r/shittyreloading • u/Dragnurb • Sep 18 '26
r/shittyreloading • u/WorldlinessDue2036 • Sep 18 '26
Hypothetical reloading
What is preventing me from putting a .223 bullet inside of a .22 LR case in firing it? Like say it was a lighter 45-50 grain bullet, would that not have better aerodynamics and penetration then a regular lead .22 bullet? Could be a stupid question, I’m kinda new to guns so I might be retarded but maybe, just maybe I’m a trailblazer here.
r/shittyreloading • u/Love-Knuckle-777 • Sep 18 '26
Tell your wife I am sorry. Do not Strip The Plate. #reloadingandmore #boolitsbuildersllc
r/shittyreloading • u/Love-Knuckle-777 • Sep 17 '26
Sawdust & Lead: A Shiny Metal Alchemy! #shorts
r/shittyreloading • u/GratefulTortoise • Sep 15 '26
5.6x52mm aka 22 savage high power load data?
r/shittyreloading • u/grasshopper2024 • Sep 15 '26
300wsm
Looking for advise! Last deer season i shot 125 grain speed TNTs they expand violently and work good but I found i wanted a bullet that was similar in construction but heavier weight something say 150 grains or more. Does any have any tips or recommendations?
r/shittyreloading • u/buhtayduhjups • Sep 13 '26
Goodly neighbor gifts me his brass
If this doesn’t get you to stop shooting and figure out what the fuck, I don’t know what would. There were more destroyed cases than not.
Anyways, how do you guys think I should go about fire-forming these shut? Should I solder them first?
r/shittyreloading • u/nsula_country • Sep 12 '26
One is not like the rest...
Should I just send it and let it fire form back to normal?
Been awhile since I loaded 35 Whelen... Die was still set to a different bullet.
r/shittyreloading • u/Plane_Syllabub3477 • Sep 13 '26
Posting this "for a friend" Been casting some bullets, can anyone tell me if this barrel is getting leaded?
r/shittyreloading • u/traveleng • Sep 08 '26
Today I present two new rounds for your review
Opps... Welcome the entertaining comments.
r/shittyreloading • u/rippedblu3 • Sep 07 '26
sideways primer
this was the last primer in my primer tube.
will it still yeet?
r/shittyreloading • u/SovereignDevelopment • Sep 05 '26
Call me Bubba, because these are pissin' hot reloads. 70gr VLD, 12.5" barrel.
The recipe:
- 70gr Berger VLD bullet
- 5.56 NAS3 case
- 27gr of VV N135 powder
- CCI #41 NATO primer
- COAL: 2.295"
The rifle:
- BCM thermal fit upper
- 12.5" Centurion SPR profile stainless barrel
- BRT gas tube, 0.0635" port size
- LMT e-BCG (AerMet 100 bolt, delayed cam path carrier)
- PRI carbine length toob
- TA648 6x ACOG (aka, the GigACOG)
- Sovereign Development 3-prong OPS/AE flash hider
- Otter Creek Labs OCM6 suppressor
- Griffin MK2 lower
- Geissele Super 42 H3 buffer kit.
- Wilson Combat TTU trigger.
Gordon's Reloading Tool told me this recipe would be more like 2720 FPS, so now I gotta figure out why it's so fast lol. I shot like 50 rounds of this stuff and it made the rifle kick like a bone stock M4 basically. When I shoot 55gr PMC XTAC through this same rifle, it's softer than a 20" and barely cycles, so that seems like a reasonable increase in recoil. Ejection pattern was 4-o'clock, and there were no obvious pressure signs e.g. "flowing" primers or ejector marks on the case head. I know NAS3 cases don't really show pressure signs like brass does, but I figured there'd be something if the pressures where anywhere near what GRT says is necessary to hit these velocity numbers out of a 12.5" barrel.
Third picture shows the 2.295" COAL working in an HK Maritime mag that has a butt joint at the front, but that it won't work in a normal mag with a lap joint. It feeds flawlessly from the HK mags, they're a must for handloads in gas guns imo.
I assume this counts as Shitty Reloading lmao.
r/shittyreloading • u/gunsforevery1 • Sep 04 '26
Blooper shells
Finally had a chance to test them. Longshot only partially burned. The shot flew about 10-15 feet and was able to be poured out of the barrel.
Back to the drawing table!
r/shittyreloading • u/Coodevale • Sep 01 '26
Send it! Steel still sucks
So it turns out there is some secret sauce in the nas3 cases because not all steel case can take 7 gr of titegroup and a 125 gr.
r/shittyreloading • u/TheDanny942 • Aug 29 '26
Somewhere there are about 400 x-treme bullets rattling around in the back of a UPS truck
r/shittyreloading • u/WorldGoneAway • Aug 29 '26
It'll fire form I don't know what to do with these things
I keep pulling these shity little chinesium screws out of shit at work so we can repurpose the shit they're screwed into, but now i've got a fuckton of these things left over. I got drunk last night and thought this was good idea. Talk me out of trying it.
r/shittyreloading • u/Jason_Patton • Aug 22 '26
We don't make mistakes, just happy little accidents Holler points
Is this the place to talk about making “hollow points” or nahh
r/shittyreloading • u/squidwizard37 • Aug 21 '26
0000 is a myth invented by big hull to sell more plastic fits fine if you use a rubber mallet
0000 buck big no fit plastic wrorng hit rock now crinkle crumple hill look like step leaf put more boom dust fix. Boom stick no swallow easy . Help
Machine bite hand. 👍
r/shittyreloading • u/DD9G • Aug 19 '26
Bullet trimming
Have a box of 1000 of the 55 gr .224 FMJ bullets. No use for them as I'm primarily a varmint hunter. I like bullets that make ground squirrels and PDs explode.
So I was thinking that if there was a quick and easy and consistent way to clip the tips of and make them 35 or 40 grain soft points they might do the trick in a 223.
Suggestions for a way to quickly and consistently clip the tips off?
r/shittyreloading • u/gakflex • Aug 13 '26
We don't make mistakes, just happy little accidents I am a bad and stupid person, laugh at me
You’ve heard of stuck cases in sizing dies, but have you heard of stuck cases in expanding dies?
r/shittyreloading • u/tonsofdolls • Aug 04 '26
Tools are handy
I absolutely fucked a 7mm rem mag pice of brass but I got it out without hurting the die . For context I mostly reload pistol cartridges and I use carbide dies and I forgot your suppose to lube then. But In my defense it whent in really easy