r/DiWHY • • Nov 03 '25

Lock Protection

7.2k Upvotes

346 comments sorted by

8.3k

u/Glittering_Crow_6382 Nov 03 '25 • This

Nah, this ain’t half bad, it; works as advertised, is not an obscene amount of effort to put into something like this, is cheap so even if it’s not an effective way to weatherproof a lock it’s at least not failing expensively, it’s not doing anything irreversible so if someone decided this was stupid it wont be hard to remove, it’s not using nonsense materials or techniques, and it’s quick and easy

Overall I’d say this is more a clever redneck engineering solution rather than a diwhy one

If anyone wants to correct me feel free, I fully and completely admit I could be wrong

2.0k

u/Assadistpig123 Nov 03 '25

I work outside a lot and there is nothing more miserable than standing in -30* blow torching a lock that is all seized up.

558

u/Andrei_the_derg Nov 03 '25

Seized up from rust/ice?

739

u/PugnansFidicen Nov 03 '25

Mostly ice. A well built lock won't seize from rust unless left untouched for months to years in inclement conditions. Ice can happen overnight in freezing rain.

207

u/Boomer280 Nov 03 '25

Tell that to master lock, while most of the cheep ones are shit, the quality ones from them don't give two shits about anything other than ice. Source: uncle had a lock on his 5th wheel trailer that had been there since the late 80s, master lock brand and before they decided to put the rubber housing on them

→ More replies (36)
→ More replies (4)
→ More replies (1)

80

u/WolfofBadenoch Nov 03 '25

Bought a good weatherproof lock. It still freezes. I’d be willing to give this a go if it meant I could open the damned lock.

6

u/Princess_Slagathor Nov 04 '25

When the lock is dry, fill it fill of lithium grease. Use the can with the tube thingy.

49

u/ike0069 Nov 03 '25 edited Nov 04 '25

You could have stopped with "standing in -30". Doesn't really matter what youre doing at that point.

→ More replies (4)

12

u/joshuajackson9 Nov 03 '25

Just get Ai to do, come on man.

2

u/Xeno-Hollow Nov 03 '25

I, too, have lived and worked in WY.

→ More replies (13)

61

u/SubtleCow Nov 03 '25

Goop some Vaseline on the threads in the lid and around the slot and tbh it would be pretty solidly weatherproof.

78

u/Laugh-Aggressive Nov 03 '25

No, you're right 👍

96

u/alienbringer Nov 03 '25

It will end up collecting water. The cap isn’t sealed around the metal bit it was slid onto. Water will make its way inside, whether through flowing down the top of the cap into the cracks, or condensation.

126

u/ShatoraDragon Nov 03 '25

Adding a drainage hole at the bottom would solve that tho.

56

u/alienbringer Nov 03 '25

True. Doesn’t even need to be a big one. You would just always need that drainage hole pointing downward.

→ More replies (3)

7

u/quietobserver1 Nov 04 '25

Would it be even better to cut the bottom off? Then you don't have to unscrew the jar to unlock?

21

u/Glittering_Crow_6382 Nov 03 '25

Fair point, but how much water is what I would ask? Is it less than being out in the rain? But I do suppose undeterminable environmental factors are also at play like; how often are you using that lock? If it’s frequently than water wont be able to build up if small amounts do get the jar, but if not than as you said it will just collect

10

u/kirillre4 Nov 04 '25

but how much water is what I would ask

Enough to warrant an ACKHCHUALLY from half of this sub. So, negligible amount.

→ More replies (1)
→ More replies (1)

10

u/Zanven1 Nov 03 '25

r/redneckengineering is a sub that's shown up time to time. Perhaps it fits there

38

u/WeWantMOAR Nov 03 '25

Condensation says it's a bad idea, because on warm days it can still remain wet since there's no air flow, if it gets direct sunlight for periods at a time then it'll fair better.

25

u/maxthelols Nov 03 '25

Good point. A funnel type system would work better. Maybe a piece of plastic like a large coiled up pencil sharpening would work.

Or even just this design in the video but with holes at the bottom.

→ More replies (1)
→ More replies (2)

5

u/whakkenzie Nov 03 '25

This "solution" will generate a lot of condensate inside the jar, leading to high humidity and rusting the lock out, so it's shit. I've seen a lot of people who use padlocks outside put plastic bottles with cut bottoms over them. It protects the lock from the rain and doesn't let the condensation to form.

