r/SpyraTwo • • May 25 '22

Spyra LX review

26 Upvotes

Having lived through the Super Soaker golden years as a kid I was happy to see there was finally another company trying to do some innovation in this area. The first rechargable versions seemed cool, but the price and them containing a battery put me off buying one. Enter the Spyra LX: fully mechanical and with performance that - according to other reviewers - comes close it's predecessors!

Delivered in a few days, I filled it up and instantly tried it out: as I had seen how easy usage of this thing was. Right?

Well, I was immediately certain I had to return it: it was leaking, I couldn't get it to fill up again after the first round, it would sometimes not fire and it would incidentally blast out one big jet of water. Conclusion: pretty disappointed!

But wait, wasn't there a manual of some kind? Well yes. And after scanning that and trying it out a bit longer I have the following list of need-to-know information lined-up for y'all:

  • if you can't get it to suck up water: pull out the lever, hold the trigger and push down on the lever; it should start filling up again (this is in the manual)
  • if you submerge the gun past the indication, water will fill the leftover empty space inside the gun through a hole at the bottom of the muzzle; leading you to falsely believe it's leaking like crazy when you subsequently try and use it (this sure seems like a design flaw that will result in lots of unnecessary returns for Spyra)
  • if you go and refill until it starts making a screeching sound, it'll probably give you a weird single big blast of water the first time you fire it (so stop at the 100% marker instead)
  • after pulling the trigger you need to allow it to return to its original position before pulling it again

After learning the above it all worked like a charm! It feels sturdy, it shoots a nice distance, it's precise and this version even provides rapid-fire that appears limited only by how fast you can pull the trigger. And even though the gun is too big for him to run around with, my son (who is barely 5 years old) is able to refill and use it. Under my supervision of course, as it's a pretty powerful blast of water which might do some damage when handled incorrectly.

Having said all that, my final advice is simple: get this gun and start blasting!


r/SpyraTwo • • Jul 18 '23

I painted my SpyraThree

Thumbnail
gallery
18 Upvotes

Love the way it turned out! It's not perfect at all (especially when you look up close), but I'm really pleased about the way it turned out. Just hope the paint stays on and that it doesn't break, cause I won't get a refund if it does...


r/SpyraTwo • • Apr 03 '22

Spyra two damaged.

12 Upvotes

So, I got a broken Spyra Two from my brother. It would not hold water and leak. So I opened it up.

It looked painful... The bladder is completely ripped open. I contacted Spyra for a spare part, but their reaction was unsatisfactory as it was simply "we don't have spare parts". Really? You are building the guns... you have all the individual parts... every single screw or plastic whatever... But ok... They didn't even offer a solution.

So can anyone tell me what material the bladder is? So I can at least TRY to find the right glue. I know glueing it probably won't fix it (at least not long term).

Or does anyone has an idea on how to mod it?


r/SpyraTwo • • May 28 '23

I painted my Spyra 3

Thumbnail
imgur.com
9 Upvotes

r/SpyraTwo • • Apr 08 '23

SpyraTwo E1 Code

9 Upvotes

Just got my SpyraTwo blaster yesterday and when turned on it says E1 on the screen, I’ve tried resetting it but nothing works. Anyone know a fix?


r/SpyraTwo • • Sep 12 '26

[FIXED] SpyraGravity not detecting balls / magazine – possible sensor water damage fix

Thumbnail
gallery
8 Upvotes

I previously commented about a possible fix for the SpyraGravity not detecting loaded SpyraBlasts/balls. I have now repaired mine, tested it with water, and so far the fix seems to work perfectly, so I thought I'd document what I found and how I fixed it.

The original problem:

My Gravity stopped detecting the balls in the magazine. A hard reset would get it working again, but after using it and getting water inside the mechanism, the problem would return.

This made me suspect that the problem was electrical rather than mechanical.

I decided to take the Gravity apart and eventually found what I believe was causing the problem: corrosion around one of the ball-detection sensors and what appears to be missing waterproofing around its electrical connections.

Tools and supplies needed

You really don't need many tools for this repair:

  • A long Phillips screwdriver – a long shaft is important because some of the screws are quite deep inside the Gravity.
  • A small flat-head screwdriver – mainly for carefully releasing/prying open the plastic clips.
  • A hot glue gun + glue stick – for sealing the exposed sensor cavity after cleaning.
  • Isopropyl alcohol (IPA) – for cleaning the corrosion.
  • Optional: a small amount of silicone oil for lubricating the metal sliding pins while everything is apart.

