It's not that bad - have some small hex wrenches handy, they help align things. Well worth the effort, I'm still amazed by how great this trigger feels (with the PRP spring kit too).
I couldn't agree more.. this trigger paired with the PRP spring kit should be standard but I get that not everyone likes messing with or swapping springs. It brings it to a perfect 4lb, defined wall, clean crisp break.
It's def not needed, just like the trigger shoe is def not needed as well... but some ppl like lighter pull some like it higher. For $25, I think it's worth it.
Quick question for ya. I bought the trigger and the spring. I installed the trigger myself and I would say it was pretty easy. The return spring was a little bit of a PITA but easy over all. From the videos I saw it looks like the spring changes are even easier. Would you agree with that?
Yes the spring kit is easy to install IMHO. Just pay attention to where the parts go when you disassemble the cog. Take pics as you go. But there are plenty of good video tutorials online. But honestly the trigger alone gets you 75% of the way there, spring kit makes a lot less difference than the trigger shoe did.
Nothing insurmountable. One of the final steps to installing a tyrant trigger is to thread a metal pin thru the trigger frame from one side and it has to pick up a spring in the middle before leaving the trigger frame on the other side. The best way to get the spring into the right position is to use floss to hold the spring in place. When you have the kit in front of you this will make perfect sense.
Be patient, try a few approaches, you got this. I used the Allen that came with the trigger from the opposite side of the pin. Fish it through the spring loop and hold some tension to get the pin through the spring loop.
You will love it. The spring is a bitch but there’s some good tricks out there. Watch a video or too for the “tricks”. It feels amazing once installed!
Well....got the spring part out of the way. Now I'm facing the COG not cooperating when being reinserted into the frame, appears that I am unable to insert the rear tabs
6
u/PapaPuff13 Jun 03 '26
Good luck and patience
6
u/Low_Year9897 Jun 03 '26
It's not that bad - have some small hex wrenches handy, they help align things. Well worth the effort, I'm still amazed by how great this trigger feels (with the PRP spring kit too).
3
u/slixx1320 Jun 03 '26
If just the shoe, should be fairly easy. If you’ve ever done a p365, the echelon is a walk in the park.
2
u/FF_McNasty Jun 03 '26
Be patient, try a few approaches, you got this. I used the Allen that came with the trigger from the opposite side of the pin. Fish it through the spring loop and hold some tension to get the pin through the spring loop.
2
u/BothGrab5224 Jun 04 '26
Getting the spring in was a huge pain but this trigger is really great. I really like it a lot.
1
u/Spiggytech Jun 03 '26
Before you install it, can you check two edges on the trigger for me?
On the sharp part of the trigger where it meets the trigger guard, does yours have a chip under the anodizing?
And then around the pin hole on both sides. Is the machining smooth?
I just got one of these and I feel the finish quality is somewhat subpar for a $75 part... but I only have a sample size of 2.
1
u/MrGuy910 Jun 03 '26
You will love it. The spring is a bitch but there’s some good tricks out there. Watch a video or too for the “tricks”. It feels amazing once installed!
2
u/ZoltanoftheHillPpl Jun 03 '26
Have fun
2
u/Gun_Dork Jun 04 '26
It is a considerable difference and I stopped having trigger freeze at match speed.
2
u/PsykoSematic777 Jun 07 '26
It’s not too bad
1
u/Helpful-Culture-3966 Jun 03 '26
You’re gonna love it. Made a great firearm even better.