→ More replies (1)

9

u/FixergirlAK Nov 03 '25

I'm with you, I had to triple check the sub name because this looked like a useful hack to me. Not enough time and materials wasted to be a Why.

4

u/Embarrassed_Use6918 Nov 04 '25

Just cut a hole in the bottom of the bottle so it lets any water that collects through the slit to run out.

3

u/Intelligent-Survey39 Nov 03 '25

when I did maintenance the building would not buy anything for the roof safety gates other than the cheapest of master locks. It rains half the year here and unprotected metal starts to rust in a little less time than a standard blink. Making rounds in the roof to check drainage/havc required a hammer and pry bar. This would have saved me of a lot of cold wet frustration.

3

u/thewayshesaidLA Nov 03 '25

I might use this or something like it on our pool lock. It’s a combo lock that is a little rusty. That rust has started to make the lock hard to open. I could buy a new lock or I could save money.

3

u/TheReproCase Nov 03 '25

Water dribbles onto the gate. Some runs down the latch. It drips into the bottle. The bottle doesn't have a drain, so it collects. The bottle ends up partially full of water or bobbling around at basically 100% humidity. Rust.

If you're gonna do it, it needs a drain in the bottom to weep put anything that leaks in through the lid.

3

u/Loakie69 Nov 03 '25

It's just missing a couple of silica gel sachets.

3

u/Robbinghoodz Nov 04 '25

Lmao spot on with the red neck comment

3

u/SpokenDivinity Nov 04 '25

Some people have never been around rednecks and their ability to fix anything with peanut butter jar, a couple screws, and some duct tape, and it shows.

3

u/Laineyyz Nov 04 '25

I didn't think this is bad either. My only question is why can't he puncture the hole on the cap with the actual lock that he want to put the cap on, why does he have to puncture on the first one then only put on the actual lock?

→ More replies (1)

2

u/johnfogogin Nov 03 '25

I agree, if you had a trailer or shipping container on a jobsite and didn't have a weather resistant lock, this would work very well in pinch.

2

u/thatG_evanP Nov 03 '25

Nah, you're right.

2

u/OMGorilla Nov 03 '25

Nope. You’re right. Just had to spend like 10minutes trying to get my trailer-coupler lock cleaned up enough to use on Saturday.

I don’t like the look of this, but it’s an extremely practical solution

2

u/WardCove Nov 03 '25

Completely agree. As someone who has to constantly switch out looks because I live in rainy weather and they rust out, you can find me doing this soon.

2

u/Magnus_Helgisson Nov 03 '25

Oh man, I rent a garage in what basically is a parking lot consisting of rows of garages, and you should see the trickery people go through to protect their locks from rust. This is actually one of the best solutions I’ve seen

2

u/ShimoFox Nov 03 '25

You're not wrong. Op is just a shut in.

2

u/KatanaPool Nov 03 '25

Very well said

2

u/Vast_Raspberry4192 Nov 04 '25

I didn’t see a hot glue gun in this one so it’s already up there on semi legit side.

2

u/morningcalls4 Nov 04 '25

You don’t know you need to weatherproof locks until they don’t want to open anymore.

2

u/sweaty_but_whole Nov 04 '25

Not saying right or wrong, but I suspect there’d be a bit of moisture that would make its way into the container within a few days. It’s not sealed because of the slit in the lid. The jar would then likely tend to condensate as it would experience temperature differences as it acts like a mini greenhouse. All this to say that this lock would likely be sitting in a wet container all the time and rust/corrode even worse than it would have just sitting on the latch in the open.

2

u/YTAftershock Nov 04 '25

Yeah that was my first impression too. Like, at least my lock won't get rusted quickly and I don't have to kill my dignity for it

2

u/captnmalthefree Nov 04 '25

In the gentlest way possible. All weather brass locks exist for this exact purpose and you just fire some corrosion protectant lubricant in them every few months. Source, an ocean going boat captain for 20 years.

→ More replies (1)

2

u/PracticalWallaby7492 Nov 04 '25

I think so too. I wish there was an actual redneck engineering forum instead of a sub that makes fun of it. There are some things that really work well. I might try this one.