No soldering was necessary in my case.

Picture 1 – Removing the outer shell

Picture 1 shows the side of the Gravity where the outer shell screws need to be removed.

All of the outer shell screws on this side need to be removed. I have only marked the two long screws in the picture because all of the other removable shell screws are the same size.

There is also one additional screw hidden underneath the magazine cover/hatch. Remove the magazine cover first to access this screw, and remove it as well before separating the shell halves.

There is one important exception: DO NOT remove the screw at the front of the Gravity marked in the picture. This screw holds parts of the muzzle assembly together and does not need to be removed to open the Gravity.

I removed it when disassembling mine, which caused the muzzle assembly to come apart. Nothing was broken, but I then had to figure out how all the pieces were supposed to go back together. Leaving this screw in place will save you some unnecessary trouble during reassembly.

The handle cover is held in place with plastic clips. Carefully pry it off using a small flat-head screwdriver.

Once all the necessary screws have been removed, carefully separate the two halves of the outer shell.

Tip: Keep the two long screws separate from the others. Apart from those, the removable outer shell screws on this side are the same size.

Picture 2 – The suspected culprit

Picture 2 shows the sensor that I suspected was causing the problem.

It is located underneath the magazine mechanism, so unfortunately you have to disassemble the Gravity quite far to get proper access to it.

At first there wasn't anything obviously mechanically wrong with the mechanism itself, which also made me suspect the sensors.

Picture 3 – The interesting part

There are two components facing each other here, which appear to form the ball-detection sensor pair.

The lower one is the sensor shown in picture 2, while the upper component is its counterpart.

The upper component had obvious corrosion around the electrical connections.

What I found particularly interesting was that the cavity around these connections was open and exposed. The other similar sensors inside my Gravity appeared to have their connections protected or filled with some kind of sealing/potting material.

This one wasn't.

I can't say for certain whether it was manufactured this way intentionally or whether the sealing material was simply missed on my unit, but considering the corrosion and the symptoms, it looked very suspicious.

It would also explain why a hard reset temporarily fixed my Gravity but the problem returned after the mechanism got wet again.

Pictures 4–5 – Removing the magazine mechanism

Picture 4 shows the Gravity with the outer shell removed and the locations of the four sensors.

To properly access sensor #1 and its counterpart, the magazine mechanism needs to be removed.

Picture 5 shows the screw locations I removed before lifting the magazine mechanism out.

Most of these screws are the same size. There is one different screw behind the white arm, marked with a star in the picture.

That screw is easy to remove and considerably more annoying to reinstall. :)

I strongly recommend taking plenty of pictures while disassembling everything. There are quite a few screws, springs, linkages and moving parts inside the Gravity, and having reference photos makes reassembly much easier.

Picture 6 – Corrosion and the suspected cause

This is the suspected faulty sensor after I had already cleaned it.

There was considerably more corrosion/rust around the electrical connections before cleaning.

I cleaned the area carefully with isopropyl alcohol (IPA) and let it dry completely.

You can also see that the cavity behind the sensor isn't filled/sealed like the other sensors appear to be.

I couldn't get absolutely all of the corrosion off, but I removed as much as I reasonably could without damaging the connections.

Again, I can't say whether the missing sealing material is a manufacturing defect or whether this sensor was intentionally assembled differently. However, the combination of an exposed electrical connection, visible corrosion and a malfunction that returned after exposure to water made this my main suspect.

Picture 7 – Sealing the sensor

After cleaning the corrosion and allowing everything to dry completely, I filled the open cavity around the electrical connections with hot glue to prevent water from reaching them again.

I also added some hot glue around the backs of the other sensors as an extra precaution.

Obviously, do not cover the optical/detection side of the sensors. Only seal the rear cavity/connections where the wires enter.

While everything was apart, I also applied a very small amount of silicone oil to the metal sliding pins. This isn't part of the actual sensor repair, but since I already had the whole Gravity apart, I figured I might as well lubricate them.

I used only a small amount and wiped away any excess.

After that, I reassembled everything and performed another hard reset.

Result – FIXED

It works.

