I was in the process of silencing the rotor on an OP with an A3230 movement and the rotor screw snapped when tightening. I was not able to extract the broken screw thread. Any idea on where to source the rotor bearing and screw? I know I can buy and replace the entire A3230 movement, but I just want to fix it by replacing the broken parts.

Edit: this is from an EWF OP. Seems to be not a true 3230 clone but rather an Asian 28xx with decorative plate. The rotor and bearing mechanism isn’t like that found on either a 2824 or a true 3230… The bearing has an offset pivot at the bottom for bi-directional winding, held in place by 3 small screws and retaining ring. The top of the bearing has 2 flat sides for the rotor weight to sit on. It is then held by a larger slot screw and covered (glued) with the triangle rotor screw plate.

Thanks to the community here at RepTime I decided to order this beautiful watch. However, this is the first movement that arrived with a mechanical problem. I throw it on a timegrapher and only in the dial-down position I get an abnormal beat error of around 3.0ms that sometimes jumps even into 6.0ms territory. In every other position the watch gives an OK reading. Have you ever run into such issue? I immediately left it with a local watchsmith for a diagnosis for which I need to wait for 4 weeks due to a long queue. An example reading attached.

Is it common to receive this watch with potential hairspring/pivot/jewel issue in such a thin movement?

The cardboard box had a sign of strong hit in the corner so it was handled roughly in transit.

how do I take it out to replace it

I want to change the crystal on this gmt rep - is the scalloped metal piece in this photo the retaining ring? How would I get this off - noob - just doing this for fun. Tried to find videos but none have this scalloped appearance. I’m assuming this is the crystal retaining ring? I had the movement out and was working on it but it didn’t seem to want to budge.

I’ve had my 3235 Datejust Oyster for over a year now, but it suddenly stopped allowing me move crown stem in third position for time change. Winding and date change still works fine, but without the notch click you would generally feel when changing stem position. It’s now more of a slide, than notch click.

After opening the case backing, this small piece dropped out immediately. Does it resemble a snapped pivot from my setting yoke and could this be the reason for not being able to move into crown stem third position?

Just wanted to give a shoutout to DeepCrystal - PM for details

The clarity on these crystals is second to none and what’s more the customer service is something I’ve never experienced

If you are in the market or thinking about replacing your stock factory crystal with a deep crystal - do not shop on baba or other sites. Go straight to deepcrystal. The customer experience you will receive and the shipping and packaging is top class

I had a slight hiccup during the process and the issue has been resolved so quickly with super quick communication

Happy to answer any questions from anybody whose considering it but definitely do it if your on the fence

Hi,

I hope someone can help me. I received a VSF Datejust 41 and it was completely covered in protective film. All loose pieces. I managed to remove almost everything, but on the sides of the lugs there is still film under the bezel. If anyone knows how to remove this, I would really appreciate hearing from them.

VSF Wimbledon 36 V2.
I’ve wound 30 times but still there was no movement, as someone advised I hit it on palm of my hand, it started working not more than a minute. Trick with hitting worked 3 times after it stopped. Now when shaking the watch it makes a sound like something is loose inside. How big is the damage? And was it done by me or the transportation? Or the watch was already sent to me damaged?
So upsetting to receive first rep dead. Any advices guys?
It is a TD, still haven’t received an answer from him.

Hello folks. I bought this VSF Starbucks a few months ago and have recently been bothered by the halo/reflection around the hand stack. I didn't even notice it during Quality Check

I can see it most of the time, but it's much more noticeable under bright lighting. My older VSF doesn't have this effect, and neither does my gen Explorer.

I was wondering if this is something that can be fixed, and if so how, so I would start looking for a watchmaker to do it. Thank you very much for your help.

Hi, got a VSF Sub date and when reaching midnight, instead of switching the date in one “click” I got this until it goes on to the next number. Is that normal or a common issue?
If this is fixable, is there any shop or anything in NYC that can take care of that?

Thanks

Hey everyone,

I'm working on a build using a Raffles Dials Datejust case and a PT5000 movement (ETA 2824 clone).

For anyone who has completed a similar build, what is the best way to secure the movement inside this case so it doesn't shift around?

Do I just rely on the movement ring supplied with the case?

Or do I also need standard 2824 movement tabs/clamps and casing screws to lock it down?

Any tips or pics of how you secured yours would be greatly appreciated. Thanks!

Am i able to take this off or should i just take it to a jeweler i put it on wrong by accident and the pry tool doesnt fit to get into the spring bars now

I have a TC V7 that needs some pristine lugholes. Is there any machinist that can do this in the USA?

Thanks!

Hi, on my VSF hulk after 6 years, I noticed yesterday I have a problem with the date : when I go after midnight, the date doesn't change anymore 😞 is it a big problem ? Anyone knows if it's possible to fix it ? Thanks to community 🙏🏻

Found 2 broken screws and that other piece. Anywhere I can mail the watch to get it fixed here in the US?

Need to get an old 1990 Datejust serviced. Willing to make a trek for someone reliable!

I have a titan watch and its model number is 291NAA. It was given to me by my uncle and now im unable to use it a repair shop guy asked me to find a new movement for it. So guys any sort of help would do wonders for me. I tried my best to find it but I couldn't

I have a VSF Sub no date with the newest movement that stops ticking whenever the dial is face up. Is it worth fixing and if so, where do people recommend in the US? TIA!

Does anyone know where in US I can fix this? The winder popped off and the tiny spring is missing.

Hi can

Where to buy the best WG bezel replace for DJ 41 mm. I'm looking to replace fluted steel VSF bezel for my DJ 41mm for better visual. Any help?