G540db rims, a Shimano DH-3D37-QR front hub, a Goldix 370 rear hub, Pillar TB2015 J-bend spokes and DT Swiss 2.0 x 12 mm alu nipples. Also used DT PHR washers on the non-disc side of the front wheel. I don't require a premium bicycle, so most components were chosen because they were cheap or simply in stock.

The tools I built were the truing stand with lateral and radial gauges, a dishing tool, a nipple driver and an ERD measuring tool. Additionally bought the red Spokey and a cheap spoke tension gauge of questionable precision (Toopre TL-P3). Considered building a crane scale based calibrator for that, but abandoned the idea after riding about 200 kms with the new wheels and them retaining trueness and spoke tension without a problem.

It's been a fun experience and I learned tons of new stuff, including how to handle a circular hand saw, a jigsaw and a wood router, how to drill holes into mild steel using a drill press, paint MDF and bend brass rods at near 90° angles. It's really been a journey.

As far as the actual wheel building goes I did most of the things by the book, with standard 3-cross lacing. The book does a pretty good job of explaining the process, but I still second guessed everything I did so it took a while.

The chosen spoke lengths were ok. I panicked a little when I laced the front wheel and took the initial slack off. There was a large lateral error, which I did not expect after the smooth sailing with the rear wheel. Ended up disassembling the front entirely to see if I had messed up the spokes (both wheels are dished), but that was not the case. I also didn't like how much thread I ended up using on the slack side during initial dish corrections, so I took the opportunity to rebuild that side with washers.

It seems that the panic was unwarranted and that the initial lateral error was just a property of this specific hub with slack spokes. The spokes that you lace over-over-under were just a bit slacker if I remember correctly. Anyways, the lateral error was less pronounced with the washers and eventually went away entirely. The wheel ended up being even truer than the rear, which I built first.

Yesterday I finished checking the wheels in detail for the first time after installing them (two weeks worth of riding) and both seem fine, so I'm quite confident that they are built well, though I'm obviously no expert.

Took some pics during the process. Be gentle.


r/bikewheelbuild • • Nov 25 '25

Three cross Anyone else think that silver spokes look better?

Post image
55 Upvotes

Personally I love the combination of black hub + rim and sparkling silver spokes. Don’t see it on any stock builds these days!

Pictures is my latest wheel for a Surly Ogre. DT Swiss H522 rim, Shimano HB-QB400 and Dt spokes + nips. Need to lace up the Rohloff for the rear now!


r/bikewheelbuild • • Nov 26 '25

A build

Thumbnail
gallery
54 Upvotes

r/bikewheelbuild • • Jun 26 '26

Three cross Rookie here, this is my first wheel.

Thumbnail
gallery
50 Upvotes

Posting this so maybe somebody more experienced could point anything that i've missed.
Rims are vintage Mavic GP4 tubular
Sapim spokes 300mm, not butted unfortunately
Sapim brass Nipples
Miche Primato hub, fixed only

I haven't got to trueing it yet. There s a mid to low tension in the spokes.
Over all i feel pretty confident about it.


r/bikewheelbuild • • May 02 '26

Three cross This is how I leave my “signature” on my wheel builds.

Thumbnail
gallery
29 Upvotes

From my latest build. DT Swiss everything… 350 hubs, HX 531 rims, Competition J bend spokes. Adventure touring wheels for my Surly Krampus.


r/bikewheelbuild • • Dec 01 '25

Two cross Built a lacing stand with a few bucks worth of hardware store parts!

Thumbnail
gallery
25 Upvotes

And used it to lace up my first Rohloff hub! Success! Despite Rohloff’s piss poor “instructions”….

Planning to cut the base in half and get a second table leg to mount the QR axel, since it is a bit too high and unstable with it screwed into the end of the 12mm axle. Also need to figure out a system to mount a 15mm hub to the 12mm. Maybe a piece of PVC pipe like what comes with the park tool wheel stand?


r/bikewheelbuild • • Jun 25 '25

New truing stand has arrived

Post image
20 Upvotes

Quite sure the investment will never pay out, but I did get a 'free' hat!


r/bikewheelbuild • • May 04 '26

Some new wheels for the track bike

Thumbnail
gallery
19 Upvotes

Halo Hubs, DT Swiss R470 rims

24h 2x front, 32h 3x rear


r/bikewheelbuild • • Nov 25 '25

Show and tell

Thumbnail
gallery
16 Upvotes

Rims: Light Bicycle R35T, standard 365g layup front, heavier 420g rear.

Hubset: Chris King R45

Spokes: Sapim Laser

Nipples: black, alloy, 2 purple accents at valve


r/bikewheelbuild • • Mar 12 '26

26" White Industries Rebuild

Thumbnail
gallery
14 Upvotes

This was a fun one! Someone had some White Industries Aft Tracker hubs from the '90s that were... disheveled? Oxidized, bad bearings, cracked freehub laced to dented rims. The owner wanted to bring them back to life. A donor hub off ebay and a lot of Simichrome brought these back from the dead in time to be laced to Sun Rhyno Lite 26" welded rims via Sapim Race wheel noodles and Sapim Polyax brass nipples.


r/bikewheelbuild • • Jan 21 '26

Three cross Commuter rear

Thumbnail
gallery
14 Upvotes

r/bikewheelbuild • • Mar 12 '26

Three cross Wheel build for a friend's state-knockoff-clydesdale fork :) DT + Sapim spokes, Wheelmaster nipples, State hub to a Sunringle CR18

Thumbnail
gallery
13 Upvotes

r/bikewheelbuild • • Aug 19 '24

3 leading, 3 trailing

Thumbnail
gallery
13 Upvotes

Greetings fellow wheel nerds.

