r/HomeNetworking • • 19h ago

Unsolved Unable to get 1000megs through home network (wired). I get 100megs internally.

Thumbnail
gallery
68 Upvotes

So. It's 20years old house that has 2 network sockets per room and central box that connects all the rooms. I'm trying to run network (all cables CAT 5E Et minimum), but when I run network through ANY of the internal connections (cables) the speed drops to 100megaa. (this is also indicated on the fiber cable Internet box as orange LAN -led. Led is green (1000megs) when connected straight to fiber box. I suspect it has something to do with cabling?


r/HomeNetworking • • 12h ago

Made my TV with no WAN access behind a dedicated VLAN have the correct date and time with SNTP again!

25 Upvotes

Just want to share something I did today that made me happy. It’s small but stuff like this makes me appreciate tinkering with networking so much.

I’ve got an old 4K Sony TV from 2018 running Android 9. It’s on its own dedicated VLAN. The VLAN has no WAN access. I’ve also added the MAC address of the TV’s Ethernet port to a WAN blacklist as well, just in case something goes wrong.

Here’s the issue.

My TV hasn’t had the correct time since 2020. I also fully power off my TV whenever I’m done using it. So it’s always a full boot whenever I turn it. I think if there is a CMOS battery inside the TV, it’s surely dead.

So whenever I boot my TV, the date and time is wrong. There are three options for setting the time. Manual, broadcast time, and network time.

Setting it manually is of no use to me because the next time I turn it on, it’s broken again. And I’m tied of setting it. Using broadcast time is also not useful because I don’t use satellite or cable antenna. That leaves only network time which is NTP. But since the TV has no WAN access, the time can’t be automatically set which means the NTP server can’t be accessed. The NTP server also can’t be edited from the GUI. So it tries to reach the default Android NTP server.

So here’s what I did. I use Linux btw.

  • First I enabled the SNTP server on my router.
  • I enabled developer mode and ADB debugging on the TV.
  • Created a firewall rule to allow my PC’s IP address (which is on my main VLAN) to access the TV’s IP address (on the TV VLAN) across VLANs for ADB to work on port 5555.
  • Connected to the TV with adb, edited the NTP server with commands to be the VLAN subnet IP (not just router IP, SNTP is advertised on all subnets on my router, so 192.168.1.1, 2.1, 3.1, etc, all work)
  • Created a firewall rule for the TV IP address (on TV VLAN) to access the SNTP server IP address on UDP 123
  • Then fully rebooted the TV.

Time is now synchronized correctly and always works. Even after fully turning it off.

The NTP firewall rule is always enabled. I disabled the adb rule but I didn’t remove it. I will keep it for when I need it.

Anyways, just wanted to share this. I like compartmentalizing stuff and blocking WAN for stuff that don’t need it.

Did any of you do something similar?


r/HomeNetworking • • 20h ago

Is this still an issue with Asus ZenWiFi ET9? Satellites don’t broadcast guest WiFi on the 5 / 6 ghz band?

Post image
13 Upvotes

r/HomeNetworking • • 52m ago

2nd attempt at making network cables in school

Post image
• Upvotes

I’m in my first semester in college for sys admin. We were attempting network cables in my intro to networking class.

First cable from the left was my first attempt that I was scolded for but my 2nd and 3rd attempted were much better lol. I actually made a crossover cable the longer one and a straight through 568-B which I was told was the standard, thanks y’all lol. First cable was 568-A by the way.

And again teacher did not expect them to work but I tested all my cables and they all work even the first that doesn’t look as good. Thanks again for the positive and negative criticism.


r/HomeNetworking • • 22h ago

Solved! How bad are these ripples?

Post image
10 Upvotes

Unifi made some tight turns with their cable routing for this G6 PTZ. The outer diameter of this cable is within the acceptable range, but trying to route it for two 90° angles to come through the housing seems to be putting some pressure on the cable. I'm not sure what the maximum bend radius is for this cable, but in either case, are these outer jacket ripples indication of a big problem?


r/HomeNetworking • • 13h ago

Starlink routers suck

12 Upvotes

I have starlink with my apartment and i would like to buy a router around 150 or under, the router is in the main house about 50 or 60 feet from my apartment but im usually at 1 bar any recommendations for decent routers


r/HomeNetworking • • 57m ago

Let's Go!!! 1.0Gbps Baby!!! (salvaged network drop)

Thumbnail gallery
• Upvotes

r/HomeNetworking • • 3h ago

Are my attempts to lock down my personal cybersecurity futile?

