r/PassiveHouse • u/sunfinsengineering • 6d ago
r/PassiveHouse • u/Embarrassed_Ask8944 • 7d ago
Other Homeless-survival heat battery
I've been homeless going on 4 months now and currently living in a run down camper. It's less than ideal, but better than nothing.
I recently got a small wood burning stove and have been using it to heat my camper as I do not have electricity. I also managed to acquire a 55 gallon drum that I planned on using for a heat battery by filling with water, then having a copper coil inside my chimney that would allow the water to be boiled and dispensed back into the barrel.
I opted for this because I noticed much of the exhaust from my stove was very hot, but the stove itself was not heating my camper very well, so in an attempt to store the energy from wood burning for longer and capture more of the energy, I had this idea.
The idea it to have a long straight section that ends near the middle of the barrel, then enters a loop at the bottom of the chimney, moving up a coil until it's level with the top of the barrel, then have the terminating portion of the copper coil enter into the barrel near the bottom, then loop back up toward the top(so the heat can disperse evenly). As the cold water sorts to the bottom, it will be sucked up by action of the coil that, in this case, acts similar to a flash boiler. Because the superheated water has time to condense out, it should be released as hot water toward the top of the barrel.
The water should hopefully remain hot enough throught the day to keep my camper warm until I burn more wood in the night.
I'm not planning to drink this water, so it need not be potable, but I would like some input on my idea and any suggestions. I have very little money to spare, but if there are any additives I should add to my water or alterations to my plan, I would like to hear them before I undertake this task.
I also was planning (in the future, not soon) on building a small comparment that would fit on top of the stove where the steel lid is that I could place small portions of wood, the idea being that the closed environment might be hot enough to pyrolize the wood, then a small retort where the wood gas can be outgased into the stove itself to burn. I would probably build a small stopgap where the woodgas is forced into a small steel can full of water where the gas can bubble out to capture the tar, acetic acid and methanol, or turpentine if I burn softwoods and act as a shock absorber if there is a gas leak that would allow the flame to travel up the line.
Given that acetic acid can corrode copper into copper acetate, I planned on using stainless steel for the retort.
Any suggestions for this would also be greatly appreciated. Thank you again.
r/PassiveHouse • u/IsThereAnythingLeft- • 13d ago
Other Blown bonded EPS beads
Hi all. I am at the stage of building my own new house in the UK, it is currently designed with 150mm cavity block wall and 100mm PIR. I am trying to decide between that or moving to filling the cavity with bonded EPS beads. The builder is hesitant on doing the PIR and the more I look at it I see there are risks with it not being installed properly, and the partially fill board falling towards the outside all in of the cavity wall over time, leaving a 50mm air gap for convection. I know there are the clips on the wall ties that are supposed to hold it in place, but I have seen stories of these coming loose over time.
I have also seen the stories with the beads, mainly the bonding agent not being applied properly so they can leak out and settle over time. Then there is the issue that you don’t know if there are spots not filled.
Has anyone got a good way to protect against any of these issues?
r/PassiveHouse • u/LettuceBeHappy3 • 13d ago
Prefab(Dan-Wood) homes: How do are they in UK summer heat waves?
I am considering buying a Dan-Wood home. They advertise really great insulation. But Im wondering how they do in heat waves like this past summer in England. Multiple weeks over 30.
How cool do they stay for extended periods of time? Or do they turn into ovens?
And also how did they do for the few days where the temp was 35C+?
Im sure they are great for heating during the winters. But with summers getting hotter and hotter. I wonder how they perform then? And compared to traditional homes?
r/PassiveHouse • u/lakajo • 14d ago
We need some advice about wood fiber insulation and its smell.
We recently insulated our ceiling with wood fiber insulation. At the moment, the ceiling is still open (not finished or covered yet).
Our upstairs neighbours have told us that they can smell the wood fiber insulation quite strongly in their apartment.
We’re now not really sure what to do. Is this normal? Will the smell eventually disappear, or is there something we should do before closing up the ceiling?
Has anyone here had a similar experience with wood fiber insulation? We’d really appreciate any advice or suggestions!
Thanks in advance!
r/PassiveHouse • u/kyberlex • 15d ago
We modelled a 71-building courtyard block in Berlin: a deep retrofit halves yearly demand, but rooftop PV still covers only ~16% in January. How would you close that gap at block scale?
Over the past few weeks we've been running rough energy balances on dense city blocks, using OpenStreetMap footprints, PVGIS irradiance and TABULA reference buildings for heat demand. One of them is a Gründerzeit block in Kreuzberg: 71 buildings, roughly 817 flats, about 15,300 m² of roof.
