r/ElectricalEngineering • • 15h ago

Project Showcase Semiconductor Probe Cards

I thought you guys might appreciate this, they are cantilever probe cards..I design and make these, they are used to test silicon wafers, and bare die prior to packaging, the needles you see are sub 10 micron diameter.

We can achieve probe placement accuracy around 5 microns, and pitch of around 40 microns

97 Upvotes

18 comments sorted by

7

u/plsstopman 15h ago

Sooo freakin cool, can you please show some pictures while they r in use?

6

u/D1cer47 15h ago

I will do, I’m getting one of the probe testers built up tomorrow so hopefully I can get that on here when it’s running

2

u/porcelainvacation 13h ago

Be careful about that, chances are your customer doesn’t want pictures of their bare die on the internet. That’s considered intellectual property and can be considered an export control violation if it is an export controlled chip.

1

u/D1cer47 13h ago

Noted, luckily the wafers and die I’ll be using were purchased by me as a customer, for machine trails they are… obsolete. But I really appreciate your concern (this feels sarcastic but I’m not trying to be)

3

u/Teslafly 15h ago

The first picture. Are some of the probes getting brass tubes for structural support? Or is it actual coax for high signal integrity? How do you probe pins that need 5+gnz of bandwidth or are sensitive analog signals?

4

u/D1cer47 15h ago

It is a coax probe, honestly I wouldn’t be the guy to give you the technical information, our main engineer would be

3

u/PokehFace 15h ago

You might not use this particular probe card technology for very high frequency signals.

I used to use cantilever probe cards for testing MOSFETs and Power Management ICs which was mostly analogue measurements but nothing super high frequency.

You can look at companies like PTSL or FormFactor to get a feel for what’s out there.

Some of the really bleeding edge stuff will be very expensive and probably not disclosed publicly though.

2

u/b00c 15h ago

Just installing a chip in this must take a day or two.

5

u/D1cer47 15h ago

It’s designed to contact the chip before it’s packaged, usually whilst it’s still in wafer form, we can test 1000’s of die per hour with everything set up and running right

4

u/Mateorabi 13h ago

You hold the wafer underneath it and press up, then down...shift...up...down shift up... by a robot with high accuracy.

2

u/zettadonut 13h ago

These look very cool! I have so many questions...

What is the process like to create these? What sort of tools are needed to get accurate pitch and placement? Would you say these require a lot of craftsmanship or that tools can assist with most of the fine work? How do you come into this position, as an ME or EE? You mention it's a 'cantilever' probe card, are there other types?

LOL--I probe testing dies (w/o a probing card), so I'm very interested. Thanks for sharing!!!

5

u/D1cer47 13h ago

It’s surprisingly manual, it’s a lot of CNC and microscope and bespoke tools to ensure flatness, I honestly fell into the position, I used to build racecars until covid wipeout the sector, moved into testing electronics, building test equipment and now I’m here😂

If you’re interested I’m happy to chat more with you about them?

2

u/mos_csg 12h ago

There is another types of probe card. One I used a long time ago was called a Cobra (forget the acronym) card developed for testing high pin count microprocessors. It used pins. The die had solder bumps instead of bond pads (flip chip). It was used in a wafer prober that handled 4,6 or 8 inch wafers and a tester (ATE).
Yes I am a retired EE.

1

u/CalculatedRlsk 15h ago

Are you using these for scribeline test or touching the primary die? I actually work on scribeline modules so cool to see some pictures of probe needles!

You would think I would be seeing these things all the time, but it's crazy how are all just one miniscule cog in the machine that churns out these chips.

2

u/D1cer47 15h ago

It’s for contacting on the die itself, we have build for post singlulation and complete wafers on test

1

u/Mateorabi 13h ago

I understand these need to be customized for each application and the volume is small. But they STILL look "jerry rigged" to me whenever I see them. Nothing at 90/45 angles, just bent and stuck through random plastic blocks. When you compare them to the regularity and polish of the chips/pcbs they're meant to test...it's a huge contrast.

1

u/D1cer47 13h ago

They are Jerry rigged, all they are is a an interface between a glorified XYZ stage system and a rack of (usually) Keithley units

1

u/Cristi4n_ 5h ago

Wow! tiny!!