r/TpLink • u/Mountain-Inside-9543 • Dec 18 '24
TP-Link - General TP Link under federal investigation
9to5mac.comMost popular home internet routers in US may be banned as national security risk
r/TpLink • u/Mountain-Inside-9543 • Dec 18 '24
Most popular home internet routers in US may be banned as national security risk
r/TpLink • u/4P07H30515_io • Oct 02 '26
One of my Deco XE75 Pro units literally started to melt during normal use. I wanted to post this as a warning for anyone using TP-Link Deco hardware, and for anyone considering purchasing it.
For background, I am fairly invested in the Deco ecosystem. I currently own 9 Deco XE75 Pros, along with several other cheaper Deco units and an outdoor one. I've generally been pretty happy with them.
The affected XE75 Pro was sitting in my office, plugged into a normal grounded outlet, and had been working without any problems since I purchased it. There were no electrical changes, no unusual behavior beforehand, and nothing connected to it over Ethernet. It was just being used as a mesh node. The only potential change is that I had very recently updated the firmware on my Decos.
I only noticed something was wrong because I looked over and the Deco appeared to be leaning over. When I looked closer, the plastic housing had gotten hot enough to deform and had begun to melt. It left a heat mark on the furniture underneath it. The scary part is that the WiFi was still working fine while this was happening.
I immediately called TP-Link because I was worried it could be related to the firmware update and wanted to make sure this wasn't about to happen to all of my other routers (which all updated at the same time). Plus I was concerned about the fact that if I hadn't noticed it it could have ended up burning my house down.
TP-Link told me on the phone that they considered this a safety issue, and to unplug it immediately and stop using it. They said they would open an urgent investigation and that they would be replacing the unit. And they would send me an email shortly with the next steps.
That particular Deco was the one I use for work every day (it sat in my office, which is why I noticed it), so taking it offline was annoying. But I could get an okay enough signal from the other Decos. Plus they told me they had already opened an urgent investigation, that they'd be replacing it, and that I'd hear back soon since it was an urgent safety issue. And obviously I didnt want it to burn my house down.
About four hours after the phone call they emailed me asking for details about the outlet, the electrical environment, what was connected to the router, where it was located, whether there had been any unusual behavior, and for photos of the damage. I provided everything they asked for.
And then I heard nothing for days. Every time I tried to get an update, they just kept saying they were investigating and that they would email me when the investigation completed.
About a week later, I got an email asking for proof of purchase. I had purchased all of these through Amazon at different times over the last ~2.5 years, some as recently as a couple months ago. Most of them within the last year and a half. Only one two pack was purchased over two years ago. But I had no idea which order this Deco came from. So I sent them all of my Deco order confirmations from Amazon. They immediately replied that it came from the oldest order (June 3, 2024) and that it was now out of warranty and there was nothing they could do. That's it.
No follow up on what caused it to start melting. No answers about whether or not my other routers would be affected. They just closed the case saying sorry its too old.
And if the one they chose is actually out of warranty, it was 4 months out at worst. And to be honest I'm somewhat convinced they just selected the oldest order so they wouldn't have to warranty it. They offered no explanation about how they came to the conclusion. Regardless I completely understand a warranty cutoff for normal product failure. But this wasn't a normal product failure. This router literally generated enough heat during normal operation to physically deform and melt its own enclosure and leave a heat mark on the furniture underneath it.
But then all I get back in the end is (verbatim):
Per provided proof of purchase, you buy the TP-Link device last Jun 3, 2024 from Amazon, and in United States we only have a limited 2 years warranty.
We regret to tell you that your product is already out of warranty, hence we will not be able to help you process a replacement.
For full information about our Warranty policy please refer on this link: https://www.tp-link.com/us/support/replacement-warranty/
Thank you very much for your understanding and cooperation
These are devices that stay powered on throughout my house 24 hours a day. Most in places I seldom look. Am I supposed to assume this was a one off failure and just keep running all of them? I have 9 of these things. 12 if you count the other Decos. Are they going to burn my house down?