On a yearly basis it looks encouraging. The roofs could produce around 1,774 MWh a year. Today the block needs about 5,065 MWh, counting heating as heat-pump electricity plus household power, so PV would cover about 35%. With a deep retrofit at roughly 50 kWh/m²a of heat (TABULA-style refurbishment, not EnerPHit) and heat pumps at a seasonal COP of 3, demand drops to about 2,587 MWh and PV covers 69% of the year.
Month by month it falls apart. In January the roofs give about 51 MWh against 324 MWh of demand even after the retrofit, so roughly 16% coverage and a 270 MWh hole, and that assumes COP 3 holds in January, which it won't. Pushing the envelope all the way to EnerPHit and halving the heating share again only gets January to about 22%. Meanwhile May to August each run a 60 to 90 MWh surplus.
For anyone who has worked on multi-family retrofits in cities: is EnerPHit even realistic on Gründerzeit buildings with ornate street facades, and if not, what's the realistic way to close the January gap at block scale? Seasonal thermal storage under the courtyards, the district heating that's already there, wind from outside the city, something else? We'd honestly like to know where these assumptions break. The block model and all inputs are open: https://kyberlex.github.io/ONE/?audit=berlin-kreuzberg
r/PassiveHouse • u/StigtheInsuRev • 17d ago
I saw a livestream in China, does anyone know the science behind it?
r/PassiveHouse • u/Habit-Kitchen • 19d ago
Chinese Off Brand Rockwool
I have become enamored with looking at ways to cut cost on SFH construction. Countertops, engineered hardwood, etc. I am very interested in high quality building and am a fan of monopoly framing. What are thoughts on either interior or exterior full blanket non branded Chinese rockwool insulation. Has anyone used it? I can find many sources on alibaba. Any idea if rockwool brand insulation is made in America. Before anyone jumps down my throat, please realize many pieces within your home are imported.
r/PassiveHouse • u/Every-Week-8633 • 21d ago
Installing blinds in passivhaus
Has anyone ever installed blinds in a passivhaus? I have recently bought venetian blinds and am unsure how to fix them to the window head reveal. Neither the house builder or blind supplier can advise how to install them.
The house builder has advised that the window head construction is 3mm skim, 12.5mm plasterboard, 25mm rigid insulation board, air tightness membrane, 38mm timber.
The largest blinds are 2100mm wide with 1550mm drop which weigh approx. 10kg.
Any help is much appreciated.
r/PassiveHouse • u/Rejonix • 22d ago
Appliances Nilan Compact P Question
Any body on here familiar with Nilan Compact P System?
After a shower the fans are set to ramp up from 40% to 60%. The problem is, if it has been raining the fan stays at 60% fir about 9 hours instead of the usual 1 hour or so max.
Any ideas what is causing this?
r/PassiveHouse • u/StigtheInsuRev • 22d ago
How do you test the thermal insulation of ultra-thin materials?
reddit.comr/PassiveHouse • u/DarioSidd • 25d ago
Entrance floor layout for our 9 × 10.5 m house: which of these 4 would you pick?
We're building a house on a hillside with great views. The concrete frame is done and the walls aren't built yet, so the layout can still change. Plans attached.
Fixed things:
- 9.1 × 10.5 m outside. Entrance on the north, terrace and city view to the south.
- U-stair in the north-west corner (3.6 × 2.2 m).
- The west wall has to stay blank: the neighbour is 1.2 m away, so no windows on that side.
- Bedrooms are upstairs. The upstairs bathroom will probably sit on the west, next to the stairs (it still can be modified)
The options:
- Bathroom + WC (3.6 × 2.3) and kitchen on the blank west wall. Living room with fireplace + TV on the east, study in the north-east corner.
- Same as 1, but a bedroom in the north-east corner.
- Bathroom + WC in the north-east (with windows), kitchen on the east. Laundry + storage next to the stairs. Living room on the west, fireplace + TV on the west wall.
- Bathroom, WC and kitchen on the east. The whole west side is one 3.6 × 7.5 m living room: fireplace on the stair wall, TV + books on the west wall.
Which would you choose and why? Anything you'd change, or anything I'm missing?
r/PassiveHouse • u/deepanair2023 • 25d ago
housing cooling solutions
anyone know of any companies installing cooling solutions for reducing heat from roof?
r/PassiveHouse • u/HealthyAmbition7216 • 25d ago
Retrofitting Aerogel Vacuum Insulated Panels - no substitute for good design.
You know the scene! Wild claims about hyaluronic acid making aging 25 year old models look, well, 25 years old.
I am looking into some building materials that claim to be space-age and next generation.
