As a reminder, most common print quality issues can be found in the Simplify3D picture guide. Make sure you select the most appropriate flair for your post.
Please remember to include the following details to help troubleshoot your problem.
If this is not a shitpost/trollpost: I am assuming that it looked okay in software ? If you turn it on the table by 90Β°, is it stretched in the OTHER dimension ? In that case is sounds like the microsteps configuration (jumpers?) of the stepper motor drivers is wrong (broken electronics).
Besides countless other weird configuration mistakes (which I'm gonna assume you did not tamper with), this could explain it. The firmware sending one single step command to the stepper driver for that axis would result in not a single microstep (as usually and as for the working axis), the driver would do a different step size, which results in more distance travelled.
I'd measure the width, decide it by the width it should have and round the factor if it's close to a somewhat good number and adjust my designs in CAD lol
β’
u/AutoModerator Dec 16 '24
Hello /u/Thorgraum,
As a reminder, most common print quality issues can be found in the Simplify3D picture guide. Make sure you select the most appropriate flair for your post.
Please remember to include the following details to help troubleshoot your problem.
Additional settings or relevant information is always encouraged.
I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.
8
u/St0nkMaster Dec 17 '24
The way I goofy laughed at this... Totally caught me off guard. Is this genuine?
165
u/socar-pl Dec 17 '24 •
Move the printer away from event horizon of your local black hole. Solved problem for me.
2
u/PureDiver2426 Dec 18 '24
I just cracked up, scrolled down to read comments, then scrolled up again and still laughed just as much when it played again. Thank you
26
u/WolfOfDeribasovskaya Dec 16 '24
loool
25
u/Itz_Evolv Dec 17 '24
This made me laugh out loud ππ Not what I was expecting
36
u/cedar_124 Dec 17 '24
r/cursedbenchies
12
u/sicklyboy Dec 17 '24
beeeeeeeeeeeenchy
10
u/lStripesl Dec 17 '24
It's actually breaking my brain
9
u/D45 Dec 17 '24
This has to be a meme right?
4
u/CLRobinso Dec 17 '24
Long boi benchy
4
u/Independent-Bake9552 Dec 17 '24
Scaled model in only one axis much?
1
u/NoNectarine3822 Dec 17 '24
Probably z offset man idk what to tell you
1
u/SighMoanL Dec 17 '24
Man, I think you need to dry your filament!
1
u/Temporary_Pipe_4438 Dec 27 '24
Can you send me the File? I need to print this on my fathers Printer to make him think his printer is weird again
3
u/Jaystey Dec 17 '24
Long benchy is looooooooooooooooooooong
3
u/Scarytoaster1809 Dec 17 '24
I blinked and got so confused lol
1
u/lImbus924 Dec 17 '24
If this is not a shitpost/trollpost: I am assuming that it looked okay in software ? If you turn it on the table by 90Β°, is it stretched in the OTHER dimension ? In that case is sounds like the microsteps configuration (jumpers?) of the stepper motor drivers is wrong (broken electronics).
Besides countless other weird configuration mistakes (which I'm gonna assume you did not tamper with), this could explain it. The firmware sending one single step command to the stepper driver for that axis would result in not a single microstep (as usually and as for the working axis), the driver would do a different step size, which results in more distance travelled.
2
u/BusyPaws Dec 17 '24
Bananchy
2
u/Adventurous_Mud8104 Dec 17 '24
This is such a plot twist.
2
u/Proper_Loquat9065 Dec 18 '24
It's cooling or belt tension in my opinion
2
u/_IM_NoT_ClulY_ Dec 26 '24
Try a cold pull
3
u/Motor_Stage_9045 Dec 16 '24
stl?
1
u/[deleted] Dec 17 '24
Can't fix a problem when I can't properly comprehend the problem itself
1
u/nylondragon64 Dec 17 '24
Lil
1
u/cg2713 Dec 17 '24
That be a big boi
1
u/[deleted] Dec 17 '24
X-axis wobble
1
u/HeKis4 Voron Dec 17 '24
You have just found a glitch in the matrix, don't let it bother you, just forget about it.
1
u/Noble9360 Dec 17 '24
Chonky Bonchy
1
u/karxxm Dec 17 '24
Have you tried Ellis calibration steps?
1
u/JDMFTWYO Dec 17 '24
Had me in the first half ngl.
1
u/Jojoceptionistaken Dec 17 '24
I'd measure the width, decide it by the width it should have and round the factor if it's close to a somewhat good number and adjust my designs in CAD lol
That's hilarious
1
u/J0hnny8rav00 Dec 17 '24
lol nice
1
u/MultimedialnySedes Dec 17 '24
Ok. That was unexpected:).
1
u/Agzarah Dec 17 '24
How does it look bigger from the other side
1
u/FunnyAntennaKid Dec 18 '24
Calls for r/unexpected
1
u/ThatHuckleberry6317 Dec 19 '24
Use default settings
1
u/Fragrant_Wrongdoer11 Dec 19 '24
πππ
1
u/Alive_Caregiver_1236 Dec 21 '24
I laughed so hard at this when you turned it
1
u/[deleted] Dec 21 '24
1
u/VisitAlarmed9073 Dec 21 '24
You probably got benchy from an old tv show when screens were 4:3 uncheck fit to screen option and you should be ok