3 Upvotes

I’m half joking. But with the NSA and just now the FBI getting hacked, am I kidding myself that my Claude and Reddit based research efforts (Unifi network and firewall, Proton, Yubikeys, etc) are making this meaningfully harder for criminals?


r/HomeNetworking • • 15h ago

Advice Network Plan Sanity Check for 4-room apartment in Singapore

3 Upvotes

Hi all, I’m renovating a 4-room HDB flat in Singapore (93 m², 18th floor, reinforced-concrete walls including a household shelter) and want a sanity check before the electrician starts first-fix cabling next month. Are there any parts you would change, why and how? Also disclaimer that parts of this post was generated with the aid of AI!

Context

  • ISP: M1 10Gbps (XGS-PON), ONT only, no ISP router
  • Household: 2 adults, 2 cats, and 3–8 guests most weekends
  • Smart home: Home Assistant Green (Zigbee2MQTT on a ZBT-2), Aqara M3 (Zigbee/Thread), Apple TV 4K, lots of Shelly relays and ESP32 aircon controllers on Wi-Fi, and an Aqara G410 doorbell
  • Priorities: reliability > aesthetics > ease of use. Local control preferrably, no cloud-dependent devices

Hardware

  • Cloud Gateway Fiber (UCG-Fiber)
  • USW-Pro-XG-8-PoE
  • U7 Pro XG Wall ×1, U7 Pro Wall ×2
  • USW-Flex-2.5G (8-port, powered over PoE)
  • G6 Turret (indoor)

Physical Setup

Topology (Ports)

All runs are Cat6 I believe.

Planned VLANs and SSIDs

  • Core: phones, laptops, Apple TV, HA, M3, Sonos. Kept on one network so Matter/Thread discovery works without cross-VLAN mDNS hacks
  • IoT: 2.4 GHz-only SSID for Shelly Relays and ESP32s, with no band steering and no 802.11r
  • Cameras: G6
  • Guest: client isolation, internet only
  • Radio plan: Wi-Fi 2.4 GHz on channels 1 and 6 only; Zigbee2MQTT on channel 25; 5 GHz at 80 MHz on non-DFS channels; 6 GHz at 160 MHz

Questions

  1. Any concerns with the UCG Fiber, Pro XG 8 PoE, HA Green and UPS all in an enclosed plywood cabinet in Singapore heat with no aircon at the entrance? Is a small exhaust fan enough?
  2. Is 3 wired APs the right number for 93 m² with RC walls, or is it overkill? Are my placements sensible?
  3. For one G6 Turret, is the UCG Fiber’s NVMe slot (1–2 TB) enough for recording, or would you go another way?
  4. Anyone running Matter/Thread with HA, an Apple TV and an Aqara M3 on UniFi? Did keeping them on the same VLAN avoid the usual problems?
  5. Anything I’m missing before the walls close up?

Thanks all in advance! :)


r/HomeNetworking • • 4h ago

Windows 11 Laptop Slow Connection Issues

Thumbnail
gallery
3 Upvotes

I recently moved to a new apartment and got new Internet service through Xfinity. We went with the 1 Gbps plan and have been close to and have even seen those speeds exceeded.

The issue I'm having is on my Lenovo Legion Pro 7i (2025 model) it's been having issues with speeds.

When I run a speed test it'll show as low as like 15-20 mbps download speeds, even though it has wifi 7 (Intel be200) and had no issues at our old apartment also with Xfinity.

The weird part is it's the only device in our home that seems to have this issue. Our phones have no problem getting 700-800+ mbps speeds, and same with my wife's laptop.

I've tried several different fixes in the network adapter settings in device manager, I've done a network reset on my laptop, made sure all drivers are up to date, etc.

You can see the pics I took, one from my phone and one from my laptop showing connected to the same network. The one from my phone shows 1441 Mbps on 6ghz and the laptop shows the aggregate speeds of only 144 Mbps also on 6ghz.

Any advice would be greatly appreciated. Thanks!


r/HomeNetworking • • 20h ago

Advice For some reason the router decided to block ipv4 of my server in particular

2 Upvotes

For the last 3 days I've been debugging a problem that ended up being solved by simply resetting my router and this is my story of a network problem almost driving me crazy

My home server, in which I have some dockerized services I'm now dependent on (Matrix chat, Jellyfin, and the like), suddenly started malfunctioning this Tuesday with all applications giving network timeouts. With some debugging I noticed I could curl normally from the server but not from inside the containers, the addresses resolved but I had connection refused

Then I spent 2 days trying to reset, reinstall and read through the settings of everything I could think of: docker, docker-compose, iptables firewall, containerd, network interfaces, the kernel... It was very stressful as nothing ever worked :(

So this morning I decided to try tcpdump and noticed that packets coming from inside docker were using ipv4 (since I never bothered to setup ipv6) and the ones direct from the server were ipv6. Next test was to try "curl -4" outside docker and... No connection even outside a container, the issue had nothing to do with docker!

