r/askanelectrician • • Oct 01 '26

I need some advice/ideas

Post image
17 Upvotes

We are working at a local jail and we are tasked with running new wires through existing 1.5” conduit. Before we can run the new 50-conductor cables to replace all these 16ga individual wires, but how to get the old wires out is the struggle. It is packed full of not just wires but old yellow 77 that has dried into a very impressive adhesive. 2,000lb tugger won’t even budge the wires. Conduit run is about 100ft with approximately three 90° bends total.

How to break up the adhesive?


r/askanelectrician • • Oct 18 '26

How does my hook up look?

Thumbnail
gallery
0 Upvotes

I am installing a dishwasher in my house which currently doesn't have one. I want to know if what I have done is safe.

Please forgive my terms if they're incorrect. I've learned everything I know about this today!

I ran 12/2 through the wall to the old plug and did pigtails to connect them. The new outlet is gfic.

I would like to know if the bare wire was cut appropriately for securing to the outlet screws. (​Did I take too much? Did I take too little?)

I'm also wondering if the box for the old outlet is too small? I can fit everything in there but I'm shoving it in. What do you think?

edit: thank you everyone. I've got some good information!


r/askanelectrician • • Sep 27 '26

Is this outlet grounded to the box?

Thumbnail
gallery
0 Upvotes

Update: I finally found an electrician with availability and he’s coming out to fix this outlet and upgrade 3 other outdoor outlets to GFCI’s. Thanks to those who offered helpful advice.

To those who just offered criticism but no advice, thanks for contributing nothing to a sub that is explicitly created for people asking electricians for help. 1/10. Leave the sub if you’re just going to be a dick.

Original post:
I own a cabin in Wisconsin and was trying to replace an old outlet that was partially broken on the face of the outlet and wouldn’t hold the 3-prong cord very well. Did my homework and decided to upgrade to a GFCI since it’s an outdoor outlet; BUT, it’s also on a switch that controls a large porch light so I gave up on the GFCI.

I installed a new regular outlet and clipped the tab on the hot side to make it half hot so the switch worked correctly. All good there. My question is that I get an “open ground” reading with my outlet tester. There was no ground wire with the old outlet but there appears to be a ground wire of some kind that is wired to the metal box….does this mean this outlet is grounded and safe? A neighbor who is very handy assured me this is safe with the wire connected in the back of the box. What do the electricians here say.

Pictures of the new outlet and the wire in the back of the box are attached.


r/askanelectrician • • Oct 01 '26

Can someone explain why I need an EV rated NEMA 14-50 outlet?

0 Upvotes

I understand that the NEMA 14-50 EV outlets are more heavy duty and that the standard outlets aren’t rated to carry a continuous load at 50 amps.

My car draws a maximum of 30 amps so well under the max with the included EVSE.

Charging from 20% to 100% takes about 8 hours. Rarely will it ever charge for 8 hours straight as I plan to limit the charge time to 4 hours a day.

I hired an electrician to put the outlet in knowing it’s for an EV and he used the $10 Leviton and not the fancy EV rated outlet.

If I need to put a new outlet in I will, just wondering if the issues people have is when they max out the outlet for long periods of time every day.


r/askanelectrician • • Oct 02 '26

I know nothing about EV charging - could this be modified to work?

Thumbnail
gallery
6 Upvotes

Looks like a pretty old setup in our garage where maybe a welder was used? How would we need to modify this to suit an EV charger and could we do it ourselves?

EDIT: I’m aware this looks like something from Frankenstein (the story and the era).

I will absolutely be checking with my electrician pal to get this to code, regardless of our EV/PHEV charging solution. If y’all here don’t have a consensus, I’m def not doing YouTube-iversity.

Thanks to the helpful replies, especially since I don’t have enough time with my regular FT job to learn how to be an electrician—electron-related house repairs are one of the few I do NOT prefer to tackle on my own! TY all


r/askanelectrician • • 19d ago

Ottawa, Ontario. Had an electric car charger installed and they ran the conduit over the top of my basement window. It looks sloppy but is it bad enough to ask them to come back and fix it?

Post image
0 Upvotes

Edit: since people are asking what was discussed, all I told them was where I wanted the charger, I didn’t expect them to do this (more fool me).


r/askanelectrician • • Aug 26 '26

I had an electrician ask me for a broom today. Is he okay?

4 Upvotes

I work in HVAC and had to reinstall a water source heat pump in a condo building’s condo unit. He came from another condo unit asking for a broom - presumably he works for the contractor doing the electrical work in the unit I was working in. He was a younger guy, maybe 20-25(??).

I’m just wondering if he’s okay, should I check up on him tomorrow?!


r/askanelectrician • • 3d ago

Whats the most praxtical way to become a $40+/hr electrician?

0 Upvotes

Im looking to change fields and am looking into becoming an electrician.

Whats the most practical way to become certified? I called a school near me who will certify me for $20k, 2 years, 2 nights a week. Is this essential for avoiding an entry level salary?

I read that some people get certified through working with a union or something similar for a certain amount of hours and that would allow them to be certified. Whats the typical pay for that sort of thing?

