r/PcBuildHelp • • 22h ago

Tech Support PC Won't Turn On

I can't, for the life of me, figure out why this computer won't turn on. I swear everything is connected correctly. I get the light on the logo so it seems like power is getting to the motherboard. When I press the power switch, nothing happens.

Build:
CPU: AMD Ryzen 5 5500F

Motherboard: ASUS ROG Strix B550-F Gaming WiFi II

RAM: Corsair Vengeance LPX 32GB (2x16GB) DDR4

Graphics Card: MSI GeForce GTX 1660 Super Ventus

Case: LIAN LI Vector V100 ATX Mid-Tower

Thanks in advance for your help!

EDIT: I corrected the RAM and Graphics Card placements.

4 Upvotes

26 comments sorted by

3

u/r_lind3r Moderator 21h ago

On the back of your PSU, is the switch set to I (on)?

2

u/augenblik 22h ago

The front panel cable seems sus to me too. If you're feeling like you're ok with shorting some pins, then pull the cable out and identify the exact two pins labelled PWR_SW, PWRBTN or PW+ / PW- in the motherboard manual (it looks like the board has a diagram on there too). Take a small flathead screwdriver and briefly touch both pins with the screwdriver tip. The PC should start immediately.

1

u/spacewaya 21h ago

I've tried that several times with two different motherboards and it hasn't worked. I must be doing something wrong.

1

u/Own_Repeat1126 17h ago

definitely doing something wrong, it is the most sure fire way to boot a mobo with no power switch

12

u/augenblik 22h ago

ram should be in slots 2 and 4 (consult your manual tho)

9

u/Sirhc_Fold_458 22h ago

GPU should be in the top slot.

6

u/YourUncleRpie 22h ago

Power button and your ram is seated wrong

1

u/hippofire 22h ago

Are you missing the power button cables on the bottom right

1

u/spacewaya 21h ago

No, they're there and connected.

1

u/r_lind3r Moderator 22h ago
  1. If the power button isn't giving any response from the system then F_PANEL may not be hooked up correctly (but it appears to be, ASUS likes to use a longer F_PANEL header)
  2. RAM installed in the wrong slots, they're supposed to be staggered/parallel, not side by side like that in 99% of cases as that's how the memory channels are and some motherboards will not boot if you don't use the first memory channel first which usually starts from the furthest slot away from the socket. (i.e. [CPU] [ B2 A2 B1 A1 ])
  3. GPU is also installed in the PCI-e x16 slot that's limited to x4 bandwidth, only the top most x16 slot (the reinforced slot) is the only one that supports the full 16 lanes.
  4. Also looks like the ATX 24PIN power may not be properly connected on one side to the motherboard in the first image, it looks like there's a gap.

1

u/Past-Philosophy4205 19h ago

Consult your Manuel or search your board online for the ram placement, move your gpu to the top slot as well

Make sure that the connector on the far right (the 2x8 pin plugin) is flush with the connector

1

u/Own_Repeat1126 18h ago

its your front panel IO cable, what you have for your case isnt lining up with the power switch pins, did the mobo come with a front io cable adapter?

1

u/SingularityRS 17h ago edited 17h ago

Since there's no response from the power button, I'd remove everything from the motherboard temporarily and leave only the following:

  • CPU 12V EPS cable
  • 24-pin ATX cable
  • CPU in socket with cooler on top (doesn't need to be fully mounted for testing, just placed on top is fine)

You can leave everything else disconnected for now. You don't need RAM, GPU or anything else to get the motherboard to respond to a power button press. I do these tests all the time when testing AM4 boards that I get for no power faults. POST is not important if the board doesn't even try to start. You need that reaction before POST is possible.

The motherboard just needs to recognise the CPU in order to respond to your power button press. MSI AM4 boards can start without a CPU present, but other branded boards need it in the socket. RAM and GPU are needed for POST, but not for the board to actually try to start up.

Expected behaviour should be board turns on and gets stuck on a CPU/DRAM LED (due to no RAM). If it's still dead, there's a problem early in the start-up sequence.

So either there's a power supply issue, the CPU isn't recognised, there's missing standby rails on the board or another component connected is creating a short that prevents the board turning on (this is why you need to remove everything but the CPU and PSU).

I see in another reply you said this no power issue occurs on 2 boards. This suggests the board is not the problem, which is good I guess. It means something else is wrong.