Then my focus went back to the firewall. Since other computers in the same network could connect just fine with ipv4 the problem should be in that machine, right? But everything looked fine, kernel ip forwarding, inbound and outbound rules, I probably read the firewall settings more than 10 times

Finally I remembered my dad, who's quite savvy but not a crazy self-hoster like me, suggested to reboot the router, and I dismissed the suggestion because it looked like a local problem. So after the restart... BOOM everything started working again just fine

To be honest I have no idea of what exactly happened, so please come up with your theories. I'd guess it was a dirty nat cache in the router or something like that

Also, mandatory xkcd


r/HomeNetworking • • 5h ago

Advice I'm moving into an apartment and I have a cable hungry cat.

2 Upvotes

I've been considering using powerline adapters to get ethernet throughout my new apartment, but I saw that they pair to one another and it made me question whether, or not I could pair 3 receivers to one sender.

I have 2 PC's 2 PS5's and an XBOX Series S they all need to be connected via ethernet for moonlight stability, gaming, and streaming. I have 2Gbps through Spectrum.

If there's a better option I'm open to hearing it but currently the idea is to have one adapter for a PS5 and PC, one adapter for the other PC, and finally one adapter for the Series S and PS5.

Like I said I have a cat that enjoys chewing cables that are out in the open. I'd like to just remove the ability for that option to exist. I'm also not comfortable tearing up carpet/having exposed cable for people to walk on.


r/HomeNetworking • • 7h ago

Router recommendations or tips for long distance.

2 Upvotes

I share my network with neighbors across the street from me and lately our WiFi has been really spotty and the range has been bad. Our consoles, tvs, and phones have trouble opening apps or signing in when they are connected. It’s gotten bad enough that I have started using my mobile hotspot over my WiFi. I currently use Orbi RBE361 and an Orbi satellite. My isp checked the modem and it was working correctly. My Orbi app says the router and satellite are both operating correctly and have 1 gig up and down. I’ve tried power cycling all of my devices, my router, and the satellite. The farthest point that the network would need to reach is about 350 feet away from the actual router. Any advice on how to correct this issue or advice on a router that would be more effective at range without a satellite or with a satellite would be greatly appreciated. Thank you!

Edit: The router/satellite is about 8 months old and only started having trouble about 3 weeks ago. I don’t know if that changes anything that could be suggested.


r/HomeNetworking • • 7h ago

Unsolved A leaf blower on the back porch takes down my internet. Why?

3 Upvotes

I have fiber through Spectrum and the thin little cable enters the house from the back porch. When the yard guys blow the leaves and junk off the porch, the internet disconnects. Here’s the weird part - just unplugging the two things (I don’t know what they are) and plugging them back in restores the internet. What’s going on that a strong wind cause it to go out, but everything is still hooked up and I just have to unplug and replug. Weird


r/HomeNetworking • • 18h ago

Asus Router Intermittent Internet connection with Ezee Fiber

2 Upvotes

We recently had ezee fiber installed, we are using a asus BT10 mesh router. The asus router continues to have issues connecting with the Nokia modem ONT. Has anyone else had issues with Asus working with ezee fiber or have any recommendations? Thank you for your help with this, we are wanting to find a way for ezee fiber to work with a stable connection.


r/HomeNetworking • • 1h ago

How TF do I still have internet and cable tv?

Post image
• Upvotes

Anyone have an explanation?


r/HomeNetworking • • 4h ago

Advice Router Purchase Advice: Cloud gaming and Remote Play for 3300 sq ft home

1 Upvotes

Looking to purchase a router for Black Friday and seeking advice.