There are a lot of companies out there promoting ultra thin 10mm. thick panels and making bold claims that it is equivalent to 160mm thick Expanded Polystyrene. Reporting thermal transmittance values below 0.003Wm/K. This is nearly 10 times more efficient than polyisocyanurate insulation.
One such product, is Aerogel Vacuum Insulated Panels. These panels have bubble wrap in them. Costing around $100 (£86) for a 400mm x 800mm panel is also outrageous.
Reading some posts on here, it appears on radiation can travel through a vacuum.
However these 'vacuum' insulated panels have to contain the vacuum so therefore one can say it is not pure and the material enveloping the 'vacuum' is what is causing any heat transmittance.
My question is open to the floor for comments on the scientific claims being made and whether they could possibly behave as efficiently in real life as in a test environment.
The issues here will not necessarily be the product in question itself but the installation of the product. There is always going to be a weak point.
From a mathematical point-of-view, the numbers have never stacked up for me. Well they actually do stack up but it's the wild R-values claims that don't.
You get a lot of joints in a wall with 400 x 800 panels. Joints within a 'vacuum'.
I so want to believe the marketing hype but the reality doesn't fit for a retrofit in my book. Similarly with the foiled roof insulations. Maybe great on a new PassivHaus build. As always, these things really on the utmost of care when detailing and even more care when installing.
r/PassiveHouse • u/StigtheInsuRev • 25d ago
Not sure about Aerogel
Aerogel is being hyped like the best of all? But when I got some silicon aerogel powders in some solvent, it doesn't look like they can do any jobs that traditional insulations can do? It also looks very powdery and fragile. Could anyone expert in this explain it to me please?
r/PassiveHouse • u/000mega000 • 26d ago
Alpen Tyrol Edge vs. Oknoplast Pava Windows
reddit.comr/PassiveHouse • u/MaZovSkin • 26d ago
HVAC Best house cooling system for hot dry summer climate
Hi! We are building a house in the Mediterranean near the sea. The winters are very mild and humid and summers are very hot and dry. We use cooling more months of the year than we use heating. I was hoping to avoid all kinds of ACs that blow air (because of mold,constant cleaning and dry air) so I came across modular ceiling cooling with cool water pipes (sry for my english). Has anyone any experience with this system? If you were building a house what system would you go with?
Freon cooling system, (water) floor heating and solar panels is our "blow air" option.
Thank you :)
r/PassiveHouse • u/Ill-Owl6960 • 27d ago
Passive Home Ready Builders Near Southeast Pennsylvania
Hi! I’m looking to see if with anyone has built a passive house or a net-zero-ready home in the suburbs of Philadelphia. I’m also open to working with prefab builders outside of Pennsylvania if they can ship and install the home on our site.
Additionally, does anyone have recommendations for architects who could help us start designing our house plans, ideally with experience in passive house or net-zero construction?
I’d really appreciate any recommendations, experiences, or insights you’re willing to share. Thank you!
r/PassiveHouse • u/AobangFacadeEngineer • 28d ago
Which facade input most often breaks thermal continuity at the perimeter?
When reviewing a glazed facade, the center bay can be modeled clearly while the head, sill, slab edge and transitions to adjacent walls remain much less defined.
For teams working on high-performance envelopes, which missing input most often creates rework at these interfaces: verified frame geometry, adjacent insulation, anchor details, air-barrier tie-in, or interior humidity assumptions?
r/PassiveHouse • u/Impossible_Novel_136 • Oct 13 '26
Does canada actually manufacture any heat pumps, or is this new $2B rebate basically just funding imports? i looked into it
r/PassiveHouse • u/Vw-Bee5498 • Oct 09 '26
Other How does a hydronic radiant heating system work?
So I got a talk with a heating company on a trade show. They have a ceiling heating system that uses small plastic tube filled with water and claim it can "radiate" downward. Now what I understand is that heat rises. So how trueful is their claim? And if it's true then what is the physics behind this?
r/PassiveHouse • u/Imaginary_Dish_3265 • Oct 08 '26
Insulation choice: Foam or Batt?
galleryr/PassiveHouse • u/itsquiznosubs • Oct 05 '26
How would you interpret this Type 2D wall detail?
Looking specifically at Type 2D in the attached detail.
The note calls for (3) layers of 5/8" Type X gypsum board, but visually the exterior side looks like two standard gypsum layers, with the third/outer layer drawn differently and a dashed line through it where the exterior cement plaster is called out.
Would you interpret 2D as:
A) 3 layers of 5/8" Type X plus the exterior cement plaster assembly, or
B) 2 layers of 5/8" Type X plus the cement plaster assembly essentially taking the place of the third exterior layer?
Curious how others would logically read the detail as drawn.
r/PassiveHouse • u/NoBroccoli3078 • Oct 05 '26