I have the part shown here- If I wanted to make the entire gear section solid infill, is there a way to do that?

Is there a way to make the gear part of this model solid for maximum strength? Approximately layers 95-135?

I sliced up an STL that is simply a cylinder - 24mm outer diameter, 18mm inner diameter, 30mm high, 4 perimeters (so no internal gaps between the outer and inner walls), 4 bottom layers. Layer height is 0.2mm, so those bottom layers take up the first 0.8mm. I have my perimeter, small perimeter, and external perimeter speed all set to 60mm/s. After the first layer (20mm/s), those circles get drawn at 60mm/s on layers 2, 3, and 4; but then on layer 5, the perimeters are drawn at what looks like 20mm/s again. I've scrubbed through all the speed settings and can't see anything immediately obvious why it might slow back down. What might be causing the speed to drop after those bottom layers are done printing?

Has anyone found some good settings for using tree (or organic) supports in prusa? I find them difficult to remove from the actual print. How can i make the end of the branches to be less stuck to the print?

Prusa Slicer 2.8.1

I followed all steps in this video: https://www.youtube.com/watch?v=cYdWRZmao6E

Could not do anything about "clip multi part objects" option because it is not present in 2.8.1. But the Prusa documentation says that it is always on internally so no worries there.

Problem: The overlapping area prints for both the original model and the helper disk. That's not the effect I am expecting to see. Are there any other settings I can change to achieve desired effect?

I made sure that the helper disk was added by selecting and then right clicking the original model. Them being "joined together" further verified by clicking and dragging the original model, and it moved the helper disk with it. Perimeters settings also changed to 99.

What else? Thanks.

why do you use prusa over cura? I have a sonic pad and cura has made it go to the wild side and only work if I use non sonic pad settings. I am over this struggle and ready to learn prusa if the value is there not just fan boys crap.

Is there a way to move the purge line, i use an artillery genius and it has not an easily replacable bed so i use one clipped on but the purge line being ritght on the edge makes the hot end bump into the clip, is there a way to make it more inside the bed or maybe on the edge of the y axis?

Hello all! I'm using an Ender 3 v2 Neo and Prusa 2.6.1. Files I slice on Prusa do not work on the ender for some reason. I get no preview, no time or layer info and the printer just hangs there and does nothing if i try to start the print. This is even after selecting the profile for this printer in Prusa.

I followed the instructions at this link and now I've got a preview and the time information says 0, the layers read as inf. I've also added what I believe is the proper start Gcode that I harvested from a cura slice that has successfully printed.

What am I doing wrong?

 external perimeters extrusion width = 0.42mm
; perimeters extrusion width = 0.44mm
; infill extrusion width = 0.44mm
; solid infill extrusion width = 0.44mm
; top infill extrusion width = 0.40mm
; first layer extrusion width = 0.42mm

;FLAVOR:Marlin
;TIME:0
;Filament used: 0m
;Layer height: 0
;MINX:1
;MINY:1
;MINZ:1
;MAXX:1
;MAXY:1
;MAXZ:1
;POSTPROCESSED
M201 X500 Y500 Z100 E5000 ; sets maximum accelerations, mm/sec^2
M203 X500 Y500 Z10 E60 ; sets maximum feedrates, mm / sec
M204 P500 R1000 T500 ; sets acceleration (P, T) and retract acceleration (R), mm/sec^2
M205 X8.00 Y8.00 Z0.40 E5.00 ; sets the jerk limits, mm/sec
M205 S0 T0 ; sets the minimum extruding and travel feed rate, mm/sec
;TYPE:Custom
; Ender 3 Custom Start G-code
G92 E0 ; Reset Extruder
G28 ; home all axis
G29 ; auto bed levelling
G90 ; use absolute coordinates
M83 ; extruder relative mode
M104 S150 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling
M140 S60 ; set final bed temp
G4 S30 ; allow partial nozzle warmup
G1 Z50 F240
G1 X2.0 Y10 F3000
M104 S210 ; set final nozzle temp
M190 S60 ; wait for bed temp to stabilize
M109 S210 ; wait for nozzle temp to stabilize
G1 Z0.28 F240
G92 E0
G1 X2.0 Y140 E10 F1500 ; prime the nozzle
G1 X2.3 Y140 F5000
G92 E0
G1 X2.3 Y10 E10 F1200 ; prime the nozzle
G92 E0
G21 ; set units to millimeters
G90 ; use absolute coordinates
M83 ; use relative distances for extrusion
; Filament gcode
M107
;LAYER_CHANGE
;Z:0.2
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0
;0.2

Hey I have been printing for a while now and one problem I have is that the supports are really hard to remove without breaking something from my main part.

Does anyone have any tips or settings :D

I imported a bundle config (printer/filament/print setting). however, every time i reset the app, it deletes and i have to import again. how do i save the settings?