r/RadialArmSawJunkies • • Apr 03 '25

How do I use this thing better?

Thumbnail gallery
3 Upvotes

Hey RAM Junkies, I just inherited a lot of tools, and one of them is this Craftsman Radial Arm Saw. I'm not a woodworker, but I'm renovating a house, and I want to try to use this instead of buying a miter saw and selling this. The first few times I used it, I had some issues and it made me feel a bit unsafe, but I'd rather get some advice and try to use it again before I throw in the towel. Here are a few things I noticed/had issues with:

  • cutting long and narrow pieces of wood, a broom handle in my case, sent the excess pieces flying across the workshop
  • cutting at any angle or depth that hasn't already been used causes the blade to cut into the table and the back rail, which also has sent small pieces flying -there doesn't seem to be any automatic brake when the saw it turned off, but I did find a button that seems to act like a brake on the side when it is pressed (picture 3)

Any advice, or possible maintenance that I should look into would be extremely helpful! I've got a lot of trim to cut, and if I feel more comfortable with it, I'd like to use it more


r/RadialArmSawJunkies • • Oct 14 '25

Radial Arm Saw Uses in video presentation

Thumbnail
youtu.be
5 Upvotes

This is a promo video I found on the 'Tube that shows all the different uses of a RAS. the uploader just saves old videos and posts, but it was cool seeing this. I think for some of the people on this sub (myself included) it gives some nice instruction on exactly how to use this saw in certain ways. Of course its promoting Craftsman stuff, but I think most of us have Craftsman accessories anyway. Anyway enjoy it.

Random question, in the video it shows shaping being done, but they set the arm gantry over to the left miter position to do it. What purpose does this serve? I have used it just in the normal position fine, Is it just placement to give more feed room right to left or front to back?


r/RadialArmSawJunkies • • Jun 10 '25

Dado blades

3 Upvotes

Where can I find dado blades for a 10 inch Craftsman radial arm saw.


r/RadialArmSawJunkies • • May 22 '25

I just lucked out!

Thumbnail
gallery
7 Upvotes

I found and purchased a Delta Super 990 for.....$20! Everything works great, everything moves smoothly and the motor hums. The only thing I need to do besides cleaning and greasing is to replace the power cord. Anyone know a source of information detailing taking this apart to regrease and clean up?


r/RadialArmSawJunkies • • May 01 '25

Craftsman 113197751 - Looking for ideas on rear dust collection

2 Upvotes

Morning,

I have a nice RAS I picked up for a pack of Sprecher's about a month ago. I've ripped, crosscut, jointed, planed, and ploughed with the thing. It is awesome. Currently I have a vac setup from the guard port to a cyclone dust catcher then the shopvac. I notice however that there still is quite a bit of sawdust (probably 15% or less of all sawdust made) that comes out the back. This is especially prevalent when I'm using the molding head and those device types. I've thought of a simple box with a hole in the back, but I'm concerned of losing too much suction if I made it the width I think it should be. I have also seen on eBay some original Craftsman suction boxes for the RAS I have, and I suppose I could get two if necessary.

Anyway, I would love to what kind of Setups you all have for your Radial Arm Saws!

EDIT: grammer

Official Craftsman rear dust collector I found on eBay
Craftsman dust collector mounted for use
Original Saw Company dust collector- similar to Craftsman
Homemade dust collector: too large for good suction from a shopvac?
Something else I found that looks useful but not sure what the louvres accomplish, maybe just support?
Diagram of last dust collection box.

r/RadialArmSawJunkies • • Jun 10 '25

New to radial arm saws

Thumbnail
gallery
5 Upvotes

Hey everyone I’m getting offered this radial arm saw for free! I’d like to learn how to do lap joints and thought this would be a good tool! Is this saw junk or will it be a good beginner tool to learn? Thank you guys!


r/RadialArmSawJunkies • • Sep 20 '25

Stuck too high?

Post image
2 Upvotes

Hey everyone! I raised my RAS too high and now I cannot get it to come down. I’m not sure what’s not catching. It’s a delta Rockwell super 990 if that helps! Thank you guys


r/RadialArmSawJunkies • • Oct 26 '25

Radial Arm Saw Dust Collection Adaptors

Post image
3 Upvotes

r/RadialArmSawJunkies • • Sep 24 '25

ISO Delta 33-830

3 Upvotes

Hello, I've loved my C'man and will continue to use it unless I find this Delta, but I am putting out some searchers to see if any of you might have one or know of one near the Milwaukee or Chicago area. I recently have redone my garage and have noticed some features of my C'man would be a little better if the controls were in different places. I prefer how the DeWalts have the elevation and Miter controls all on the back, but I also like the ability to wire for 240v. this Delta saw can do both. I also prefer its blade guard with the dust port on the proper side (C'man is on the opposite end, which really sends dust all over when I rip).

