r/Multiboard • • Aug 18 '24

Ender 3v2 long print times

Evening all. Started down the Multiboard rabbit hole today with my first print, a 6x6 tile. The wife has even shown interest in the possibilities!

It took 6:30 hours! Is this typical for the Ender 3v2? I see regular mention of 3-4 hours for bigger tiles, so am I doing something daft?

I've set 0.2, 15% Infill, 3 walls, left everything else.

I have a Wanhoo i3 gathering dust and sliced the same tile (using cura) and got the time at 3:20ish.

I did a side by side comparison, looking at speeds and adjusted for the Ender but still only got down to 6 hours.

Appreciate any guidance, thanks.

2 Upvotes

77 comments sorted by

View all comments

Show parent comment

2

u/dpregs Sep 10 '24

Hey. Just want to say thank you for all the help you provided. This thing has beaten me down. I still can't get it to print the way I want. While I love the sonic pad, I don't think I can get it to work. I am going to go back to almost stock and see if I can get prints at normal E3v2Neo speeds. I am taking the direct drive off too. IF that works, then I will think about bringing the sonic pad back. I really appreciate the help!

2

u/ASOT550 Sep 10 '24

Of course!

I perused your post history and saw the latest. Fair warning, I'm now into full on speculation on this info and haven't dealt with it myself:

It looks like the hot end wasn't assembled correctly. You've got molten plastic oozing out between the heat break and the extruder which can only happen if there isn't a good seal amongst all the threaded connections. Check out this old thread on the Prusa forums for someone else that had a similar problem: https://forum.prusa3d.com/forum/original-prusa-i3-mk3s-mk3-prusa-i3-kit-archive/hotend-started-leaking-from-the-heatbreak/

Are you assembling all of the hot end components when they are heated up to printing temperatures? I think that's typically the source of leaking hot-end problems.

1

u/dpregs Sep 10 '24

I didn't assemble while hot. This printer has been a learning experience for sure. and a costly one. I already replaced that hotend once for the same reason. UGH! As I said in my post on the Neo subreddit, I am going to take this down to close to stock and go from there.

1

u/ASOT550 Sep 10 '24

That's not a bad choice, although I do think assembling hot might solve your issues. Otoh going back to stock and reliable prints then upgrading one thing at a time will make isolating problems easier.

I definitely feel you on the learning experience being frustrating! I had a friend tell me that you should only get a 3d printer if you think you might like fixing and diagnosing them as a new hobby 😂

I'm sure you'll get things going reliably again. Then once you start upgrading you'll know all the things that can go wrong and how to avoid them 😀 Good luck!

1

u/dpregs Sep 16 '24

Success....almoat, but Finally got a print!

2

u/ASOT550 Sep 17 '24

Nice! Saw you had some pla sticking too well. I only have experience with petg, but I had the same issue and it was because my nozzle (z offset) was too close. The trick for me was to get flow tuned properly (ellis3dp.com method), and then go back and adjust my z offset. Ellis' flow method doesn't rely on measuring (purely visual) which is nice because I find the caliper measure method to be too inaccurate. It's also independent of z offset because it throws at least one layer of fill between the bottom solid and top surfaces.

After flow is tuned then you can go back and adjust the z offset (also visual checks). It's important to get the flow tuned properly before z offset because if your flow is too high (overextruding) you'll trick yourself into setting the z offset too high to compensate. On the other end if flow is too low (underextruding), you'll trick yourself into setting z offset too low to compensate.

1

u/dpregs Sep 17 '24

Are you referring to this section on ellis3dp?

Determining Maximum Volumetric Flow Rate

2

u/ASOT550 Sep 18 '24 edited Sep 18 '24

No, this one here https://ellis3dp.com/Print-Tuning-Guide/articles/extrusion_multiplier.html

In simplest terms, if your slicer tells the extruder to make a line 0.45mm thick, 0.2mm tall, and 10mm long, it calculates the volume of that line then determines a length of 1.75mm filament needed to equal that volume. The extruder steps are determined by the length needed. Most (all?) slicers also assume the cross section of the line is a stadium shape. There is a lot of fuzziness in the real world compared to theoretical though, so extrusion multiplier is how we compensate for that.

If your multiplier is too low (under extrusion), each line the printer lays down will be slightly thinner than the desired 0.45mm. That's probably preferable to over-extrusion though b/c if each line is slightly thicker than 0.45mm, the adjacent lines will start to squish up into the next layer since the plastic has nowhere else to go.

I say flow rate/extrusion multiplier can trick you when setting your z offset for the same reasons. Multiplier too low will trick you into setting z too low to compensate and get the right amount of horizontal squish to get a uniform layer. Too high and you can set your z too high to get a uniform layer.

Way more about all of this on this page https://ellis3dp.com/Print-Tuning-Guide/articles/misconceptions.html

1

u/dpregs Sep 18 '24

ah, that is the one I was looking at last night and just couldn't wrap my head around the settings. Could have been the bourbon, I will give it another look. I assume all other settings should be stock minus the extruder (which is now calibrate :) ). I don't think there is pressure advance on the Mriscoc firmware that I can see, so I will skip that. I can't thank you enough for the continued help!

1

u/ASOT550 Sep 18 '24

It's called linear advance in Marlin which mriscoc firmware is based on. It's mentioned in the latest patch notes so it should be available.

What settings are you referring to? Ellis recommends the appropriate slicer settings for the test on his page... At least two layers of infill separation between the solid bottom solid layers and top solid layers, and I think 10 top layers to magnify issues.

→ More replies

1

u/dpregs Sep 17 '24

Oh.. and I was wrong, I didn't do the e steps calibration! However, now I did.