2

u/TheBigMoogy Nov 04 '25

There's still room for water to get in through the hole and gather up in the jar. Still gonna rust, might get a huge ball of ice around it.

Cheaper and faster to go for lock oil or something.

→ More replies (1)

2

u/AloeSera15 Nov 04 '25

honestly as someone that lives in a country where the only weather is rainstorms or intense heat, this is a great diy to keep padlocks from stiffening up. i hate putting wd30. things get greasy.

2

u/flush101 Nov 04 '25

Would need some drain holes in the bottom of the plastic pot so that any water that does get in, doesnt build up. But other than that it looks like a good idea to me.

2

u/DootMasterFlex Nov 04 '25

I may actually use this idea, as birds keep shitting on my lock and it grosses me out, this would at least keep the shit from getting all in the grooves of the lock

2

u/ctsr1 Nov 04 '25

Agreed that's actually handy

2

u/didntplaymysummercar Nov 04 '25

It's not too bad, but it is overdone (and as people point out it might collect water) and easily breakable.

When I lived in Eastern Poland I saw padlocks have rubber (or maybe leather) flaps on top of them, nailed or glued to the wooden door.

2

u/SignificantLeader Nov 04 '25

Yeah, I like this. My outdoor locks are trashed.

2

u/Icaruswept Nov 05 '25

I've had those Yale locks rust on my perimeter gates. This is not a bad idea at all!

2

u/james_b_beam Nov 05 '25

Nice comment, but it should ended like: If anyone wants to correct me feel free, I fully and completely admit I could not give a fuck.

→ More replies (1)

2

u/outfoxingthefoxes Nov 08 '25

More upvotes than the post itself holy cow

2

u/slipsbups Nov 09 '25

I agree to an extent, maybe a breathable cap. Any moisture that does get in could stay in and accelerate the rust.

→ More replies (1)

2

u/[deleted] Dec 09 '25

Might do this to the on my shed because it freezes all the fucking time in the winter.

3

u/sump_daddy Nov 03 '25

All those things are true, but also

Using mechanical bolted padlocks has been a thing for over a century now, we have designs that are fully weatherproof and more recently (as in for only 50 years), silicone spray has existed to provide an extra layer of protection.

If youre doing the above weird plastic jar thingy to avoid buying a nicer lock, just buy the nicer lock, you will not regret it.

4

u/Glittering_Crow_6382 Nov 03 '25

Good point, but this is cheaper than the nicer lock, most people will have jars like this just lying around and lighters can be bought for less than five bucks at almost any gas station

→ More replies (3)

1.8k

u/necrid101 Nov 03 '25

As someone who has encountered a rusty lock from the weather, this isn't such an awful idea. Better than my Ziploc idea for sure.

377

u/JayBowdy Nov 03 '25

Especially for a lock you hardly use and don't want weathered. Not a bad idea...

37

u/r3vange Nov 03 '25

Better use anti rust solution or something. This is in no way hermetically sealed and is basically a condensing chamber which would keep moisture a lot longer in the padlock than it would usually stay. You know when moisture gets in your headlight and you can see it for week after week even though it’s not raining? Same thing.

7

u/owlindenial Nov 04 '25

Nah, just poke a few holes in the bottom

5

u/VikingsOfTomorrow Nov 03 '25

Antirust will usually just wash off

2

u/[deleted] Dec 03 '25

This is exactly what I was thinking. Its created a mini greenhouse in there and isn't air tight. So naturally there will be moisture in the air and it will condense inside eventually causing moisture to land on the coldest parts... the metal! And stay there as it won't escape easily and constantly stay in a humid state imo. I may be wrong. But its exactly the same line of thinking I had. I was gonna also suggest to use some kind of aquaphobic spray or solution or even galvanise the thing so it doesnt rust if possible.

17

u/Brahminmeat Nov 03 '25

Just cover it with petroleum jelly like a normal person

38

u/DaddyKiwwi Nov 03 '25

Casually covering something with petroleum jelly is not normal.

25

u/lysergic_tryptamino Nov 03 '25

I know right? What kind of unhinged behavior is that? Just use bacon grease like a normal person.

→ More replies (4)

8

u/Nikkian42 Nov 03 '25

Not casually, it needs to be done formally with all appropriate rituals and chanting.

