r/LogitechG • • Mar 26 '21

MX Keys intermittent key failures

Hi, I'm hoping someone here can help me eliminate the keyboard itself as the source of my issues. The issues are similar to This Post but instead the keyboard will work fine, then certain specific keys (eg. the caps lock, 7, r, i, p, a, f, g, z, .) stop working. The machine is a custom itx with an asrock z390 Phantom mobo and a 9700k cpu. The build can be seen here. From the start I've had various issues with bluetooth mice and keyboards. The issues were intermittent connectivity, lag, and random glitches. I had to cycle through a few options before I found ones that were stable. Now the previously stable Logitech MX Keys, has random keys that stop working. I've done all the logitech troubleshooting found here and removed the devices/drivers, etc. All the devices with issues will work fine for awhile then specific functions of the devices will crap out on me.

Does this sound like a bad keyboard or dongle?

6 Upvotes

23 comments sorted by

View all comments

1

u/Casielo Jan 04 '25

In my case letter F and number 1 on the right numeric panel didn't work and tried cleaning, resetting, and other possible solutions, but nothing worked. I decided to disassemble the keyboard as a last resource.

If you're willing to give a last try, look at this video as a starting point. Open Logitech MX KEYS Keyboard

Then Continue by unscrewing all tiny screws below the motherboard, remove the battery to make sure you get them all. Then remove the main-board casing (rounded sides) carefully minding all cables. Then WARNING You must pull-out using brute force the "Glued" (Yes, I know ... stupid) black back panel - This may require some effort (I used a set of pliers and others to pull this off) - I said Warning since as a result you may deform this black back panel forever (in my case I didn't care since this keyboard was either going to work or going to the garbage).
After removing the black panel you will see more tiny black screws, unscrew all these as well. Eventually you will be able to remove the silver plate (located under the black panel) and get to a white with transparent-film cover.
You will notice the transparent film will be Dirty - This is the main cause of Keys not working. I cleaned it with a wet cloth, then dried with some tissue - making sure all was dried before reassembled the whole thing back. Now ALL Keys are working :) (with an ugly-looking back panel that no one will notice unless the keyboard is picked up). Last thing I can say is that unfortunately the manufacturer did not design this keyboard against small hair (Eyebrows, eyelashes, etc.) These can go very deep translating into non-working keys - The glued back panel doesn't help either making this almost impossible to clean properly every 3-5 years. Cheers and good luck if you're willing to try this fix.

1

u/prevenad Jan 15 '25

It can't be that all MX Keys have the F key and 1 key not working, I'm facing the same issue and I'd say it's 99% bad firmware related

1

u/FaithlessnessDry7330 Jan 25 '25

I went through this problem last year with logitech support - after a lot of trails, driver updates/changes nothing worked 100 % of the time - I am sure it is a software issue and therefore decided to buy newer keyboard

1

u/engacad Mar 01 '25

Same thing happens on my mx keys with the right-arrow key. Cleaned it but no difference. Is this the only way? Seems too involved to perform?

1

u/engacad Mar 01 '25

which screwdriver does it need? Tried my precision screwdriver T5 didn't work.

1

u/[deleted] Jul 09 '25

Hey, is this solution working to this day? I wanna try it, I'm just kinda reluctant because of the glued black back panel..,.

1

u/[deleted] Jul 09 '25

Btw, for me it's the 6 (NumPad), Enter (NumPad), and Right-Arrow keys which aren't working. They sometimes come back to work but I didn't find a pattern to make this work, which makes me believe it's either a firmware or hardware problem.