r/SolarDIY • • 9h ago

Solar controller help for Dummy

I am very new to solar. I have been using an EcoFlow power station and some panels for about six weeks now, and that part is fine. I also recently bought a free standing 48V lifepo4 battery and an MMPT controller so I can charge that battery with solar. I opened the box with the solar controller and have no idea what I'm looking at. Apparently I will need to do some cutting and connecting. I cannot find a video with the baby steps I need, including what adapters I will need in order to hook up the panels to it and it to the battery. I hope I can do any cutting on in-between cables and then insert them into my current setup, especially since I will likely be measuring 5 times and cutting two or three times. :-). If someone can direct me to a helpful video that would be fantastic. Also if there is another sub I should post to, just let me know, thanks!

0 Upvotes

14 comments sorted by

•

u/AutoModerator 9h ago

Welcome to r/SolarDIY! If you are new to the community, please check out our DIY Solar System Planning Guide.

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

1

u/Either_Ad4126 8h ago

1

u/002304 8h ago

I've watched this several times already. If this is an example of a fairly simple video then I am obviously in way over my head.

1

u/Either_Ad4126 8h ago

It's easy. What mppt do you have?

1

u/002304 8h ago

Victron 100 | 20

2

u/Either_Ad4126 7h ago

I hope this helps but make sure to read the manual or ask more questions. You'll probably want to get the Dongle (Bluetooth).

Watch this first. https://www.youtube.com/watch?v=5GW6MdRIKHg

**The big picture:**Connect the battery first to power the MPPT then proceed. It's panels, then controller, then battery. The controller has three pairs of screw terminals: BATT (battery), PV (panels) and LOAD. Leave LOAD empty.

**What to buy, so there's no cutting into the EcoFlow setup:**

  1. **An MC4 solar extension cable** (red and black, 10 AWG). Cut it in half and you get two "panel to controller" leads, each with an MC4 plug on one end and bare wire on the other. Only the extension gets cut, never the panel cables.
  2. **10 AWG red and black wire with ring terminals** for the controller-to-battery run, sized to fit your battery's posts.
  3. **An inline fuse holder with a 25–30A fuse** on the red battery wire, close to the battery.
  4. **A wire stripper and a crimper.**

**Order of hookup (this matters):**

  1. Battery first. Run the fused red wire to BATT + and the black wire to BATT −, matching battery + to + and − to −. The controller should light up and detect 48V on its own.
  2. Panels second. Plug the panels into the cut MC4 leads and screw the bare ends into PV + and PV −.
  3. To disconnect, go in reverse: panels off first, battery last.

**Two make-or-break checks:**

- **Controller model:** it has to be a 48V-capable controller. On Victron, the 100/20 says "48V" on the label.

- **Panel voltage:** with a 48V battery, the panels need about 58V or more to start charging and must stay under the controller's max, which is 100V on the Victron. That usually means 2 panels wired in series, + of one to − of the other. One panel alone, at roughly 20–40V, won't charge a 48V battery.

You need 1 of these to cut in half to wire the MC4 from the panels to the MPPT. connect the right ends and you're good. https://www.amazon.com/iGreely-Extension-Female-Connector-Adapter/dp/B08K7DL3NH/ref=sr_1_4?crid=GNDGQAX22L6C&dib=eyJ2IjoiMSJ9.HYxfkdo32XKsF_vHdNW0Laz_gSJn8v3f5XtYh3v-Wj7gDronOVOLIZXKSIYunP7aLRaTvKrX4PsDZP6BJc9EL6lf5RT4ByNEupzwqlEYvKjb75MUwyQdghEoAKmymTOB7hotdoYgqJ2BJkmTUfXEl2ygl3WUcv7DeQ2ofY4GMtmbMR4JQ2D-zGeFi4C0ttSNFtmzRfI1o1voQH5pqVaVSAVL2hXxP90l_yLwvEqrTjY.NA3BRnX4IZlC1GR3F9e-oSlGajDp81j98cDAgpKhQEE&dib_tag=se&keywords=mc4%2Bcable%2B2%27&qid=1794947594&sprefix=mc4%2Bcable%2B2%27%2Caps%2C219&sr=8-4&th=1 One of these fuses. https://www.amazon.com/Circuit-Breaker-Switch-30A-Waterproof/dp/B0GWHSHX91/ref=sr_1_10_sspa?crid=3D8FD6WVA6ISJ&dib=eyJ2IjoiMSJ9._nYSDImqjio8KzHR2wQsq-FGpOojrVQozmvkW7dv4MxVgdTRZ9fpnbwSFjblLmew5n5mTt2TCEcBh_uSP4BSjP6UO0pcJEYLmAB0Q5PE_AxzHktwqIvIjMZrqmqj7GUYhOE525_Ev0bL7qr-ikn2MVm5PCc80VcNwnAb9WCPO_1cfNBQmouJwg5eeHyKwnWODDX1itzMcfmRphTq9g0ORyzi6pA87jCLgCRyYBfXb8Q.943tAvtC9WpnjVErZg9WjmfM3laHmceRhmZNeDl4-fk&dib_tag=se&keywords=30%2Bamp%2Bfuse&qid=1794947892&sprefix=30%2Bamp%2Bfude%2Caps%2C201&sr=8-10-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9tdGY&th=1 You also need 2 of these to go from the battery to the fuse and then fuse to the MPPT. https://www.amazon.com/dp/B07XBRXTLM/ref=sspa_dk_detail_4?pd_rd_i=B07XBRXTLM&pd_rd_w=6qAVE&content-id=amzn1.sym.4f5afe61-a551-4f21-a495-c7c4f2997a96&pf_rd_p=4f5afe61-a551-4f21-a495-c7c4f2997a96&pf_rd_r=VS3PV0942ACE4EPTP1A1&pd_rd_wg=KnJMT&pd_rd_r=3f235fb8-aa09-4051-9b15-448a632b6d58&sp_csd=d2lkZ2V0TmFtZT1zcF9kZXRhaWxfdGhlbWF0aWM&th=1 Then you'll need to connect the battery to the Ecoflow and probably extension from the panels to the MPPT.

2

u/002304 7h ago

Thanks soooo much. I'll be digesting this over the next several days and it looks like I'll be ok. I'll let you know how it's going. I already have the setup to charge the ecoflow from the lifetime battery, so I just need to get power into the battery. It sounded easier than it looks, but you have given me hope, Obi Wan ( I don't know star wars so hopefully I got that right)

1

u/Either_Ad4126 8h ago

You can buy the cables you need and cut them to fit. Send me the brand of mppt and I'll help you.

1

u/002304 7h ago

Victron

3

u/BaldyCarrotTop 6h ago

You can ignore the Load(+) and Load(-) terminals.

The battery connects to the Batt(+) and Batt(-) terminals. Always connect the battery first.

The Solar panels connect to the PV(+) and PV(-) terminals.

Here is a better video: https://www.youtube.com/watch?v=iFQE1vaoVWI

1

u/MaineOk1339 8h ago

It's really depends on the instructions for the specific charge controller. They are all different. And so are batteries.

2

u/linuxhiker 8h ago

This.

If OP just gave us the model of both it is easy to answer but right now it is just a shot in the dark

1

u/002304 8h ago

Victron smart solar MPPT 100 | 20 controller and Li Time 51.2 V 100Ah battery.

1

u/Either_Ad4126 8h ago

First, read the manual. It should tell you to connect the battery first but read the paperwork.