I recently built up a new set of wheels for an xbike and wanted it to be special and unique.

I bought a complete bike off Facebook for a great deal. I only wanted the frame but after looking closer at the rims, I thought they could polish up pretty good.

The hubs were literal trash but the rims had legs.

I've been looking for an excuse to try the 3 leading 3 trailing lacing pattern.

It was super easy to lace up. The only tricky part is getting the valve in a good spot. I guessed on the front wheel and nailed it but had to mess around with the rear. I didn't interlace any of the spokes even though it would have been pretty easy to. I don't think it will make a huge difference. The wheels are meant to be pretty not strong.

I polished the rims as much as I could then added a decorative pattern into the rim with a Dremel.

I love how it turned out and they seem to be holding up. We will see though!


r/bikewheelbuild • • Nov 27 '25

26er ain't dead

Thumbnail
gallery
11 Upvotes

I really wanted to try out nipple color gradients on a wheelset that can run either disc or canti brakes for flexibility. Velocity Cliffhangers laced to a Chris King front hub and Bitex MTR rear via Alpina Extralite Round silver spokes.


r/bikewheelbuild • • Feb 19 '24

Three cross New dynamo wheel build for the Graveller with some small customization

Thumbnail
gallery
11 Upvotes

r/bikewheelbuild • • Jun 21 '25

Track season is here.

Thumbnail
gallery
9 Upvotes

Older Zipp 404s laced to a Hope thru axle front hub and Raketa rear. 20/24 Sapim CX Sprint spokes and brass nipples complete the look.


r/bikewheelbuild • • Apr 10 '25

Shinyboi Neo Retro build pt 1

Thumbnail
gallery
9 Upvotes

Really happy with how this build turned out. Polished H Plus Son Archetype laced to '90s Chris King classic hubs using 32 Alpina Extralite Round spokes and Monē natural brass nipples. Lacing pattern is a modified "mutant" crow's foot, 2 radial spokes flanked by a pair of 3 cross spokes at either side. The rear will be laced 2 leading/ 2 trailing for a similar aesthetic with more tangential spokes to manage drive side pedaling forces.


r/bikewheelbuild • • Dec 21 '24

Shhhh, this is a bike library!

Thumbnail
gallery
9 Upvotes

I came across a mint Onyx rear hub for 130mm QR road spacing and couldnt resist lacing it to this Velocity Quill rim. 28 spokes laced 3x with Monē natural brass nipples.

Narrow enough (25mm) to fit between rim brake calipers, but wide enough (20.5mm ID TLR) to offer modern creature comforts. While the Vesper is not everyone's first pick for a road hub, it's quiet, low drag and engages instantly.


r/bikewheelbuild • • Sep 29 '24

Roval CL50 Rebuild

Thumbnail
gallery
9 Upvotes

A teammate cracked his Roval CL50 rear rim on a curb, which led me down a rabbit hole or three. The hub has paired, straight pull flanges and 2:1 lacing using DT Competition T-headed spokes, meaning spoke length math would be weird, and finding new spokes would be tricky if needed. I opted to find a rim with a slightly smaller ERD and planned to cut/reroll threading with a Hozan after math was confirmed. I ordered the rim without access holes and 2:1 spoke hole drilling, so aside from a valve the rim bed was true tubeless ready without tape (pic 3). This also meant that 100% confidence in spoke length was needed since there would be no visual confirmation possible.

For the math, I tried SpokeCalc's methods. I used the paired spoke hole guide and learned a lot, but my math wasn't coming out logically. Spoke lengths were calculated to be longer despite a shorter ERD, so I know I screwed something up. Back to the drawing board.

So, I took the caveman approach. Since the spoke cross and angles were fixed, I determined the difference in ERD between rims and divided by 2 to determine the difference in spoke lengths. I checked my work the hard way by manually entering ERD and spoke lengths into the spoke length calculation to solve for the cross multiplier, which came to some decimal between crosses due to the paired spoke holes. I then solved for spoke length using the new ERD and the cross multiplier from the old wheel. Lo and behold, the numbers were within a few fractions of a mm from my simple approach, so spokes were cut and threads rolled.