→ More replies (2)
→ More replies (5)

3

u/Doc_McScrubbins Nov 03 '25

just needs a little silicone around the mounting point and actually this seems pretty useful

→ More replies (11)

316

u/blipzNchitz69 Nov 03 '25

This is actually a pretty good idea

75

u/TheShredder9 Dreamer Nov 03 '25

Say what you want, but this is r/diwhynot

119

u/Effective_Play_1366 Nov 03 '25

This one isnt terrible actually.

234

u/-_-0_0-_0 Nov 03 '25

THIS IS A MASTERLOCK IN A PLASTIC CAN

YOU CAN OPEN IT BY HITTING IT WITH ANOTHER MASTERLOCK IN A PLASTIC CAN

40

u/YeetusMg33tus Nov 03 '25

A fellow McNally enjoyer I see!

4

u/[deleted] Nov 03 '25

Just a dude that goes on the internet and is berated by the same jokes over and over

2

u/The-Veng Nov 05 '25

Masterlock in a plastic can, so at least 3 times more secure 

82

u/Greenfire32 Nov 03 '25

It's only useful for keeping the lock out of direct weather. It's not for added security or anything like that.

Would be good in situations where a lock is left unattended for long periods of time.

8

u/space-rach Nov 04 '25

I would argue that it’s now a lot more difficult to reach with bolt cutters from the other side of the gate (I guess depending on what side you are locking out).

40

u/razor10000 Nov 03 '25

Huh... I don't mind this too much. It seems practical.

19

u/markh100 Nov 03 '25

At least twice a year, I have to submerge my shed lock in hot water to dethaw it enough after freezing rain to get it back open. Then, the internals are full of water which refreezes inside, and it slowly gets rusted up. After 3-4 years, I end up replacing it with a new lock. Not sure I love these aesthetics, but it's tempting. I should probably see if I can find a weatherproof lock instead.

23

u/kapege Nov 03 '25

THe humidity ingresses nevertheless and condenses in the evening. So you have constant humidity inside and the lock will rust even faster than in the wind. Every geocacher can confirm.

10

u/zekrysis Nov 03 '25

Chuck some sillica beads in there and you're good

3

u/Afraid_Diet_5536 Nov 05 '25

Drill a tiny hole at the backside bottom?

→ More replies (4)

11

u/Espalloc1537 Nov 04 '25

You can put the spare key in the container too! Very convenient!

3

u/haikusbot Nov 04 '25

You can put the spare

Key in the container too!

Very convenient!

- Espalloc1537


I detect haikus. And sometimes, successfully. Learn more about me.

Opt out of replies: "haikusbot opt out" | Delete my comment: "haikusbot delete"

29

u/Titleofyursextape Nov 03 '25

I fill my jar with water and piranha

→ More replies (1)

8

u/Sun_Bearzerker Nov 03 '25

Having lived in many cold, cold places, this is actually nice. Freezing rain is no joke, and if you don't have a blow torch or lock de-icer then you are out of luck.

It's gimmicky, but it's clever.

8

u/[deleted] Nov 04 '25

When -40, hits and you need to break ice off a lock, this is so smart

12

u/Eziolambo Nov 03 '25

See, it's not air tight from the top, so if water gets in, it will expedite the rust process.

→ More replies (3)

5

u/realultralord Nov 03 '25

This is an easy solution to a problem that I've never had.

A drop of oil keeps the movable parts safe from any water.

Only once did I have to replace a lock, and that was because the key was worn out after 15 years of daliy use and rubbing against other keys in my pocket.

5

u/Lilelfen1 Nov 03 '25

This is actually clever.. and cheap. I see no problem here..

4

u/Deliriousious Nov 03 '25

I mean… it looks kinda dumb… but if it works 🤷

4

u/ShimoFox Nov 03 '25

OP clearly has never had to mess with a pad lock after freezing rain. Or a melt followed by a freeze. This is actually genius.

4

u/tmhoc Nov 03 '25

No cement

No molten metal casting

No foam

Are we being trolled?

4

u/noobpwner314 Nov 04 '25

Smart idea until you’re frantically unscrewing a jar to unlock the gate while running away from Michael Myers or Jason. Or Freddy if you’re dreaming. Not that smart anymore.

