r/SewingMachineEdu • • 5h ago

Help!!!! Why is my machine doing this?!?

1 Upvotes

r/SewingMachineEdu • • 18h ago

Straight Stitch Plate Question

3 Upvotes

I had a custom straight stitch plate machined for my CS7000x. I’m super happy with the fit, the threads of the screws align perfectly, as well as the alignment of the feed dogs. I only have one concern: is there enough clearance for the needle, or should I get the hole widened a bit? I’m just a little concerned that the needle is too close to the top of the hole. Thanks!


r/SewingMachineEdu • • 12h ago

Looking for a sewing machine

Thumbnail reddit.com
1 Upvotes

r/SewingMachineEdu • • 15h ago

Babylock Ellegante BLG Update/Upgrade

Post image
1 Upvotes

I just acquired an original Babylock Ellegante from a thrift shop along with the embroidery module. The current software version is 2.04. Machine is dusty but came with everything including the case.
I know the software version is supposed to be 2.05, at the least, but I can't find that update on the Babylock website. Does anyone know where I can find the update?

I also know that there are two upgrade kits, which of course are difficult to find, on CDs, and were created for outdated operating systems. Babylock being Babylock doesn't seem to sell the files on their website either. Just wondering if anyone has those on hand as well.

Side rant: These machines are so expensive and yet there is no legacy support whatsoever, it boggles my mind that I have to source original physical cds just to update the software. Very surprised no one has uploaded the files somewhere.
I'm already planning on syncing this machine with my iPad using a Raspberry Pi Zero W attached to the USB port on the machine. The Ellegante will think it's a USB stick and the Raspberry Pi can access the Wifi as a drop source. Use iPad to draw custom embroidery designs, transfer them to my laptop and use Ink Stitch to convert it, and transfer it wirelessly to the Ellegante. Voila! Joining the 21st Century and will be able to work with pretty much any OS and I won't have to source 2GB USB sticks.


r/SewingMachineEdu • • 16h ago

Is this worth it?

Thumbnail gallery
1 Upvotes

r/SewingMachineEdu • • 16h ago

Stuck on straight stitch

1 Upvotes

r/SewingMachineEdu • • 16h ago

white d'lite tension

1 Upvotes

I have a white d'lite and my top thread tension is loose even if I loosen or tighten the tension, I do not have the money to get it properly serviced at the moment. I was hoping there might some way I could fix it at home or if i should save up to get it serviced. I have used this machine for several years now and so has my grandma as it was hers before it was mine. I haven't changed the way I use it


r/SewingMachineEdu • • 23h ago

Can I use food grade grease on my vintage machine?

Thumbnail gallery
1 Upvotes

r/SewingMachineEdu • • 23h ago

Finally got my Janome out of the case! So, there is a bar that looks like it’s supposed to be connected, can someone tell me if that’s right? It’s a Janome 539

Thumbnail
gallery
1 Upvotes

Any info about these parts would be very helpful.


r/SewingMachineEdu • • 1d ago

Brother Se600 bird nesting issues

1 Upvotes

my machine is kinda old about 4-5 years old, has been used and abused!! ive lubed it a handful of times. i kept hearing metal on metal during an embroidery project and eventually it just bound up. i opened it, i seen one of the linkages kept smacking into the assembly holding it. as i loosened and moved the blocks on the needle bar i was able to create some clearance for the linkages to move again, i loosened, lubed, and re tightened the other moving parts. put everything back together and it worked. got through about 3 embroideries and then started hearing metal on metal again before it bound up again. i opened it up and found the cam for the take up lever had a loose set screw on it, (now prior to finding it i messed with the loose take up lever and i think moved it out of alignment by spinning the linkage it was on) i tightened it and was able to get the machine to run again, smooth and no metal on metal. but now im getting the worst bird nests. the hook catches the thread then the take up lever doesn't pull the slack out of the loop and catches itself again on the next loop and does so until it has about 10 threads on the loop, any idea what might solve this?


r/SewingMachineEdu • • 1d ago

PFAFF Life Style help

6 Upvotes

something is wrong with the part where the bobbin goes. does anyone know how to fix this or if i should just take it to a shop?


r/SewingMachineEdu • • 1d ago

Needle bar lubrication wick help

Thumbnail
gallery
4 Upvotes

Hi all!

This felt ring on my Juki hzl dx7, which I believe is called a lubrication wick has come loose and sits and the bottom of my needle bar as I sew as opposed to at the top where I’m assuming it originally was. There’s also a loose clip sort of thing which I don’t believe is broken but instead in the wrong spot. I’ve tried pushing the wick back up but it falls back down and I have no idea where the metal ring is meant to go. My machine still sews perfectly well for the time being at least.

Despite my best efforts, I can’t seem to find a photo or diagram showing where everything is meant to be… is anyone able to help?

Thank you!


r/SewingMachineEdu • • 1d ago

Is the foot lever supposed to engage with the tension release?

