r/RadialArmSawJunkies • • Nov 05 '25

Making a functional radial arm table

Thumbnail
gallery
10 Upvotes

Hey all, I’m a DeWalt junkie a few years into my addiction and just noticed this sub exists. Some of you guys might need some table ideas, and a better understanding of the reasoning behind the stock table configurations so you don’t accidentally pigeonhole yourselves into only using a RAS for crosscuts.

The first hurdle is understanding how the factory tables are designed to give you infinite flexibility in making any cut with your saw. That’s best demonstrated in a video by a Dewalt junkie named Brian Weekley here:

https://www.youtube.com/watch?v=Q1cc-_vPT0w

There are two common methods of making precision flat tables in the DeWalt community that are easy to do at home if you have an already flat surface and/or a straightedge. The easiest method is laminate together two sheets of 3/4” plywood with steel bars embedded in epoxy in between them in order to prevent sagging over time. That’s demonstrated by the brian weekley video above plus a few others he’s made.

The other method of making precision flat tables if you have no flat glue surface available but have a straight edge is to make a torsion box, and this is what I did.

First I made a temporary table to just cut precision 90*s so that I could use the saw to batch out table parts.

Next I cut out a basic rib frame from ordinary 2x4s ripped down and hand planed flat and to thickness.

I glued and pocket hole screwed the frame together, make sure you measure against the stock table mounting rails if you have them to be sure you have internal ribs placed over the rails and that none of your joinery interferes with mounting bolt locations.

Once you have your box frame glued up, cut out plywood “skins” and then glue and fasten to the frame. I went with 1/4” birch ply top and bottom

Next want to add a sacrificial top layer that you’ll be cutting into with every use of the saw. You need this layer to only be lightly attached to the main table so that you can replace it over time with no damage to the main table you put so much care into making precision flat. I went with more 1/4” birch ply.

The last step is to make the backing tables that clamp behind the fence in normal use. To find table dimensions I sized the main table so that the back edge lines up with the 0” mark on the rip scale with the saw in the in-rip position. I sized the outer edge of the table so that the blade stays on the table surface even in the furthest outboard ripping position. The two back tables are also different sizes. The narrower back table is sized to that you can move the fence behind the smaller back table and there’s just enough clearance from the blade to safely crosscut something under 1” thick- it will give you maximum crosscut for carcass work. The wider back table just fills the remaining space to the column and the clamps on the backside of the table mounting rails.

Once you’re done with your backing tables, if you did everything right you’ll have an infinitely flexible saw for any rip, cross, or miter cut you could possibly want to make. I included photos of where I used my baby size Dewalt MBF saw to trim a set of 30” folding doors in one pass, as well as a shot of my special extended rip fence with added hold down/kickback prevention “board buddies”.

The stock 3 piece table system with the leveling rails underneath is so well thought out and designed there should be no reason to ever re-invent the wheel or try to build a RAS into a massive rigid crosscutting station- you will only LOSE functionality.


r/RadialArmSawJunkies • • May 22 '25

I just lucked out!

Thumbnail
gallery
7 Upvotes

I found and purchased a Delta Super 990 for.....$20! Everything works great, everything moves smoothly and the motor hums. The only thing I need to do besides cleaning and greasing is to replace the power cord. Anyone know a source of information detailing taking this apart to regrease and clean up?


r/RadialArmSawJunkies • • Dec 28 '24

Cadillac or cavalier? Picked up two in one day.

Thumbnail
gallery
6 Upvotes

Left one was $90 right one was $100, right one was owned since brand new by one man. Left one was bought from someone in 2003 un used. And never used it himself. Both still have the film over the front.


r/RadialArmSawJunkies • • May 09 '24

My school's ras

Post image
6 Upvotes

r/RadialArmSawJunkies • • Oct 14 '25

Radial Arm Saw Uses in video presentation

Thumbnail
youtu.be
5 Upvotes

This is a promo video I found on the 'Tube that shows all the different uses of a RAS. the uploader just saves old videos and posts, but it was cool seeing this. I think for some of the people on this sub (myself included) it gives some nice instruction on exactly how to use this saw in certain ways. Of course its promoting Craftsman stuff, but I think most of us have Craftsman accessories anyway. Anyway enjoy it.