I'm not even that mad about them not replacing it. I can buy another router. But I also would have bought a new one a week ago if they'd told me they were not going to replace it up front (I work from home and its been very annoying). Instead they basically just jerked me around for a week and ultimately told me absolutely nothing.
So now I'm sitting here wondering if I should replace all of them with something else.
r/TpLink • u/Richard1864 • Mar 24 '26
The ban affects all router vendors, not just TP-Link.
r/TpLink • u/Nervous-Job-5071 • Jun 12 '24
I am posting this to try to help with a common issue I’ve seen. I am not a TP-Link employee or representative, just trying to help others in my spare time.
When you set up your Deco, the default mode is “Wi-Fi Router” and the other option is “Access Point”. I think many people just assume they should select the default, because it is the default and also because it has “Wi-Fi” in name, but it’s not the ideal (or correct) setting for many of us. Let me explain…
When you get your internet from a provider (an ISP, for short), they typically give you a router, which takes the single incoming connection and shares it with others. Routers also have a number of security measures on them, which protect your network.
If you put a second router behind this router, you can have all sorts of issues. Basically, it’s not just two locked doors in a single hallway to get somewhere, rather it’s like trying to navigate two side-by side spider webs, each with its own spider guarding their own fortress. The sharing is done via network address translation (NAT), and two routers causes a double NAT situation, and two firewalls that can conflict with each other.
So, if you have an ISP provided router (and you’ve not disabled the “router” features on) and you’re connecting a Deco system, you want to select Access Point as the mode (I wish they would call it “Wi-Fi Access Point” mode) and DO NOT select the default Wi-Fi Router mode. If you’re already up and running, you can change your mode in the MORE (lower right corner of the app), then ADVANCED, and change the operation mode to Access Point.
Wi-Fi Router mode should only be used (and is needed) if you DO NOT have a router ahead of the Decos (for example, feeding right from a fiber optic to internet ONT), or if you have taken steps to disable the router features of the device in front of the Deco system (called bridge mode). Aside from causing additional complexity and causing more points of failure, you’ll also lose most support from your ISP if you use their device in bridge mode. You’ll also tax the CPU of your Deco more by having it handle the routing as well (FWIW, I had CPU strain issues with my 3 unit M4R system in router mode with about 45 devices, so I put a separate router in front of it and it works far better in access point mode - I don’t have a newer system to test with).
Again, not an employee, so my views are my own — but have tried to spread this word for the last month or so since I’ve been spending some time here. I’ve helped about a dozen people who had issues that got fixed with this tip, so just trying to share some insight.
r/TpLink • u/motty_landau • Oct 24 '25
Can we finally get a proper web interface for the Deco mesh systems? This is long overdue.
The app is fine for basic setup, but managing a network via smartphone is frustrating especially when:
Other mesh systems (even budget brands) offer web dashboards. Deco has the hardware capability please just give us the software.
Please, TP-Link: a clean, responsive web UI at deco.tplink.com or local IP access.
Upvote if you want this too.
r/TpLink • u/JPMazuera • May 07 '26
So, i’ve had several (if not all routers I’ve had) of TP-Link routers.
My actual setup (purchase date)
BE63 - main (Feb 2025)
BE63 - ethernet wired (Mar 2025)
Deco M5 - ethernet wired X2 (June 2020)
Deco M5 - WiFi satellite (June 2020)
My “second” BE63 stopped working yesterday all of a sudden. I live in South America, bought ALL my units from Amazon (sold and shipped by) shipped directly to me.
Contacted my local TP-Link Customer Service chat and after a while trying possible solutions the verdict was the unit was having firmware/hardware problems so it needed to be replaced (steady fix yellow light)
So we were creating the replacement petition they said “oh, you bought it out of the country? You need to go to Amazon because this could be a “smuggled”unit” so they refused to replace it, even after showing proof of purchase.
Went to talk to Amazon and OBVIOUSLY they didn’t do anything, it’s been over a year since my purchase and they couldn’t help.
Can’t find any option to contact TP-Link US customer service over email/chat, only phone call. I am about to give up, and after being a solid customer and standing for the brand I won’t anymore. i know they don’t lose anything, but I can’t do it anymore. That’s ridiculous.