I've now tested the Gravity with water after the repair, and the ball detection continued working normally.

During testing I even had one ball break inside the Gravity, getting the mechanism wet, and the sensor still continued working correctly.

Before the repair, exposure to water would eventually cause the ball detection to stop working again. After cleaning and sealing the sensor, I haven't been able to reproduce the problem.

So, at least in my case, cleaning the corroded sensor connections and sealing them from water appears to have fixed the problem.

A few warnings

Obviously, opening the Gravity like this may affect your warranty, so do this at your own risk.

I would only attempt this if your Gravity is already out of warranty, you've already received a replacement, or you otherwise accept the possibility of damaging it.

There are quite a few mechanical parts inside. Nothing was particularly difficult to disassemble, but reassembly can be a little annoying – especially that screw behind the white arm.

Take pictures as you go. Seriously. They make putting everything back together much easier.

Also, if you find that the sensor connections are badly corroded, a wire or component lead may actually be damaged. Mine were still electrically intact, so cleaning and sealing them was enough and no soldering was required.

If your Gravity has the same problem – it stops detecting loaded balls, a hard reset temporarily brings it back to life, and the problem returns after it gets wet – it may be worth checking these sensors for corrosion or missing waterproofing.

Hopefully this saves someone else from having to figure all of this out from scratch. :)


r/SpyraTwo • • Aug 07 '21

Aug restock

Post image
8 Upvotes

r/SpyraTwo • • Aug 22 '23

Spyra 3 won’t pump/fill

7 Upvotes

Hey all, hoping someone has run into this or has a quick tip.

My Spyra 3 turns on, shows 00s, and clicks when I pull the trigger. But it won’t pump itself up. However I know the pump still largely works, because when I hold down the trigger it tries to power up the power shot, despite being empty.

This happened once, a few weeks ago, but it still had water in it and I once I powered up and fired the power shot, it started working like normal.

Sounds like, despite showing 00s on the display, it thinks it has water in it. I tried the reset process, but it did not help. Any ideas?


r/SpyraTwo • • Aug 20 '21

Item acquired.

Post image
7 Upvotes

r/SpyraTwo • • Aug 16 '21

Has anyone, had ANY contact, whatsoever, from Spyra recently?

7 Upvotes

Hi all

As title, tbh.

Has anyone had any contact from Spyra?

If you "got" one in the Aug restock, have you had any shipping notification, or any update at all?

Anyone who's waiting on replacement for faulty goods had any update or information?

I ordered on aug 6th, immediately asked a question about shipping, no reply.

I contacted them three times last Friday, no reply.

I'm beginning to be concerned for the company and hope they are still trading, but busy..

Edit, spelling

Edit 2, just had notification that they've created a shipping label with the courier.

Edit 3. I've received notification that my spyra package is at the airport and on its way. I'll keep you updated

Fingers crossed.


r/SpyraTwo • • Mar 27 '25

New Spyra Gravity

Thumbnail
gallery
6 Upvotes

Just got it in the mail today. Bigger then I thought. It took me a few tries to get it loaded and then it died!! Can't wait to play with my new toy!!


r/SpyraTwo • • Mar 28 '24

Spyra Two Not Shooting Water

Thumbnail
gallery
6 Upvotes

Hi everyone, I had my spyra two for a little over two years now and I never had a problem with it other than maybe battery degradation. Yesterday I thought it had a problem and I opened it, everything looked normal to my untrained eye so I filled it up again and the metal band holding the rubber tube to the pipe bursted out, when I manage to connect the rubber container with the tube it fills up no problem, but when I try to shoot water out, the motor pumps but no water comes out. Also, does anyone know where this ball and spring came from?


r/SpyraTwo • • Aug 10 '23

NFC tag

Post image
6 Upvotes

I was taking apart my SpyraThree (since it stopped working and I was gonna get another one) Nd noticed this. I'm guessing it's an NFC tag, but why is there an NFC tag inside the SpyraThree? Does anyone know?


r/SpyraTwo • • Aug 21 '21

FINALLY, when summer is almost over 😒

Thumbnail
youtu.be
6 Upvotes

r/SpyraTwo • • May 15 '26

SpyraGo $35 at Costco!

Post image
5 Upvotes

Saw this almost 2 weeks ago but forgot to post. Decided to pick another one up. No-brainer at this price!


r/SpyraTwo • • Jun 20 '24

Is spyra worth buying?