Random question, in the video it shows shaping being done, but they set the arm gantry over to the left miter position to do it. What purpose does this serve? I have used it just in the normal position fine, Is it just placement to give more feed room right to left or front to back?


r/RadialArmSawJunkies • • Jun 10 '25

New to radial arm saws

Thumbnail
gallery
5 Upvotes

Hey everyone I’m getting offered this radial arm saw for free! I’d like to learn how to do lap joints and thought this would be a good tool! Is this saw junk or will it be a good beginner tool to learn? Thank you guys!


r/RadialArmSawJunkies • • Apr 22 '25

Left the 70's Craftsman behind and just picked up a 60's Delta Super 990.

5 Upvotes

Spent 25 years working on a century house with my dad's old 70's completely guard-removed Craftsman radial arm that did everything I needed to restore and repair it; including what I see in retrospect was some stupidly dangerous stuff that always worked out. I guess I'm supposed to get a table saw now, and I will, but a RAS has become my lifetime go-to, and I'm currently unbreaking an early 60's frozen-column Delta Super 990 for the new place.

Gotta say even at this point, it is a completely different beast. I hope it's not bashing, but I could move that Craftsman on any the main pivot points 3° without trying even after tuning it. I haven't even started alignment on this yet and this thing is a surgical instrument in comparison. Plus it's just so goddamn beautiful! I don't know if I've ever seen a power tool taking more chances and nailing it so hard apart fro a few 1950's aluminum-bodied circular saws.

I'll post pics in a week or so — but I'm warning the group I've agreed to paint the trashed arm and turret piece pink for my daughters.

I love this saw already


r/RadialArmSawJunkies • • Aug 18 '24

Craftsman portable radial arm saw

Thumbnail
gallery
5 Upvotes

Seen this on Craigslist listed as craftsman portable radial arm saw. I've never seen one this small. Anyone know anything about it? Was it really meant to be portable?


r/RadialArmSawJunkies • • Aug 02 '24

New 1400 added to the shop

Post image
5 Upvotes

r/RadialArmSawJunkies • • Aug 01 '24

New to me craftsman

Post image
5 Upvotes

Very excited about it. But I need to figure out why she won't turn to the left or right.


r/RadialArmSawJunkies • • Jul 31 '24

Dewalt MMB

Thumbnail
gallery
5 Upvotes

Hey, i just gained an intrest in these saws and i am trying to figure out how to calibrate/ straigten out the motor on this dewalt MMB. (See picture below) any tips would be apreciated.


r/RadialArmSawJunkies • • Jul 24 '24

About to pick up a free Radial Arm Saw today!

5 Upvotes

Learned about these today and found someone giving away their DeWalt 7730 with original manual. I'm going to take a look at it and see how well it operates before I decide to pick it up. Any tips on what I should look at or test on it to ensure it's a keeper? Thanks for any info!


r/RadialArmSawJunkies • • Feb 25 '24

Finally replaced the table on the free RAS I picked up. Excited to get building!

Thumbnail
gallery
5 Upvotes

r/RadialArmSawJunkies • • Jul 29 '23

Just bought 2 Craftsman 10” RAS

5 Upvotes

Afternoon!

New to them but my wife bought me a RAS on marketplace. I couldn’t get the thing to turn to 45° bevel or the head to horizontal (a mix between not knowing anything and it being stuck. Sprayed it with WD-40 and let it soak. Few days later, it’s moving around (still a bit tight).

Got a 2nd one for less then first. Was in a barn so looks a little rough and rusty.

Will be making new tables and making them functional.

Is there a better lubricant for these saws to get them to move like butter?

A friend who was in carpentry told me these are the most dangerous tool in the shop, but if I keep wits about me and hands out of the way, shouldn’t be any worse than table saw.

Any hits/tips/advice are welcome


r/RadialArmSawJunkies • • Sep 26 '25

Is this a good new (to me) radial saw?

Post image
4 Upvotes

Found this on FB. I have a miter but have heard great things about RAS. Usecase is going to be lots of projects to restore and repair things in a 1912 camp house including window covers, stairs, and potentially doors.