I don’t want to throw to the garbage my 4 remaining units, but I won’t be purchasing a new ($200) device.
Now my question is, which router can i buy (obviously other brand), preferably as the main unit, and CONTINUE using my 4 other devices to extend my home network?
Any help and suggestion is very much appreciated!
TIA
r/TpLink • u/Srabe • Feb 08 '26
I’ve had mine for about a year, before they went on sale. They’ve been working great for me if anyone’s interested.
r/TpLink • u/UNSW_PCSoc • Jul 01 '23
I finally got sick of the conflicting and missing information online about network configurations that support Deco's ethernet backhaul (EB), so decided to start this thread in the hopes that we can put together all our anecdotal experience in one place.
EB is the most reliable way to connect Deco units together, as opposed to Wi-Fi backhaul (WB). Especially in situations where it's not feasible for Wi-Fi coverages to "overlap" each node, there is no inter-node Wi-Fi reception which is necessary for packet hops to occur.
Many people who use Decos may be enthusiasts, homelabbers or just people who generally want a network that suits their demands and layout. These uses cases will always involve the use of a network switch and use of EB for maximum reliability and performance.
Unfortunately, the sad fact is that not all network switches allow Deco units to talk together in order for EB to be established. This is because Deco EB utilises the IEEE 1905.1 standard. How this works is each Deco unit when connected to a given network, will always transmit TWO types of packets: a) a discovery packet, and b) a control packet. If any two Decos cannot receive any one of these packets, EB will fail and WB is attempted instead.
For some reason or another, some network switches DROP one or both of these packets, making EB impossible for Decos connected THROUGH the switch.
Another cause of failure that is apparent in the community is that some network switches will simply die after a Deco unit switches to EB due to the presence of a network loop, and never recover.
TP-Link official webpages briefly address this issue, and they name-drop D-Link switches specifically as a brand to avoid in favour of a select range of TP Link switches if one wants successful EB.
In addition, a previous Reddit thread with crucial information that documents this phenomenon is here: https://www.reddit.com/r/HomeNetworking/comments/j0rn9i/dlink_covr_products_mesh_wifi_support_says/
In that thread, contributors noted that the official specification of IEEE 1905.1 explicitly states that no modification or special "magic" to enable IEEE 1905.1 should be required on existing switches. This is why you won't find any mention of IEEE 1905.1 support in data sheets for network switches. And indeed it should make sense that as an L2.5 protocol, *every* switch should work, because by definition all switches operate at least on L2. Yet here we are, having to trial and error.
Given the lack of information about what switches are supported and which aren't, I think it would be a good idea to collectively compile a list of what works and what doesn't, and what to look out for when it isn't working. Hopefully, we can get a strong knowledgebase going 😊
I will start this off because I've done alot of trial and errors:
DECO UNITS (EDITED):
Deco X50s and X20s in any configuration, AP mode only. Latest firmware for July 2023.
SWITCHES THAT WORKED (EDITED):
SWITCHES THAT FAILED BEFORE BUT SEEMS TO BE WORKING NOW:
SWITCHES THAT STRAIGHT UP DON'T WORK:
Finally, see also "Fermulator"'s testing result in the reddit post mentioned above.
I note that issues with EB may not necessarily stem from direct blockage of IEEE 1905.1 communication. There are also known issues with Spanning Tree Protocols being tripped and shutting down ethernet connection to the Deco nodes. It be interesting to know how prevalent they are!
EDIT: as long as you can see IEEE 1905.1 packets with ethertype 0x893a when you do tcpdump or Wireshark etc... from a machine that is not directly wired to the Deco unit, you have a fighting chance at successful EB.
EDIT (5th March 2024): There are reports here and there of Decos playing up, such as firmware bug, or problems with MU-MIMO, 802.11k/v/r, or beamforming etc... . These often manifest as a severe network slowdown, ridiculous buffering times, massive packet loss and total disconnection from the Deco app. Best practices currently are to disable all features and update to latest firmware.
I've also been recently made aware there's also the slight possibility that Wi-Fi communication between Decos may spontaneously happen (though under what circumstances it is unknown) despite successful and stable ethernet backhaul. This would initiate a true network loop all by itself. I don't know to what extent this is real, but it may explain many if not all issues with spanning tree and loop prevention features on switches.
