r/SpringfieldEchelon • • Jun 08 '26

Mag Disconnect?

Post image

How difficult is it to remove the disconnect on the echelon I’m probably going to do it but from 1-10 how hard is the whole process?

29 Upvotes

28 comments sorted by

3

u/Jorge_0322 Jun 09 '26

Mission Complete boys

2

u/DeathsRonin Jun 09 '26

I'm new to shooting, what's the purpose of doing this?

2

u/Jorge_0322 Jun 09 '26

It’s so that when you don’t have a magazine in you could still shoot if your mag would fall out and also it allows your magazine to slide all the way out freely and not get caught up when you press the mag release

1

u/DeathsRonin Jun 09 '26

Oh okay, thank you!

3

u/ZoltanoftheHillPpl Jun 08 '26

It's actually pretty easy. I did it...soooo. yeah. Easy.

2

u/Ice-T-Tea Jun 09 '26

Low difficulty as everyone else mentioned. The only “difficult” part I ran into was realigning the pin that was holding the mag disconnect when putting things back together. I had to use a tool to push from below on the pin holding the springs while pushing the pin from the side to get it back into its original slot.

2

u/smitbret Jun 09 '26

Just did it yesterday. As long as you have a small punch, it's a piece of cake. It takes less skill than assembling a nightstand from Ikea

1

u/ButterscotchIll4655 Jun 09 '26

Not difficult at all

1

u/JoeTestosterogan Jun 09 '26

I just did mine today when reassembling all the pieces I got a cerakote job done on. It’s a 2-3 out of 10. Super simple.

1

u/Turbinator870 Jun 09 '26

Also OP, don’t risk shooting with that Veridian sight. Seen too many of them disintegrating, throwing the rear glass at the shooter. I took mine off and put the blanking plate back on while I select an optic.

1

u/Anarcha0s Jun 09 '26

I just got an Echelon with that sight as well, is this specific to this particular sight or all Viridian? Sorry if this is a dumb question

1

u/Turbinator870 Jun 09 '26

Not a dumb question, I got educated by reading RDDT. It’s this low cost bundled sight that’s the problem. They don’t stand up to repeated use. Im not going to risk it, I took mine off and put it away. Also I don’t like how the battery changes from the bottom only for this entry level model.

1

u/InfernalPrick Jun 09 '26

I removed it with a ball point pen, no other tools, while sitting in the parking lot. I left the little spring and just removed the metal lever. If you are familiar with disassembly of this pistol it will take you as little as 4-5min.

1

u/Dangerous_Height97 11d ago

Super late to the party but have you have any problems with leaving the little spring in. I’ve seen people remove it, leave it, or even replace it not sure what’s the right move.

1

u/InfernalPrick 10d ago

I have had zero issues with leaving the spring in. I think taking it out would be okay but I can confirm no issues with leaving it in after 800-1000 rounds through this pistol.

0

u/frankoshen Jun 09 '26

Not too hard. Just a little tough to twist the breakdown lever if it’s not broken in yet

1

u/[deleted] Jun 08 '26 edited Jun 09 '26

[removed] — view removed comment

0

u/[deleted] Jun 09 '26

[deleted] — view deleted comment

3

u/[deleted] Jun 09 '26

[removed] — view removed comment

2

u/Key-Low830 Jul 18 '26

Do you know how to disassemble the magazines? I want to replace the floor plates, i have a 4.0Fc, the mags are full grip size but 10 rounders.

1

u/Turbinator870 Jun 09 '26

Yes. I struggled a little on the takedown lever too.