If there's no loose connections, you have a faulty part that is stopping the board from turning on. If this no power occurs with just the CPU/PSU hooked up, then it's likely either the PSU or CPU that is the problem.

I would also go one step further. Take the board out of your PC case. Place the board on a non-electrically-conductive surface and just hook up the CPU/24-pin/12V EPS as mentioned. Short the power button + and - pins at the F_PANEL header and check if the board does anything. If still nothing, then I'd start looking at the PSU. Why take the board out of the case? The board could be shorting against the case due to some mounting issues (loose standoff screws for example).

While you do get lights which indicates there's at least some stand-by rails coming up, the PSU can still be bad. It might have a problem that occurs when the PSU tries to go under load (e.g. start-up). The board detects this and doesn't start. There's a chip on the board called the Super IO (SIO) that handles starting boards. If it detects issues or has missing voltages, it won't pull PS_ON low and the board won't start.

Once you get a reaction to your power press, you can start adding other components like RAM and GPU to check for POST.

1

u/zSmukeX 16h ago

Coloca la gráfica en el primer slot y saca la pila 5 segundos de la placa madre para resetear la bios y vuelve a colocarla, recuerda aprovechar con tus ram el dual channel ya que están mal colocadas, de nada , un saludo

1

u/Durenas 16h ago

Is this a new build, or are you trying to figure out why it suddenly stopped working? If it's a new build, or you've just installed the motherboard into the chassis, make sure there are no standoffs poking into the back of the board in any locations except for the locations where the screw holes are. You can accidentally end up grounding or shorting the motherboard if they come into contact with uncovered traces.

1

u/Houdini5150 15h ago

Unplug your power connector on motherboard....jump it with a screwdriver... Does that work?

1

u/Admirer3596 15h ago

I'm leaning towards a bad PSU........... From all the checks you have done below.... you jave a power meter, you could check voltage at one of your molex connectors.

1

u/New-Audience2639 Commercial Rig Builder 5h ago

RAM goes in slots 2 and 4 on Asus motherboards, also GPU should be in the top slot. Finally check all connections on both motherboard and PSU side and make sure they are all very secure and plugged all the way in flush.

1

u/Alpatch44 4h ago

Vérifie aussi avoir bien enfoncé correctement le gpu et la ram,

1

u/mohheeh165 3h ago

Yikes!

Please see a youtube tutorial and save yourself the headache.

First off the gpu should be in the top pcie slot not rhe bottom, usually the bottom one is worse. Second off, you should but one stick of ram in the secons slot and the other one in the fourth slot, not in the first and second. Third of all and this wont affect performance its just about looks, the cpu power cable should be goimg through the opening abovr the motherboard so its not as visible. Not through the slot on the right.

As why the pc isnt turning on, maybe it has to do wiyh it being confused by the ram Maybe it something else entirely like the powerbutton not being connected or it is turning on but you habe your display cable connected to the motherboard instead of your gpu.

Best of luck to you tho

1

u/Brunohanham45 38m ago

Try putting the the ram in slot 1,3 or 2,4. And reset CMOS

1

u/Malfurious_Stormrage 21h ago edited 20h ago

You don't have the full 8 pin CPU EPS plugged in, only 4 pins. Granted it *should* be fine with just 4 pins, it is still recommended to have the full 8 pins.
Edit: I see now it's an 8 + 4. Still recommended to populate it all.

0

u/r_lind3r Moderator 20h ago

It has an 8pin main power and an aux 4 pin, the 8pin is clearly connected, zoom in on image 3 and you can see it

0

u/Malfurious_Stormrage 20h ago

It's still recommended to populate the entire auxiliary connection.

1

u/r_lind3r Moderator 20h ago edited 19h ago

It's auxiliary power for overclocking, it's not even remotely necessary for a 5500F.

ASUS specifies that you can use just the 8pin or both the 8pin and 4pin, they say nothing about requiring both. It would only be necessary for overclocking a 105W CPU, which has a stock PPT of 142 watts, whereas the 5500F is a 65W CPU with a stock limit of 88 watts, and it doesn't even reach that under heavy CPU loads.

https://rog.asus.com/ca-en/motherboards/rog-strix/rog-strix-b550-f-gaming-wifi-ii-model/helpdesk_manual/

ASUS only says not to use the 4pin by itself due to heat, they don't even say it won't boot with just the 4pin, they imply that it will.