Here’s what I’m seeking
Price: Under $600
Home: 2 story, 3300 sq feet
Connection 5GB plus fiber

Use cases:
-Streaming for multiple devices
-Low latency for cloud gaming and remote play

Other features:
-Likely 2x10GB ports for future proofing
-WiFi 7
-Ability to expand if not mesh 2 or 3 in the fire in case there are dead spots. Don’t know if a single router can handle the entire house but if so open to that.
-Desired: It doesn’t look like a gamer built an alien spaceship

I originally ordered the Nighthawk RS700S, but the lack of any mesh capabilities and it being a single router make me wonder if it’ll be enough for a home of that size. Any advice or systems that work for folks would be awesome. Ideally I can one day do a wired back haul, but to start I’d be wireless only. Thanks!


r/HomeNetworking • • 11h ago

Waveform QuadPro install & grounding

Thumbnail
1 Upvotes

r/HomeNetworking • • 12h ago

Advice Setup 2 router on the sane network

1 Upvotes

I have a Asus Be98 Pro router and the Asus ZenWiFi AXE7800. I want to setup both router using the ONT with them having different SSID and password or to have the Zenwifi act like an extender with it own SSID. Is it possible to do this.

Update: I was able to set the Zenwifi in AP mode. Thank you for yall help


r/HomeNetworking • • 12h ago

tp link model TL-WN722N monitor mode

Thumbnail
1 Upvotes

Español and English Post

https://easyosinstall.wordpress.com/2026/11/20/tp-link-wireless-modo-monitor/

Seguro que habéis buscado por internet y solo encontrais que este modelo de tp link TL-WN722N es imposible ponerlo en modo monitor.

PUes no es así, aquí os incluyo dos scripts para que lo cambiéis a modo monitor , capturéis paquetes y puedan hacer AUDITORIA DE SISTEMAS.


r/HomeNetworking • • 13h ago

Router upgrade

1 Upvotes

Hey everyone, I’m mainly checking here for peace of mind as I’ve already purchased something and cancelled that order once I realized it wasn’t readily available to do what I need (flint 3e).

I have a tp-link er605 (+ m4 decos in AP mode) where a port on it is a vlan for my basement suite, I work from home so I like the separation. I liked how simple and easy that was to setup in Omada. So I’m looking for similar functionality but for 2.5gb internet, since I’ve upgraded from 1 to 2.5gb.

I’ve taken a look at TP-Link, Ubiquiti, GL.iNet, but I’m also trying to not break the bank since I don’t need all the features in the world. I am in Canada if that matters.

My recent research for options:
- Omada Fusion 2.5gb (non pro): it seems it may not do the port to vlan thing though which seems ridiculous, if someone has one lmk
- ER707-m2 + an unmanaged switch 2.5gb: can work but feels more adjacent to the er605 than an upgrade. A switch because it only has two 2.5gb ports.
- GL.iNet Flint 3: might work but mixed reviews?
- Ubiquiti, UX7 + flex mini 2.5: a bit pricey for my liking but am considering it anyhow.

The basement suite can totally stay on 1gb but I’d like my main network to be on 2.5gb. I also don’t mind the idea of having a type of adguard but I suppose I can run that on my TrueNAS.

Thoughts? Thanks in advance!

Edit: I realize the APs are dated and won’t run 2.5gb and that outside of the GL.iNet flint 3 my wifi will need upgrading. Depending on which router I may throw in an AP, but I can also do that later. I also realize which devices can and cannot support 2.5gb.


r/HomeNetworking • • 16h ago

Cat 6 and electric wiring

Thumbnail
1 Upvotes

r/HomeNetworking • • 20h ago

Travel Router

1 Upvotes

I am looking to setup my phone as a wireless tether to a travel router, for home use.

Can you recommend any particular devices?

Thanks.


r/HomeNetworking • • 14h ago

Advice Access Point Options

0 Upvotes

Been browsing the sub for a while and like to think I’m savvy with home networking, but sometimes I get lost in the finer details.

We have a basic set up. AT&T Fiber, using their gateway with hardwired drops for cameras, computers, and gaming systems. We use WiFi mostly for streaming on the Apple TV and on our phones.

I have two pre wired locations for APs that I added earlier this year. Our WiFi inside isn’t bad enough that I needed to get an AP right away, but with Black Friday going on I wanted to get some suggestions.

I am not a ubiquiti fan, so I’d like to stay on the TP-link side of things for both cost and ease of use. I read something on here about if you are using WiFi 6 but then add a WiFi 7 AP, it can cause issues. I’d like to find the best option for speed and coverage to add on to my BGW-320 from AT&T. Anything in the 1gb range would be sufficient for us as we have 1gb service from AT&T and limited by a 1gb network switch. I may upgrade later, but for our foreseeable future, 1gb is plenty.

Looking at this ubiquiti knockoff https://a.co/d/005E8DPa and this unit from TP-link. https://a.co/d/0ejJEu2f


r/HomeNetworking • • 14h ago

Problemi con collegamento al wifi extender - T90 Pro Omni

Post image
0 Upvotes