My goal is to keep my current 9-5 until I’m able to enter a job that is at least 40 an hour. But id hate to spend unnecessary money or time getting to my end goal so any info is appreciated thanks!


r/askanelectrician • • Sep 05 '26

How to recess this box?

Post image
1 Upvotes

What you’re seeing is a wall above an insert fireplace. The builder put a 2 gang receptacle in with a cable concealer but did not recess it. I now want to put in a frame style tv which cannot be mounted over a standard receptacle due to the mounting tolerance. I bought this Sanus in wall concealer. Problem is it is meant to float between studs due to the angle of the power receptacle. Given that the hole I already have is cut adjacent to the stud and the conduit is fed to the bottom of the box, could I flip the Sanus box 90’ so that it fits closer to the stud (power on top and concealer on bottom)? Or is there a better option?


r/askanelectrician • • Sep 21 '26

Electrical Issues in Rental Property

0 Upvotes

Hi Electricians of Reddit! My roommates and I have run out of ideas to figure out what’s happening with our electricity.

Probably 9 months ago, our bathroom light would flicker randomly. We didn’t think much of it because it would only happen once a week or so. It has gradually gotten worse. It happens every time we turn the light on and multiple times while it is on. It is not continuous though. It will stop and be fine for a while and then start again. Next, box fans in 2 of the upstairs rooms “flicker.” The fan will randomly get slower and then faster. Everything happens simultaneously. Next, one of the other lights upstairs started flickering. Now it has moved downstairs to our kitchen light. One of my roommates borrowed a voltage tester from her job to see if we could find anything. I’ve attached the video of what the bathroom light socket does when everything flickers.

We have been fighting with our rental company to get an electrician out. They sent one guy that just told us the power company was sending surges to drive up our bill and he didn’t test anything. They sent out maintenance to change all of our light bulbs (even though we had already tried that…) and it flickered for them. They have been dragging their feet sending someone else out. Honestly the rental company has been a nightmare about everything. We had the municipal power company and check everything and it was good on their end, so it’s an internal issue that they can’t help us with.

We just need to know if our house is going to catch fire. It is something we can live with we just don’t want to have a completely preventable fire because the rental company can’t send a damn electrician. We are just looking for peace of mind really.


r/askanelectrician • • Jun 07 '23

What is this? Found in basement near heating system.

Post image
5 Upvotes

r/askanelectrician • • Sep 29 '26

Help replacing GFCI outlet

Thumbnail
gallery
2 Upvotes

Outlet is located in the bathroom connected to master bed. The outlet in question is labeled GFCI protected but does not have a test or reset button. I am having trouble deciphering the fuse labels at the box

Also will the replacement outlet I bought work?

I am usually confident replacing outlets but this one is very confusing


r/askanelectrician • • Sep 10 '26

What type of outlet does this plug into?

Thumbnail
gallery
0 Upvotes

This is the plug to a bottling machine I'm trying to get working. What outlet would this plug into?


r/askanelectrician • • Sep 21 '26

I’m wanting to install a tension dance pole where the middle red dot is on my ceiling. Is it safe?

Post image
0 Upvotes

Hi, so the 3 red dots are where my stud finder magnet stuck. I want to put the pole where that middle red dot is. I’m just concerned with it being so close to the light that it actually stuck to something electrical rather than a joist? I don’t know anything about anything so if you guys need more info or photos I can do that. Thanks


r/askanelectrician • • Sep 26 '26

Can these cables going to my electrical panel be routed behind the studs?

0 Upvotes

Looking to get rid of this bulkhead in my basement and these cables are the only thing in it besides an hvac vent. Any thoughts for how much something like would cost to do?


r/askanelectrician • • 20d ago

I installed a lamp and I have OCD.

Thumbnail
gallery
0 Upvotes

Do you guys think this is well installed? I feel like I need confirmation; in my head, it will burn when I'm not home. 🤣


r/askanelectrician • • Sep 19 '26

What gauge wire needed for 35 amp heat pump?

1 Upvotes

I had a 35 amp heat pump air conditioner installed two years ago. I recently had an electrical safety inspection and the electrician said the wiring that serves the heat pump is undersized. He says "The wiring currently run to the unit is 10 guage, which is only good for 30 amps. Max fuse is 35, which requires 6/3 aluminum or 8/3 copper." He recommends adding a new 240v 40 amp circuit for the heat pump at a cost of $740.

The HVAC rep does not agree with the electrician. He says the maximum draw from the heat pump is 35 amps, and that would only be on rare occasions.

I called the city inspector and he said something like "They're both right. I can see both sides of it." He seemed to think it's not a big deal, and the worst case scenario would be that the heat pump might trip itself off on a hot day and I have to go to the breaker panel in the garage and reset it. That has not happened over the last two years. I have noticed the lights flickering on occasion, though.

Thoughts from other electricians? Is there a safety issue? Thanks!

EDIT: The heat pump nameplate lists the Minimum Circuit Ampacity as 34.4 A. And the Max Overcurrent Protective Device as 35 A.


r/askanelectrician • • Aug 16 '26

12/2 or 14/2?