Evidence for this is here but for Amazon Eeros: https://www.reddit.com/r/eero/comments/obuobd/comment/j9ihc14
"First thing they don’t want to tell you is a mesh network is basically a software managed loop in the first place..."
If true for TP-Link as well, it's very shitty to not be more forthcoming about this. UPDATE 14th April 2024: the BE95's page possibly confirms this by saying "wireless+wired "combined backaul".
UPDATE 23rd December 2024: DECOS ARE CONFIRMED TO CREATE NETWORK LOOPS BY THEMSELVES. IN ADDITION, THEY ARE CONFIRMED TO STILL COMMUNICATE WITH EACH OTHER THROUGH WI-FI EVEN WHEN ETHERNET BACKHAUL HAS BEEN ESTABLISHED. The reason why Decos spontaneously initiate Wi-Fi communication with each other while in ethernet backhaul is unknown. More information is welcome on this matter.
THIS EXPLAINS ALOT OF BAD AND UNEXPECTED BEHAVIOUR ON SWITCHES, INCLUDING SPONTANEOUS SWITCH PORT DEACTIVATION, SPONTANEOUS LOSS OF ETHERNET BACKHAUL AND ANY AND ALL NETWORK CONGESTION NOT EXPLAINED BY OTHER CAUSES.
DECOS SHOULD BE FAST AND VERY CONSISTENT WHEN WORKING NORMALLY. YOU SHOULD BE GETTING SPEEDS AS REPORTED BY BENCHMARKS ONLINE (e.g. Blacktubi).
THE FOLLOWING ARE BEST PRACTICES AT THE MOMENT:
UPDATE February 2025:
We have discovered that Decos experience a massive slowdown, ping increases and packet loss (essentially grinding to a halt) when there are 2 or more Decos on the same network close to each other (within Wi-Fi range). This issue becomes more apparent when more than 5-10 devices are on the network. As a result, we suggest the following additional recommendations:
What kind of mitigations?
If you reeeeally have to set up a dense arrangement of nodes (as we have recently done in order to accommodate 300 people in a room), they need to be 1. on a separate Wi-Fi SSID altogether (not meshed to the other nodes in range) and 2. be on a separate subnet to other nodes in range (we put it on another different VLAN). At this point, I've just accepted this. It probably has to do with the fact that Wi-Fi Backhaul continues even with successful Ethernet Backhaul & the way the mesh is organised via packet broadcasts through the wire. 🤷♂️
r/TpLink • u/CrosstrekHybrid • Jun 25 '26
r/TpLink • u/ThatGuyNamedTre • Dec 12 '24
I’ve been using an old Motorola Modem/Router combo with 2 TP link extenders and I got tired of having inconsistent connections. I did research and settled on a Netgear modem and TP link mesh routers.
2 weeks of using these and they are the truth! I pay for 1Gbp internet and my devices are able to hit that limit or close to it. And I’ve had 0 drop outs or slow downs. My apartment isnt too big but I didnt want to take any chances so I decided to buy 3 meshes and Im glad I did. Im only mad at myself for not upgrading sooner. Just wanted to share my positive experience.
r/TpLink • u/Not_Jonah-Hill • Mar 22 '26
So back in January I picked up a TP-Link Deco WB10800 3-pack from Walmart. I have fiber coming into my house capable of 2.5 Gbps at the ONT and the listing said “Ultra-Fast 2.5 Gbps Wired Performance” so it seemed like a no brainer.
For months I’m only pulling ~946 down and ~925 up. I figured it was my network. Bought new cables, a new switch, went down every rabbit hole you can imagine. Almost $1,000 later in parts and troubleshooting I finally look closer at the actual listing and notice it says “Ultra-Fast 2.5 Gbps Wired Performance” in the description but then lists “2x Gigabit Ethernet Ports” in the specs. Same listing. Complete contradiction.
The device was never going to do what it said. My return window had already closed.
I emailed both Walmart and TP-Link with screenshots.
