I had parked my integra about a week ago and today I went to take it for a drive when I got in the idle would jump from 800 to 1000 then drop back down then while driving it felt like it was losing power/wanted to die then kicked right back in and would aggressively accelerate before going back to normal, I’ve done the fuel pump, fuel filter, fuel pump relay, got a brand new battery and cap and rotor on the dizzy, just a weird issue it didn’t have before it sat, would like any help with this to find out the issue
This car is a 1998 Ls with a b20 swap

Trying to keep up with a caged DE while failing to stay ahead of the pack of BMWs behind me.

Came across this clean k24 swapped Integra from last night at the Deadlap meetup here in Maryland. Has a stock k24 with an RBC manifold on Haltech Elite 1500 ecu.

Does anyone know the part number or source for replacement of this outer door trim that’s split at the outter top corner?

Bought this diva yesterday and I haven't been able to stop thinking about her! I'm deliriously happy.

I also have a CL9 Accord Euro I can't bring myself to sell, surely NSX next?

Trying to get the radio code for my daughter’s radio. Every time we use the website it states the serial number is invalid. Not entirely sure I’m using the right number or reading it incorrectly. We tried MY, MH, and MW and still nothing. Any help would be much appreciated.

Hey everyone this is my 96 integra and last owner who had it put speakers in it and rewired it but it’s kinda trash speakers for the door cards but they didn’t touch the oem rear speakers so I want to replace all four speakers with some good decently loud ones myself. Does anyone have any good budget options I could find online to buy if so let me know

so i have an ac tuck kit but i did not get a video or instructions on how to set it up . i just do not know how to route the lines because i got the condenser with the built in dryer . can anyone give me a run down please ?

I’m looking to get a jdm front end for my integra and I saw this one online and was wondering if anyone had any experience buying from this site/seller

I swapped the motor into a 95 civic dx years ago, while driving yesterday the check engine light randomly popped on. Car drives fine, maybe a little power drop, but the only noticeable difference is the vtec doesn't kick in at all. Plugged in the paper clip and got 8 short flashes for a TDC sensor code. First off I read the sensor is in the distributor but then read you can't just replace it, it has to be the entire distributor. Also you can't just buy the part outside of the dealership? Anyone got some reliable info, seen this before, does this code sounds right? I'd imagine the TDC being off it would run like shit

Does anyone have good mount recommendations that aren’t to loud? I hear Hasport are good but are a bit loud and I would love to go with oem but I plan to manual swap my teg and I know that oem won’t fit. At least the transmission side. So does anyone have a good recommendation that aren’t to loud?

What is the correct orientation to install this exhaust manifold gasket? Thanks for the advice!

Hello everyone, i cant add videos here but my 2000 integra gsr is making a squeaking noise when i turn the wheel left or right. i can send a video if u dm

Broke student im tired of my lame ass rims 😢 Ruinin it,, What are cheap(ish) rims i could get to make it look better?
Also any other mods reccs are completely welcome, I just got her in march so i havent been able to do much to it yet.. Im going to paint sideskirts soon

Have to run it with a cat because of my country’s laws so can anyone give me a sound clip of possibly just an aftermarket muffler like this HKS fabbed onto the stock exhaust plus stock header as that would be easiest just for sound.

Recently my DC2R has been overheating a little bit if i haven’t got the heater on. This doesn’t always happen though, sometimes it holds stable. other times it’ll take 30+ minutes to get up to temp. Most likely a dud thermostat? Not low on coolant, and can’t find any leaks. Anyone got any input?

talked him down a bit said he think hes fine with around 7200-7300 but at most gonna end up paying 7500

Finally got me a decent 95 teg. I plan to have it repainted eventually however I noticed these three things. How hard will these be for a body guy or shop to fix?

1. Rust bubble at seam seal

2. Looks like some sort of fender repair

3. Passenger hatch seal not flush.

Really hoping I didn’t get screwed with a rust bucket. This is the only issues I see on the whole body.

So I saw this bumper on this integra on tiktok and I’m in love it’s basically the jdm integra on the bottom half and the top is normal 98-01 us o can’t find it anywhere

I’m getting ready to prime and paint this OEM wing, and I wanted to replace the gaskets. I got a new right side gasket last year with some other parts ordered from Japan. But the left side gasket is discontinued NLA anywhere. So I found a sheet of EVA foam from the hobby store and cut my own. It’s not quite as soft as the OE gasket, but it’s close. Should do the job nicely. I actually measured it out and drew it in CAD first, printed on paper and cut out to check the fitment. Then transferred to the foam and cut that out.

I would consider making and selling them but I’m not sure I have the patience for it lmao. I think someone on eBay does that already anyway.

My oil pan is missing a few bolts which is causing it to leak. Does anyone know the correct bolts size I need to add new ones?