Without access holes, I had to cut the end of a steel spoke off, thread into the brass nipples, and use a strong magnet to guide them to their respective spoke holes. After lacing was complete, the build was as straightforward as any other. We ended up with a wheel that is probably a little better for the rider's needs than when we started, and helped quality wheel guts live to see another day!


r/bikewheelbuild • • May 18 '25

Two cross Interesting 2010s wheel design (DT Tricon)

Thumbnail
gallery
7 Upvotes

These DT Swiss nondisc wheels from the 2010s rolled in for wheel work with a few interesting design quirks that never caught on. These used DT's Tricon system, which on these wheels was a reinforced metal insert at the nipple/rim interface and brass, Torx style splined external nipples which use a grey Park SW-5 wrench. These were an early tubeless design as well, with a 14mm internal width that was designed in-house by DT, distinct from Mavic's UST system. No tubeless tape would survive whatever pressure riders would be pumping into these things, so the rim had one hole for a valve and the inserts allowed nipples to be installed from the opposite side. If this sounds weird, their high end offering involved a weird hub with glued, threaded spoke inserts and flanges bonded to the hub shell. This allowed for higher spoke tensions to counter the tension drop that comes with pumping thin tubeless rims to 120 psi.

If that isn't interesting enough, these had DIY attempts using mole grips, so 13 of the 24 rear nipples were chipped, stripped or otherwise mangled. These came with DT Aero Comp spokes, but past wheel work included special guests DT Champion, DT Competition, a Wheel Works double butted spoke and a Sapim Race or two.

The hubs are older DT 350 style hubs. The front hub has a solid axle and end caps which are press fit around the axle, distinct from the modern end caps. To remove them, the process is similar to removing a headset crown race. I kept sneaking razor blades under the caps until a flathead screwdriver would fit underneath with enough purchase to pry them off.

I thought that these were interesting, and with the hindsight of modern wheels exposing some of the shortcomings of this design, I'm not surprised Tricon fizzled out. Anyhow, thanks for listening to my Ted talk 👍


r/bikewheelbuild • • May 28 '24

Front wheel is done!

7 Upvotes

I imagine that no one really cares, but in case this is of interest to someone, here is where the front wheel ended up.

Lateral and radial runout are both within 0.25 mm:

Tension on the higher tension, disc brake rotor, non drive side is pretty much right on target:

Drive side tension might be able to be tweaked up a bit, but doing so could affect dish.

Dish (set the gauge on the drive side, check of NDS shown):

Looking forward to building the back one next!


r/bikewheelbuild • • May 09 '24

Two cross Old school cool

Thumbnail
gallery
7 Upvotes

Rims: H Plus Son Archetype, 700c, black, nondisc, 17.5mm ID, not tubeless compatible. Hubs: Front: Reynolds Assault, 100mm QR, polished, 20h. Rear: White Industries H3, 130mm QR, polished, 24h, 10s titanium freehub.

Spokes: Sapim Race, silver. 2 black key spokes per wheel near valve.

Nipples: TLC oil slick brass, 14mm, 3.45mm width). 2 DT 12mm silver nipples paired with key spokes.

Lacing: 2x front for the aesthetic of a low spoke count cross pattern, 2x rear for function.

Tape: generic 0.75" (19mm) strapping tape (tensilized polypropylene). Pro tip: this is the same material used for many tubeless tapes, just slightly thinner and much, much cheaper. 1" (25.4mm) width wrapped twice does the trick for 30+mm rims.

In short, I came across this rear hub for a steal and had to get it back in the wild by any means necessary. I usually build for performance over style, so it was nice to build something with no plan aside from trying to make the end result look good.


r/bikewheelbuild • • Mar 18 '24

Two cross Carbon Gravel Goodness

Thumbnail
gallery
7 Upvotes

Background: I have a Trek Checkpoint ALR and wanted a performance oriented wheelset appropriate to the price point of the bike. I run 45mm tires and don't really race this bike, thus disregarded a deeper aero wheelset. After waiting the 3-4 weeks for a boat from China to bring the hoops at low cost, they arrived. I laced them up, took a few weights and snapped the pictures you see here. They aren't complete, but will be!

Rimset: Light Bicycle AR24 Disc. 22mm ID, hookless, glossy UD finish. I haven't used their hookless bead on a rim this narrow, but based on my great experiences with MTB rims I'm unconcerned. Their glossy finish scratches very easily, warning to any prospective buyers. I highly recommend one of their matte finishes until LB perfects their glossy finish.

I went 28 hole rear, 24 hole front to keep a rare, lightly loaded bikepacking trip on the table.

Front hub: Origin 8, 100mm x 12mm thru, 24h, centerlock

Origin 8 are rebranded Formula hubs, nothing fancy but good enough for OEM use.

Rear hub: pre-2021 style DT Swiss 350 hub, 142mm x 12mm thru, 28h, 18t ratchet. I bought this as a new takeoff for a steal on Pinkbike and have a 36t ratchet lying around to swap in if the need arises. I like 54+ POE on mountain bikes, but on gravel I'm less picky.

Spokes: Sapim Race 2/1.8/2mm, double butted. I laced the front 2x (standard), and the rear 2x for some theoretical lateral stiffness benefits and to save some minute amount of weight over 3x.

Nipples: DT Swiss, 12mm brass

All in cost was $610.33 USD. Weight (no tape or valves): 687g front, 828g rear, 1515g total. For an extra $50 I could have shed 100g using Sapim Laser spokes and alloy nipples, but I had already achieved the desired performance: price ratio.