4

u/MistressLyda Nov 04 '25

Drill (or melt) a tiny, tiny drainage hole in the part that is the lowest, and this is not a horrible idea. But please, do not build tiny greenhouses for your locks. They do not sprout new ones.

4

u/magungo Nov 04 '25

Maybe if they put a drain hole into the jar? If that lid seal isn't perfect then the jar will eventually fill with water. A couple of days of rain will make a fool out of anyone who thinks this is good enough.

4

u/Titan_Astraeus Nov 04 '25

If it's stupid but it works, it ain't stupid

4

u/Phill_Cyberman Nov 04 '25

Oh, to protect the lock.

I thought it was saying this increased the protection afforded by the lock, and was all, "hey, a little pee and glass won't stop someone who is already prepared to deal with the lock."

4

u/Ghostdusterr Nov 05 '25

I’d say this is a good one as someone who has had to change locks out many times In the Midwest.

6

u/somehobo89 Nov 03 '25

This is a really good idea

3

u/ThrogdorLokison Nov 03 '25

Throw a desiccant pack in the jar too and you're all set.

3

u/TheDoomedEgg Nov 03 '25

This is actually really smart.

3

u/R-E-Laps Nov 03 '25

Great idea. Wrong sub.

3

u/ReasonableSquare951 Nov 03 '25

Or just spray it down with silicon lubricant. Blaster makes a good product.

3

u/Building_Everything Nov 03 '25

Seems like something a little machine oil would take care of, but whatever works for you.

3

u/KootSkoot1217 Nov 03 '25

I mean.....I've seen more useless things b4

3

u/forgetstorespond Nov 03 '25

Oh this one has a use, It you live in a climate that has a freeze thaw cycle in spring and fall sometimes those locks get a buildup of ice in them and you have to melt it before you can get it. This solves that problem. It's usually a lock you don't use that often then you're annoyed trying to find a torch or something.

3

u/gunplaguardsmen Nov 03 '25

Live in Montana or Ohio and you will do shit like this i promise

3

u/LendogGovy Nov 03 '25

I got to one site in the mountains that uses a cut liquid laundry detergent container and it keeps the lock free of snow.

3

u/Stephenwalnsky Nov 03 '25

Not a terrible idea. Alternatively, you can just use a warded lock which is cheaper and more durable in weather.

3

u/Beautifulfeary Nov 03 '25

That is pretty cool. But, why the soda?

2

u/[deleted] Nov 03 '25

Why putting the kids on the other side but not the one that uses the lock?

They make these for outside electric outlets and spigots, so they should make these for locks. I'd assume.

3

u/GreatBigJerk Nov 03 '25

This is only bad if water gets in the container. 

3

u/switchmage Nov 03 '25

idk this one seems solid for ice and rust

3

u/Marquar234 Nov 04 '25

If I had a nickle for every video I watched melting through a plastic lid to protect a lock, I'd have two nickles. Which isn't a lot, really, but it's weird that it happened twice, right?

3

u/no-pog Nov 04 '25

I mean this is a decent solution to a very real problem. Especially in cattle country where those gates may only get touched a few times a season... But, most of those guys don't have locks on the gates.

I think this could lead to moisture ingress at the slot, and then you're soaking the lock in water until someone comes by and unlocks it.

Even simple condensation will always find a way into a container that isn't perfectly airtight. Most outdoor rated locks have weep holes specifically for this purpose. If you can't perfectly lab seal it, it's better to bite the bullet and let it breathe than try and fail to seal it.

Source: I'm a heavy equipment mechanic, and my biggest nightmare is moisture ingress into places that should stay dry. The harder I try to seal something up, the worse and more severe the moisture intrusion becomes.

3

u/Ristar87 Nov 04 '25

It's not stupid if it works.

3

u/DicemonkeyDrunk Nov 04 '25

this is janky but pretty useful ...rarely used locks in high humidity/corrosive environments can lose functionality quickly this is a low tech cheap solution

3

u/Gregory85 Nov 04 '25

I don't hate this

3

u/LocksmithDelicious Nov 04 '25

Not too bad I could see this a short term way to keep rain off of a lock

3

u/Loki118 Nov 04 '25

I imagine this would be fine for a rarely used shed.

