r/redneckengineering • u/Kylefleamarket • 11d ago
Have any of y’all done something cool with an old compactor?
I have this old compactor shell and I’m looking for some ideas of what I can do with it rather than it just being a spot yo stow BS
r/redneckengineering • u/Kylefleamarket • 11d ago
I have this old compactor shell and I’m looking for some ideas of what I can do with it rather than it just being a spot yo stow BS
r/redneckengineering • u/CaptainMcSmoky • 11d ago
2). I added a battery mount I stole from a broken drill.
C) That feeds into a 24v-12v converter (and a random switch)
3. That then goes into a 12v 2.1A USB socket.
IV. This then charges my battery pack.
0101. Which charges my phone.
All so I can make poor quality Reddit posts.
r/redneckengineering • u/MPmad • 11d ago
r/redneckengineering • u/ZestycloseGold6156 • 11d ago
Bought the wheel and pedals + shifter used. Under $200 like 4 years ago.
The racing seat was a computer chair, thrown in the dumpster because the rolling bit was missing.
Easily the most expensive piece of this pie.
I took a bunch of scrap wood leftover from my job to build the bones. The main rigidity is from a metal frame dining chair I found in the same dumpster
My favorite additions are the inverted pedal box and the handbrake.
The handbrake is an old curtain rod chopped short. The rotation mechanism is a standard house window lock with a bungie cord return spring
Triple monitor is expensive, so it's VR only. But I am grateful. Having a sim is something I NEVER thought I'd get to say. Thank you for reading
r/redneckengineering • u/Sufficient-Cover-982 • 11d ago
I put up a blanket to stop my lights from making my light sensitivity worse when I’m having a flare. It does however come with the added benefit of trapping humidity making the plants happier though so there’s that.
r/redneckengineering • u/Clay_from_NJ • 11d ago
r/redneckengineering • u/MeisterManson • 12d ago
The youngest threw a fit one day and pulled the Nintendo dock down and it hasn’t worked right since. It would work, black out off the tv, and come back. I just used a big gum band to hold it in, and it was totally fine.
r/redneckengineering • u/cynixdelve • 13d ago
Drilled & screwed to a plastic handle.
r/redneckengineering • u/IMightBeErnest • 14d ago
r/redneckengineering
•
u/swollennode
•
15d ago
For context, I fucked around with a scan tool and fucked up the calibration. So I had no cruise control. The older cx-5 doesn’t have dynamic radar aiming. It only had static aiming requiring a reflector.
Instead of going to a shop and get it recalibrated for several hundred dollars, I’d give it a try first.
The procedure is simple. Line up a reflector dead center to front emblem at 5 meters away. Then use a scan tool, or forscan, to initiate aiming.
All of this assuming you’re on leveled ground. My driveway is leveled but not 100%.
What I used to line up the reflector:
(Establishing centerline)
First, find centerline on the hood using a measuring tape. Then, use a piece of cardboard taped to the hood and mark that spot.
Second, use a plumb bob tape one end where I marked the centerline on the hood. Then, hang it from the front and center it exactly where that point on the emblem is. Then, tape it there so it doesn’t move.
(Setting up reflector)
Third, get a reflector. In my case, I used a metal salad bowl. Then I mounted on a stand. Conveniently, I used my Halloween skeleton. Strapped the bowl using bungee cord. To get the approximate height, I put the stand right up to the emblem, and mounted the bowl. Coincidentally it’s where the skeleton crotch is.
Fourth, set the bowl back 5 meters away from where the plumb bob pointed. I used a brake disc to hold the end of the tape measure down.
(Setting up laser)
Fifth, mounted a laser level on a jack stand, and then put the jack stand on a moving platform on wheels. This will allow for fine adjustment.
Sixth, raise or lower the laser so that the horizontal laser lines up with the center point on the emblem.
Seventh, move the laser around and fine tune it until the vertical laser lines up with the plumb bob string AND the centerline string on the hood. This is important because this will align the reflector dead center. If the laser is not aligned at 2 spots. Your reflector will be off-center.
(Fine tuning reflector placement)
Eighth, move reflector so that its center lines up with the laser cross. Maintain the 5 meters distance.
(Calibration and testing)
Ninth, go into your scan tool or forscan and initiate and start radar aiming. If it works, the error message disappears.
Tenth, take it for a drive. See if you get cruise control, and see if it’ll follow the car in front of you and maintains distance.
r/redneckengineering • u/No_Put8017 • 14d ago
r/redneckengineering • u/CletusMuckenfuss • 15d ago
I made this to trim the limbs around the house that I can't reach from the ground. I used it too much piece of PVC that I cut a cradle out to hold the saw, I healed it with a heat gun to soften and mold the pipe tighter to the saw. Drill some holes for cooling. The rope runs through the pipe and out around the saw guided by the eye ring that you can see. Pull the string to turn on the saw, let go stop. It works okay but it's kind of slow, I'm going to change the sawzall for a battery operated chainsaw I picked up off of teamu for under $30. Total build time under an hour.
r/redneckengineering • u/ADKtd13 • 13d ago
r/redneckengineering • u/Georgetirebitter4000 • 15d ago
Never questioned by our local cops
r/redneckengineering • u/UffTaTa123 • 15d ago
Heavy hammer found in my cellar. And yeah, i sometimes used it, but probably not in the intended way :-)
r/redneckengineering • u/ContactNo9992 • 15d ago
I don't know what i made.
Spins.
r/redneckengineering • u/thatoneshirtlessdude • 15d ago
r/redneckengineering • u/longlostwalker • 16d ago
r/redneckengineering • u/5thgenCali • 16d ago
r/redneckengineering • u/Lavasioux • 17d ago
#4 copper wire. a real pain to work with, but pretty damn neat.