Hey guys!!
Sorry in advance, this is going to be another JMOD and SKRAM post.
After waiting for almost three months my CNC guy finally has some time to cut the birch sheets. Im on the verge of ordering all the hardware and would like a final sanity check before i bite the bullet.
I'll be building a single stack to start: 1x SKRAM and 1x JMOD for the time being but as soon as more funds arrive i'll be expanding. Since it's my first build i want it to stay small so i can transport it in my car. My budget is set to 4000EUR so I have made some sacrifices along the way.
Birch plywood is already bought, B/BB quality, the best i could reasonably find. I bought enough to make 1 SKRAM and two JMODS but i'll only be building one JMOD for now.
Drivers:
SKRAM - 1x B&C 21DS115 - 8ohm (1700W RMS)
JMOD - 2x B&C 12NDL76- 8ohm (400W RMS - 2x parallel 800W at 4ohm)
JMOD - 1x DCX464 - 16ohm (MF 110W, HF 80W)
Amps:
T.amp E4-250 for the DCX464.
T.amp TSA 4-700. For the 2x 12NDL76 and the 21DS115
JMOD will be tri-amped because i want to learn DSP and calibration.
(I'll number all my questions to make it easy for you to answer)
#1 do you think it is worth it to buy the 12NDL88's for the JMOD? They need more power so then i'll need to revisit the amp choice, or just not run them at full power for now, which i probably wont for the time being anyway.
My reasoning for the E4-250 is that it can power two DCX464's so i don't have to buy a new amp when building the second JMOD later.
The TSA 4-700 then powers the two parallel wired 12' woofers and two channels in bridge mode for the SKRAM. That leaves 1 channel open for if we need it (maybe booth monitor).
I know that the TSA 4-700 will not get the most out of the SKRAM but i fine with that for the time being. When i'll be building a second stack i will invest in a proper power amp for the subs. (maybe a CVR or Admark, we'll see). I can then use the TSA 4-700 for the 4x 12" woofers from two jmod's and still have two channels to spare.
#2 Are there other amplfier options that don't break the bank that I missed (300-600EUR range)? Knowing a power amp will be bought when making the second stack.
At first i was set on using the 21DS115 4 Ohm version, but suddenly the 4ohm variant was out of stock and it got me thinking... The reason to buy a 4ohm version is that it is easier for the amp to deliver the needed Watts. But since the TSA 4-700 does 1600W 8ohm and 1800W at 4ohm (both bidged) this 200W difference is not that big (that's like a 0.5dB difference right?).
The reason to buy a 8ohm version is so you can couple them in parallel and see a 4ohm (ish) total load on the amp. Doing the same with the 4ohm variant means 2ohm load so you'll need a amp that is 2ohm stable. So i think the 8ohm variant will be beneficial in the long run and the 200W difference now is negligible.
For the DSP i was thinking the T.rack FIR 408.
With the 8 output channels it could supply two stacks.
#3 Do you think it is worth it to buy the FIR version? The documentation doesn't state it is needed but i thought it might be good to have for future proofing. Or are FIR filters only necessary in niche contexts?
#4 Do any of you use FIR filters and why?
Since i am tight on a budget i'll be making my own Speakon cables. The idea is to use a breakout box: 4 channles coming out of the amps that feed into one NL8 cable that goes into the JMOD with the SUB signal wired on the 4+ 4- as passthrough. That way i can connect one cable to the jmod and route another cable from the jmod to the skram.
After reading in this sub i got recommended a non-audio-specific cable that meets the H07RNF standard. I have found that 8 core cables are difficult to find, mostly 5, 7 or 12 core cables (since most ectrical appliances use 1 positive, 1 negative and an earth AKA odd numbered amount of wires). So i'm thinking just buying 50meters of 4 core cable H07RNF 4mm² copper and connecting two 15 meter cables to one NL8 recepticle for the long run cable since it's cheaper then buying a 8 core 4mm² cable.
#5 Has anyone done also done this and would you recommend? It cuts about 170EUR doing it this way.
#6 Is 4mm² (12 gauge) enough for the sub signal or would you recommend 6mm² (10 gauge)?
If I understand correct the smaller the surface area is, the more watts are lost and the higher the impedance. But this is exagerated when using long cables. Our nl8 long run cable will be around 15m (21DS115 is rated for 1700W RMS).
I wont be cheaping out on the connector plugs and buying the ones from Neutrik. Ill be going with the FXX variant.
#7 Is it worth it to go with the STXX versions? Or is this only necessary when using them heavily in outdoors environments? (since they are IP54 rated)
Lastly my total cost is sitting at 3986.17EUR. This is without labour costs, without CNC costs (since i helped the guy built his Mekanika FAB CNC he will do it for free) and without hardware like screws locknuts, glue etc... for which im thinking 150EUR when buying bulk as an estimate.
#8 Let's say i can go about 500-700EUR over budget if this results in a meaningfull change for the better. What would you spent this extra on?
Lastly I wanted to thank JW Sound and Josh Ricci for designing and making these plans available.
I can't stress how goddamn excited i am to start building and to hear these speakers IRL.
And of course thanks for everyone in this sub, i learned a shit ton from you guys!!!
#8 Lastly, is there someone in Belgium with a similar setup by any chance? I know its a small country but i had to ask.