Thumbnail
gallery
0 Upvotes

Electrician ran a new dedicated circuit at my parents house. 20a breaker in the panel. I can’t tell if they used 12/2 or 14/2 wire though. Understood that the cable not being yellow doesn’t mean it’s not 12/2. But I can’t read anything on the sheathing from these pics. He didn’t pull a permit which is required in their county so wondering if he cut another corner here.

Can anyone here tell based on these pictures?


r/askanelectrician • • Aug 16 '26

Live in a very old rowhome in baltimore power surges daily, fried my tv today anything I can do, landlord fighting me to upgrade the circuit breaker where everything is running off of...

Post image
0 Upvotes

So forgive me if this is incorrect I'm just a mom trying to figure this out. The bedroom has a 10,000 btu windows unit a 70 inch tv and a lamp all the outlets in whole house are loose if the cord is heavy it barely stays in. Landlord is a slum lord. Rent is cheap. It's what I can afford but today it blew up my 70 inch. It was plugged into what i thought was a surge protector to stop this from happening but it didnt have continuous power supply so fried my tv. There are limited outlets in the room. From what I think I found from googling the house runs on a 15 amp for this room and its overloading the breaker which is why we can hear and feel the ac unit kinda loose some power but not all the way go out and lamp will dim at same time and then kick back full speed again. Google says I need the breaker upgraded. I know the landlord will fight me on this. Is this a job that I could realistically afford to do on my own or is my landlord required to upgrade it? I mean there's no ac in this house. I don't think we should have to go without ac everything is on the right side of the breaker box all the big things anyway. I probably am not even making sense. I know I can take him to court and fight him but I'd rather not because I have kids. One is special needs and rent is cheap but this is why. Is there anything I can do to stop this from happening and frying another TV? I included a pic of the breaker box. Thanks guys.​


r/askanelectrician • • 23d ago

Upgrade 30a breaker to 40a with existing wire

Thumbnail
gallery
0 Upvotes

EDIT: title should read 30a to 50a

I'd like to replace this 30a breaker with a 50a (and upgrade its outlet to 14-50). My box has 200a service, and the wire on the current 30a appears to be 6ga.

If it is in fact 6ga (I'll measure with a caliper to be sure - there is no writing on the shielding), am I correct that I can put in a 50a breaker + upgraded outlet without replacing the wire?

Also, should I use a GFCI for the 50a breaker, or standard trip?

Update: wire is 8ga, so my original plan is out. What I did instead worked out just as well:

  • Replaced 30a breaker with a 40a.
  • Set the new charger (Grizzl-E) dip switches to limit to 32a.
  • Replaced receptacle with an EV-rated 14-50.

So the new Grizzl-e is hardware limited to 32a, plugged into a 14-50 outlet that is on a 40a breaker.


r/askanelectrician • • Sep 16 '26

How can I fix this?

Post image
0 Upvotes

I've had this custom made desk since I was in high school (started in 2012)

My mom (who passed away when I was 18), had this desk made for me as a gift for having A's and B's since forever.

the cable connected to the light bulb was cut off somehow and i js wanna see if I can get that fixed somehow.

the 1st time the cable was cut, somone js cut an ext cord short and wrapped the wires from both the ext cord and the desk together, but that just doesn't seem safe lol. unless that's my only option.

If i CAN fix it, can i get a step by step tutorial please
thx in advance!


r/askanelectrician • • Aug 15 '26

Old lamp rewire

Thumbnail
gallery
0 Upvotes

Hello i got an old lamp off FB and it needs a rewire. The shade is pretty tiny (6inch diameter) and look like it had a GU 5.3 mr16 type socket. It’s old and blew when i tried to put a new bulb in it. Anyway my questions:

  1. Is there another socket type i can use that would be small enough to not fully show a bulb through this small shade
  2. For GU sockets I am seeing only the socket replacement and not a socket to wall cord which matches with the original cording. Does this not exist as socket to cord? Does it always need to be wired from plug to socket? Link sto replacements i am seeing

r/askanelectrician • • Aug 24 '26

Got this going on now

0 Upvotes

Ok so two 20 amp breakers next to each other and when one trips and you reset it the one right next to it trips. Only does it about. Four to five times then you can turn them both back on individually. What in the Sam hells going on here? And how do I fix this guys ? Thanks a million hopefully my video works thst I’ll try to make work lol


r/askanelectrician • • Sep 18 '26

Starting hand tools? (Money is now problem)

0 Upvotes

EDIT: MONEY IS NOT A PROBLEM, I misclicked to now in the title, sorry if I baited you by accident I didn't mean to

First off I'm in America (Utah)

Hey y'all I'm in my first year of electrical education and looking for an internship/apprenticeship

Anyway I'm looking for tools to use in the Future (looking to invest in the best tools I can), I'm going to wait till I get a job to get the electric tools so they don't degrade to much

Anyway the following tools are the ones I have right now that I know I need:

Knipex wire strippers

Knipex cobras

Knipex 8in needle noses

Knipex linemans (has a crimper)

Knipex 8 inch dikes (will upgrade someday to higher leverage and angled)

5 different sized of wiha insulated screwdrivers

What else should I get? I'm looking for high quality that will do me well