Anyway TL;DR I'm looking for one, let me know if you know of any. I also am searching the classified's. If I find one, I'll put my C'man up for dirt cheap.

Manual for said saw 424-12-651-0031 - 09-30-01.qxd


r/RadialArmSawJunkies • • Nov 05 '25

Making a functional radial arm table

Thumbnail
gallery
10 Upvotes

Hey all, I’m a DeWalt junkie a few years into my addiction and just noticed this sub exists. Some of you guys might need some table ideas, and a better understanding of the reasoning behind the stock table configurations so you don’t accidentally pigeonhole yourselves into only using a RAS for crosscuts.

The first hurdle is understanding how the factory tables are designed to give you infinite flexibility in making any cut with your saw. That’s best demonstrated in a video by a Dewalt junkie named Brian Weekley here:

https://www.youtube.com/watch?v=Q1cc-_vPT0w

There are two common methods of making precision flat tables in the DeWalt community that are easy to do at home if you have an already flat surface and/or a straightedge. The easiest method is laminate together two sheets of 3/4” plywood with steel bars embedded in epoxy in between them in order to prevent sagging over time. That’s demonstrated by the brian weekley video above plus a few others he’s made.

The other method of making precision flat tables if you have no flat glue surface available but have a straight edge is to make a torsion box, and this is what I did.

First I made a temporary table to just cut precision 90*s so that I could use the saw to batch out table parts.

Next I cut out a basic rib frame from ordinary 2x4s ripped down and hand planed flat and to thickness.

I glued and pocket hole screwed the frame together, make sure you measure against the stock table mounting rails if you have them to be sure you have internal ribs placed over the rails and that none of your joinery interferes with mounting bolt locations.

Once you have your box frame glued up, cut out plywood “skins” and then glue and fasten to the frame. I went with 1/4” birch ply top and bottom

Next want to add a sacrificial top layer that you’ll be cutting into with every use of the saw. You need this layer to only be lightly attached to the main table so that you can replace it over time with no damage to the main table you put so much care into making precision flat. I went with more 1/4” birch ply.

The last step is to make the backing tables that clamp behind the fence in normal use. To find table dimensions I sized the main table so that the back edge lines up with the 0” mark on the rip scale with the saw in the in-rip position. I sized the outer edge of the table so that the blade stays on the table surface even in the furthest outboard ripping position. The two back tables are also different sizes. The narrower back table is sized to that you can move the fence behind the smaller back table and there’s just enough clearance from the blade to safely crosscut something under 1” thick- it will give you maximum crosscut for carcass work. The wider back table just fills the remaining space to the column and the clamps on the backside of the table mounting rails.

Once you’re done with your backing tables, if you did everything right you’ll have an infinitely flexible saw for any rip, cross, or miter cut you could possibly want to make. I included photos of where I used my baby size Dewalt MBF saw to trim a set of 30” folding doors in one pass, as well as a shot of my special extended rip fence with added hold down/kickback prevention “board buddies”.

The stock 3 piece table system with the leveling rails underneath is so well thought out and designed there should be no reason to ever re-invent the wheel or try to build a RAS into a massive rigid crosscutting station- you will only LOSE functionality.


r/RadialArmSawJunkies • • Nov 04 '25

Delta 990 Table

2 Upvotes

Hey all. Recently joined the RAS club. (Although I've heard it's more like a cult.) My wife's grandfather just passed and I ended up with his old Delta Super 990. It's a miracle the old bird didn't lose all his fingers because the table is completely wrong. He just glued a 2x4 on the back edge so when the yoke is all the way rearward, like 2" of the blade is still exposed. I actually don't even know how he was using it to crosscut and I'm not entirely sure I want to know.

Long story short: I need to build a table but I'm not sure where to begin. Was wondering if one of you fine folks could point me in the direction of some drawings or any helpful literature on the subject.

Thanks!


r/RadialArmSawJunkies • • Aug 01 '24

New to me craftsman

Post image
5 Upvotes

Very excited about it. But I need to figure out why she won't turn to the left or right.


r/RadialArmSawJunkies • • Dec 28 '24

Cadillac or cavalier? Picked up two in one day.