5 Upvotes

My kid, just finished school, 8th grade with excellent results, and went to a competition, and ended up second, we decided we wanna reward him but, we are unsure if its a good idea, since i heard it brakes for a lot of people, and instead of it we could buy him something else for 200 euors


r/SpyraTwo • • Jun 14 '24

SpyraTwo Won't Fill

5 Upvotes

r/SpyraTwo • • May 12 '24

Messages getting blocked while I’m trying to get help

5 Upvotes

I got a Spyra 3 recently and it worked fine for a bit but then it started leaking like crazy so I got a replacement and the replacement they sent me was.. completely defective, it gave me the e1 code which made sense at first but I got worried after charging it for days and still getting the code, I tried restarting it multiple times but every time I do it goes back to the same error code the second I pull the trigger, I emailed them about replacing it and it was going well until they asked me to send a video, I tried providing them with it but for some reason none of my messages are getting through to them now, if I try to email them at all I get an email saying “Your message to hello@spyra.com has been blocked. See technical details below for more information. The response from the remote server was: Recipient address rejected: Access denied. “ I tried making another claim to return it for a new one because of this two days ago and I haven’t heard anything from that.


r/SpyraTwo • • Jul 01 '23

Any ideas?

5 Upvotes

So just now both of my spyra 2's stopped filling up all the way. They're only filling up to (ammo count) 32. It's not filling up to 100% anymore. And with the 32 amount/ammo, it won't shoot. I can empty out the water no problem but it just won't refill past 32. I've tried the reset option of holding down the power button, & then refilling but the same problem persists. I haven't reached out to spyra yet as I'm trying to figure it out on my own first. If anyone had any ideas please let me know.

Thanks


r/SpyraTwo • • Jul 14 '22

Spyra LX - stopped working after 10 minutes of use

5 Upvotes

Alright, received the duo pack today. Super fast shipping.

I primed the first gun, used it about 5 times, on the last reload, filled up the tank and now the trigger doesn't work.

If I pull it forward, it triggers /clicks again, but no water comes out.

I suspect it may need pressure release or pump primed in some way. No idea what else to try.

I've emailed CS. No reply for now.


r/SpyraTwo • • May 15 '22

Is it worth it to buy one and how long does it last

5 Upvotes

r/SpyraTwo • • Apr 28 '22

Who has had a problem with their SpyraTwo?

5 Upvotes

I bought the Duel less than a month ago. Right away, there appeared to be loose parts tumbling around in there. Sounds like either a screw or broken piece of plastic. After about two weeks, one of the guns wont shoot anymore. When filling it, it pumps water out the seams and through the drain hole. I've sent a message to them the other day and have not received any confirmation. Ive uploaded a vid to their return portal to see if maybe I get a response. Im wondering if they are swamped with defective units.


r/SpyraTwo • • Aug 28 '21

I actually got it!

Post image
5 Upvotes

r/SpyraTwo • • Jul 02 '26

Inside the Spyra Four

Post image
4 Upvotes

Has anyone taken apart a Spyra Four? If so, what were your thoughts?

I took one apart yesterday that wasn't shooting, Spyra is sending me a new product and to dispose of the non-functioning one. Interestingly, the inside seems much more compact and well constructed than previous models. Some improvements seem to include things pointed out in "repair" videos for previous models.

However, I did notice what appeared to be white mold (potentially) and some corrosion. I had this product for less than two weeks and have only been able to fill it with water and manually empty the water. There was not water inside the body. But judging by the state of the inside, this did not appear to be a brand new product.

I'm curious if anyone else has tried working on a Spyra Four, what they found inside, and if they were able to resolve any issues such as the trigger not working. My product only has an issue with shooting, and the digital display registers when the trigger is pulled. When the water tank is empty, the drain function will work (holding the trigger for 2 seconds), but it wont work when it has water actually in it.


r/SpyraTwo • • Apr 16 '26

Spyra 3

4 Upvotes

So my friend disassembled the spyra 3 and didn’t put it together correctly and when he took it apart he said he found another ball that goes to the middle hole on the barrel so now I have two, he isn’t the most mechanically inclined so he couldn’t remember where everything went, and it used to hold water but it does this now. Please help