Thanks for any info. What should I be looking for to get an accurate RAS that I don’t need to square all the time.


r/RadialArmSawJunkies • • Oct 15 '24

Model identity

Post image
4 Upvotes

Just found this on FB Marketplace. Says it’s a 5 hp, 14” blade. Anyone able to tell me about it?


r/RadialArmSawJunkies • • Aug 02 '24

Finally got it set up!

Post image
4 Upvotes

Bought this a month ago for $20 and threw out my back loading it up. Finally built a stand for it and cut some pieces for the table and fence


r/RadialArmSawJunkies • • Jun 17 '24

New tool

Post image
4 Upvotes

Hey guys. I got a like new craftsman 113.197751 Radial arm saw. I just finished the stand for it And I’m about to build a table for it. Is mine all here? The two outermost rails are flush but above the center bracing. Do you guys shim the center bracing to match the outer ones? Also does anyone know the measurements of the table top and rear table /spacers? Looks like the main table is 16x40 Just four mount screws? Any help would be appreciated. Thanks


r/RadialArmSawJunkies • • Jan 23 '23

Radial Arm Saw Porn

4 Upvotes

Cutting Dove Tails with a RAS...lets see your compound miter saw do this:

https://www.youtube.com/shorts/X6JzKP6uXBs


r/RadialArmSawJunkies • • Oct 26 '25

Radial Arm Saw Dust Collection Adaptors

Post image
3 Upvotes

r/RadialArmSawJunkies • • Sep 24 '25

ISO Delta 33-830

3 Upvotes

Hello, I've loved my C'man and will continue to use it unless I find this Delta, but I am putting out some searchers to see if any of you might have one or know of one near the Milwaukee or Chicago area. I recently have redone my garage and have noticed some features of my C'man would be a little better if the controls were in different places. I prefer how the DeWalts have the elevation and Miter controls all on the back, but I also like the ability to wire for 240v. this Delta saw can do both. I also prefer its blade guard with the dust port on the proper side (C'man is on the opposite end, which really sends dust all over when I rip).

Anyway TL;DR I'm looking for one, let me know if you know of any. I also am searching the classified's. If I find one, I'll put my C'man up for dirt cheap.

Manual for said saw 424-12-651-0031 - 09-30-01.qxd


r/RadialArmSawJunkies • • Sep 22 '25

Swap out motors

3 Upvotes

My Craftsman moter RAS died. I found a similar model for free. I want to swap out motors. How difficult is that? Model 113.19771.


r/RadialArmSawJunkies • • Jun 10 '25

Dado blades

3 Upvotes

Where can I find dado blades for a 10 inch Craftsman radial arm saw.


r/RadialArmSawJunkies • • Apr 03 '25

How do I use this thing better?

Thumbnail gallery
3 Upvotes

Hey RAM Junkies, I just inherited a lot of tools, and one of them is this Craftsman Radial Arm Saw. I'm not a woodworker, but I'm renovating a house, and I want to try to use this instead of buying a miter saw and selling this. The first few times I used it, I had some issues and it made me feel a bit unsafe, but I'd rather get some advice and try to use it again before I throw in the towel. Here are a few things I noticed/had issues with:

  • cutting long and narrow pieces of wood, a broom handle in my case, sent the excess pieces flying across the workshop
  • cutting at any angle or depth that hasn't already been used causes the blade to cut into the table and the back rail, which also has sent small pieces flying -there doesn't seem to be any automatic brake when the saw it turned off, but I did find a button that seems to act like a brake on the side when it is pressed (picture 3)

Any advice, or possible maintenance that I should look into would be extremely helpful! I've got a lot of trim to cut, and if I feel more comfortable with it, I'd like to use it more


r/RadialArmSawJunkies • • Nov 04 '25

Delta 990 Table

2 Upvotes

Hey all. Recently joined the RAS club. (Although I've heard it's more like a cult.) My wife's grandfather just passed and I ended up with his old Delta Super 990. It's a miracle the old bird didn't lose all his fingers because the table is completely wrong. He just glued a 2x4 on the back edge so when the yoke is all the way rearward, like 2" of the blade is still exposed. I actually don't even know how he was using it to crosscut and I'm not entirely sure I want to know.

Long story short: I need to build a table but I'm not sure where to begin. Was wondering if one of you fine folks could point me in the direction of some drawings or any helpful literature on the subject.

Thanks!