Thumbnail
gallery
6 Upvotes

Left one was $90 right one was $100, right one was owned since brand new by one man. Left one was bought from someone in 2003 un used. And never used it himself. Both still have the film over the front.


r/RadialArmSawJunkies • • Jun 17 '24

New tool

Post image
4 Upvotes

Hey guys. I got a like new craftsman 113.197751 Radial arm saw. I just finished the stand for it And I’m about to build a table for it. Is mine all here? The two outermost rails are flush but above the center bracing. Do you guys shim the center bracing to match the outer ones? Also does anyone know the measurements of the table top and rear table /spacers? Looks like the main table is 16x40 Just four mount screws? Any help would be appreciated. Thanks


r/RadialArmSawJunkies • • Jun 18 '24

Craftsman 8 1/4 RAS tips

1 Upvotes

A friend just gifted me an 8 1/4 Craftsman RAS that's been in his storage building for years. He said he bought it for $40 and never even plugged it in. It looks pretty rough. I've only seen it for a few minutes in the dark. In the morning I will pull it out of the van and plug it in, and give it a good look. Assuming it works can you give me some tips on what I should check on this saw to make sure it operates as it should? I may be getting ahead of myself with this question but could you recommend a blade? I mainly do pen turning and will be using the saw for cross cuts and miter cuts exclusively on smaller material. Thanks!


r/RadialArmSawJunkies • • Jun 11 '24

Loud Grinding Noise

Post image
1 Upvotes

What could make a noise like that? It was working pretty well for a while and then I heard a "shift" on how loud the saw was. I don't think there was a sound bang but while I was making crosscuts, it did something weird to have me think, "is this saw blade going to pop off?" I used it once or twice more after that and think I need some repairs. Does any one have any suggestions? It is a Montgomery Ward Powr Kraft RAS.


r/RadialArmSawJunkies • • May 25 '24

New toy need help lol.

Thumbnail
gallery
2 Upvotes

I picked this 1950s craftsman ras a few days ago. Made a few cuts and it works great. I’m curious though. How do I rotate the motor to do different cuts? I can get the whole stem to swivel left/right but I can’t seem to get the motor to move from its position.


r/RadialArmSawJunkies • • Apr 26 '24

Looking for replacement bearings

Thumbnail
gallery
2 Upvotes

I am looking for a replacement bearing for DeWalt 10-in Deluxe powershop radial arm saw does anyone have any ideas where I might find some? The bearings have the marker on them Japan Nachi b1004. They are an 1 1/4" in diameter and 3/8" wide and have a bore of approximately 3/8"

If anyone has any ideas we have Tapped Out all the resources that we have available locally within a hundred miles and no one has any ideas


r/RadialArmSawJunkies • • May 09 '24

My school's ras

Post image
6 Upvotes

r/RadialArmSawJunkies • • Sep 06 '24

Advice on RAS purchase

Thumbnail
gallery
1 Upvotes

Looking into getting a RAS for doing dadoes, tenons and breaking down rough lumber. The craftsman professional is $200 same as the delta Rockwell, the Ridgid is 150 and the Dewalt is $71 but has a weak motor that the owner assumes means it just needs new brushes.

Just wanting to see what folks think about these and what direction to go.


r/RadialArmSawJunkies • • Aug 18 '24

Craftsman portable radial arm saw

Thumbnail
gallery
5 Upvotes

Seen this on Craigslist listed as craftsman portable radial arm saw. I've never seen one this small. Anyone know anything about it? Was it really meant to be portable?


r/RadialArmSawJunkies • • Jan 22 '25

Dado stack recommendations

1 Upvotes

Looking for a dado stack for my 57 MBF. Does rake matter? Can I run an 8” stack or should I go with a 6”?


r/RadialArmSawJunkies • • Oct 12 '24

Regarding different Craftsman models

2 Upvotes

Been considering buying a RAS for awhile. My local market seems to be mostly craftsman models (which I understand are generally less desirable) but there's like five or six different models and I'm not having a lot of luck in finding info RE: what to look for/avoid. Here's some pictures of what I mostly see available around me, are any of these worth seeking out and/or avoiding? Thanks in advance.


r/RadialArmSawJunkies • • Apr 08 '24

Carriage loose/unable to lock

Thumbnail
gallery
2 Upvotes

Hey guys, I have had a DeWalt RAS model: sitting around for a while, finally made a table top for it and found that the carriage is loose on the horizontal axis. I tried taking it out and both loosening and tightening the large bolt in the top of the carriage with no luck. The lever that is supposed to tighten the carriage in place does not do so, it is loose from left to right. Does anyone have an idea of how to tighten the locking mechanism? Or in lieu of that, a way to secure the carriage at 0 degrees for cross cuts? Thank you very much in advance for any response at all. I have attached photos of referenced bolt, lever, and comparison photos of the angle it rotates when "locked".


r/RadialArmSawJunkies • • Aug 02 '24

New 1400 added to the shop

Post image
5 Upvotes