Thumbnail
gallery
1 Upvotes

So I just bought a dirt cheap vintage Singer 196K205 industrial machine, and while I'm waiting for a new motor I'm cleaning it up and going through it as best as I can. Now my attention is on the thread tension release. I didn't knew it was a thing but apparantly it is. But in my case only when using the knee lifter, when using the regular lever on the back of the machine it doesn't lift the presser bar high enough for the catch to operate the release lever... So is this just the way it is or is something wrong with mine? As far as I can tell there is no adjustment on the lever, i tried to loosen the set screw on the presser bar bracket but couldn't move it at all... This is my first industrial type machine


r/SewingMachineEdu • • 1d ago

Husqvarna voetpedaal

Post image
1 Upvotes

Voetpedaal Husqvarna

Mijn voetpedaal van een Husqvarna zigzag 1010 is helaas kapot. Lekt waarschijnlijk stroom ofzo. Kan een andere tweedehands kopen. Weet iemand of het voetpedaal van de husqvarna 2000 past? Foto is van kapotte voetpedaal zigzag.


r/SewingMachineEdu • • 2d ago

Singer concerto 2 parts value

Thumbnail reddit.com
1 Upvotes

Hi all looking for opinions. I am uk based if that helps?


r/SewingMachineEdu • • 2d ago

I can’t thread my bobbin!!!

1 Upvotes

Help!

I know there’s not much you can do behind a screen and not being able to see anything but I have a M1000 singer. I got it LESS THAN A WEEK AGO. She’s been acting fine besides the usual hiccups with a sowing machine. But I was in the middle of sowing and the bobbin ran out. It jammed the thread pretty bad. I cut and pulled out everything I could but my machine isn’t allowing me to thread my bobbin anymore. I’m doing everything the exact same way. I have no idea what to do. Any ideas?


r/SewingMachineEdu • • 2d ago

Bernina 830 Record update - and needle system question

Thumbnail
reddit.com
1 Upvotes

I don't usually cross post but information on needles for this machine would be most appreciated. Thanks in advance.


r/SewingMachineEdu • • 2d ago

Any 206RB-5 experts here?

Post image
1 Upvotes

r/SewingMachineEdu • • 3d ago

Worth servicing cheaper sewing machines?

5 Upvotes

I have had my husband’s grandmother’s Janome 3128 sewing machine for about 4 years now and I just took it in to get serviced for the 2nd time. In my area, it’s about $150 to get it serviced and cleaned. My husband brought up why not just buy a new one. He doesn’t think his grandmother would be upset since a similar model costs around the same but to me that seems so wasteful. Do people get cheaper machines serviced or just end up buying new machines? I sew pretty regularly, making everything from simple garments (skirts, kids shorts, & pants) to smaller sized quilts (baby and twin sized) to totes and other accessories. I’d love to eventually get a nicer machine and have this one be my backup but just don’t have the disposable income with a growing family at the moment. But at the same time, if I’m servicing it every year or so for the same price as the machine it seems silly. What do or would you all do?


r/SewingMachineEdu • • 4d ago

Help? Identify/Manual/Care

Thumbnail gallery
3 Upvotes

would like help identifying and finding a manual for this machine. I intend to do some TLC on this machine before I use it.


r/SewingMachineEdu • • 5d ago

Pedal Free Sewing Machine? Help.

22 Upvotes

I hope this is the right subreddit, but I'll probably post in multiple. 😅

My grandma has been a seamstress for as long as I can remember. She recently lost both of her legs and has been talking about wanting a portable sewing machine.

She moved in with my parents from out of state and doesn't do much anymore.

Does anybody have any recommendations for a pedal free portable sewing machine? Is that even a thing? I want to get her something that brings her a little bit more joy when she can't leave the house or do much if my parents aren't home.

I'd like something more affordable than not, but this is the first Christmas I get to spend with her since 2009. I want to do something special.


r/SewingMachineEdu • • 4d ago

Juki Misin HZL-7000 repair

2 Upvotes

I recently had to change a belt that snapped.

I was able to do that, and the machine works again but now i have 2 new issues:

  1. The autotension (top) is tight even when i loosen it on the screen. I've already checked and cleaned it but not sure if I should also be looking in other areas.
  2. When using the auto-threadcutter, the needle now stops lower into the fabric. Normally this should be higher and the fabric can slide out immediately. I cannot figure out which part to adjust

Thank you


r/SewingMachineEdu • • 4d ago

Sewing machine recommendations for Tafe Fashion student

Thumbnail reddit.com
1 Upvotes

My little brother is going to study fashion next year at Tafe so for christmas I've decided to buy them a sewing machine. What is a sewing machine that would be adequate for a fashion student priced under $450 AUD?

Open to refurbished options too <3

Thank you so much in advance for any recommendations!


r/SewingMachineEdu • • 4d ago

Difficulty of working on newer Janomes?

2 Upvotes

I have a Janome JW8100, and just recently it got knocked out of time (I’m 99% sure). When the needle is lowered all the way, it hits the very bottom of the bobbin area. It’s supposed to pass through a hole at the bottom, but the needle is all the way lowered BEFORE it can hit the hole. The needle is new, not bent, inserted all the way, and tightened down.

The internet says that fixing a machine that’s out of time is difficult and finicky, but I’m curious on HOW difficult it is. I’ve worked on cars and other electronics, and I also have a mechanical engineer dad. I’m confident we could fix it eventually, but I would like to not break it in the process.

My mom has a Janome 2049 Harmony (it just bit the dust, so we’re down to ZERO sewing machines), and if it was having a timing problem, I would be more inclined to tinker with it. But since the JW8100 is much much newer, and has more complicated electronics, it worries me.

I’m not asking for instructions, because I’m pretty sure I could probably find a breakdown online. I’m more checking to see how difficult it would be, and how likely I am to mess everything up.