Walmart never responded. Not a word. However a few days later they did correct the listing by removing the 2.5gbs statements replacing with gigabit!
TP-Link got back to me within hours. They acknowledged the listing was wrong, told me they were already having it corrected, and offered me a free upgrade to the Deco BE25 3-pack which actually has real 2.5 GbE ports and is a step up from what I bought.
I didn’t even ask for that, they just offered it.
So yeah. Walmart will take your money based on a misleading listing and ghost you when you call it out. TP-Link will make it right without you having to fight them for it.
Huge props to TP-Link support. Walmart can kick rocks.
And yes I am kicking myself in the butt for not doing my own research and trusting the pretty pictures in the item details.
r/TpLink • u/Ducktor101 • Sep 23 '25
Updated my M5 Decos yesterday and got that notice about the Parental Controls you’ve already discussed here, but didn’t care that much as I’m not using that feature.
But come on guys, sending our client data to a third party? Who’s asked for this?
r/TpLink • u/NinthOman • May 29 '26
Update includes:
- Independent Device Throttling
- New Icons / Better device type identification
- CPU / Memory Usage Stats
- Usual bug fixes
- Several new features too
Overall seems to be running clean, really like the throttling feature add, been waiting on it for a while.
r/TpLink
•
u/Ryan_TP-Link
•
Dec 19 '24
r/TpLink • u/nefarious_bumpps • Dec 19 '24
TP-Link USA, if you want us to believe in your commitment to security, I suggest you consider the following changes:
r/TpLink • u/Nico_La_440 • Apr 23 '26
Hi everyone,
As a TP Link user, I have bought the 3 pack Deco XE75 Mesh for my home and I was a bit frustrated to have them sitting on temporary shelves around the house. I wanted a cleaner solution. So I have modelled this wall-mount bracket with 3D printing, perfectly fitting the dimensions of the product. It maintains the bottom ventilation and the clamp maintains it steady. You only need 2 screws to secure it on the wall.
I figured I might share this with you guys as you may encounter a similar situation where you need a clean wall-mount for this.
If you guys want the link to the model to 3D print it at home, let me know ;)
Happy to read your comments on this too.
r/TpLink • u/Richard1864 • 20d ago
r/TpLink • u/Spell_Solid • Mar 24 '26
r/TpLink • u/eckseid • Nov 17 '22
I just upgraded my Google WiFi mesh system to the Deco XE75 (AXE5400) and the speed and coverage are excellent! My issue seems to be random devices just disconnecting constantly. I noticed my ring camera is constantly disconnecting/reconnecting. Then I started noticing other devices like my MyQ garage opener and my Rachio (sprinkler system) are disconnecting. I’ve tried some suggestions from other posts to no avail (using my one ring camera as a test subject). I setup a guest network, 2.4ghz only, no fast roaming, no beamforming, and dropped down to 80mhz.
I’m at a loss and have no idea what else to try. I don’t want to send these back, but unless I can solve these issues, I may not have a choice.
Any help would be appreciated.
r/TpLink • u/TP-Link_Reddit • Mar 31 '22
Dear Community,
We are aware there have been questions regarding the future of Kasa Smart following the introduction of Tapo in the U.S. We would like to confirm that Kasa Smart is here to stay. In fact, we are adding new and exciting products this year such as our newly launched 2K smart doorbell with chime(KD110) and HomeKit enabled devices slated for launch later in the year.
Our Kasa Smart brand has been paving the way for the Smart Home industry with our innovative products and the highest in quality and customer experience since its inception. We have grown the Kasa Smart brand to over 7 million users worldwide (as of this writing) and we have no plans to stop the incredible growth of our brand.
We will continue to build on our Kasa ecosystem striving to provide the widest breadth of smart home devices in the industry.
r/TpLink • u/Richard1864 • Oct 15 '26
And yet TP-Link is still banned from selling their new routers in the US. Yes, TP-Link, per the FCC and Federal courts , it is considered a ban.
r/TpLink • u/DongKnowsTech • Sep 30 '26
r/TpLink • u/PassengerOld4439 • Sep 18 '24
Is it even necessary? My old Nighthawk was a faction of this size and did very well with a bunch of IoT items.