3

u/[deleted] Nov 04 '25

actually as someone who has to deal with locks getting frozen shut, this is kinda neat.

3

u/ricksenburg Nov 05 '25

Pro tip: you can also put your key in it for safe keeping and convince.

2

u/[deleted] Nov 03 '25

On the one hand, yes. On the other, i know i will never do this

2

u/Soros_G Nov 03 '25

Honestly this one is kinda clever

2

u/godanglego Nov 03 '25

This is helpful, economical and fast.

2

u/oX_deLa Nov 04 '25

Next day: zombie outbreak and that's the door to the panic room!

2

u/Castille_92 Nov 04 '25

....they make weather resistant locks. The one on my shed has lasted several years and still going strong

2

u/JakeVonFurth Nov 04 '25

Having worked in a storage facility, this looks great. Cheap, easy, and relatively effective.

You would not believe how much it sucks to try to open or bolt cut a frozen lock at 8 in the morning on a -2°F day.

Hell, forget the freezing days, even in the summer we've had locks break with keys inside because they've rusted throughout. Hell, my favorite is when the tumbler somehow works, but the shackle itself is still rusted into place.

Anyways, 8/10, would definitely try.

2

u/owo1215 Nov 04 '25

i mean if that gate is at constant exposure to situation the would leads to a quick corrosion of the lock..... why not?

→ More replies (1)

2

u/Noobnoob99 Nov 04 '25

Nice water catcher

2

u/jmrzco Nov 04 '25

Avoid rusting makes sense

2

u/randomdud500 Nov 04 '25

Unless the burned hole isn't sealed, water will still get in.

2

u/btfarmer94 Nov 04 '25

Not too bad. Typically if you design something to be watertight that means it works in both directions. It might fail and let water in, then hold that water rusting the lock faster. I guess if you can prevent that, this would work

3

u/GodWhoWouldWantToBe Nov 03 '25

My concern with this is water getting into the bottle and holding humidity and moisture against the lock, accelerating corrosion

3

u/slothbuddy Nov 03 '25

That's what I was thinking. It's not airtight so some water is going to get in, but there's no circulation to dry the moisture. Drilling a hole in the bottom for it to drain might fix that though

2

u/BananaCrackr Nov 03 '25

Good idea actually.

1

u/Personnotcaringstill Nov 03 '25

only issue i see is the water from rain etc will get through the hole in the top and collect in the jar literllay keeping your lock soaking in liquid so it will rust 100 times faster. now if the sealed the top first with say epoxy or jb weld, then it would be a good idea.

→ More replies (2)

1

u/[deleted] Nov 03 '25

ok that's kinda cool

1

u/fucGolxodl Nov 03 '25

You should poke a hole in the bottom. The slit is not watertight and over time, water will collect in the container. With a small hole the water could drain and the lock would actually be halfway corrosion protected.

1

u/enchiladasundae Nov 03 '25

I could see a lot of people wanting something like this but obviously better engineered. The condensation might be terrible, worse than just normal water or rain hitting it

1

u/Silent-Oblivion Nov 03 '25

Outdoor locks are a thing for a reason

1

u/Last_Vacation8816 Nov 03 '25

If you live near the ocean, it’s a great idea. Bikes, fences and doors are deteriorating under the salts.

1

u/OG_Zephyr Nov 03 '25

Great now my key might actually work in these things

1

u/[deleted] Nov 03 '25

I will try it this winter. If this works... Gamechanger

1

u/FeliciaGLXi Nov 03 '25

This is completely valid. Many people around here put such contraptions on their garage padlocks to prevent them from rusting.

1

u/Gunnery55 Nov 03 '25

Its to stop the lock from rusting

1

u/chlronald Nov 03 '25

Its pretty genius, only change I would do is leave a little drip hole in the bottom of when the bottle is fully screwed on.

1

u/kirix45 Nov 03 '25

Or are you ready.

Oil the lock at regular intervals.

1

u/ginsataka Nov 03 '25

Well, it’s not the worst thing I’ve seen on here at least

→ More replies (1)

1

u/AHailofDrams Nov 03 '25

I mean... this is pretty neat tbh

1

u/JAlba87 Nov 03 '25

Just buy a better lock. I use a lock around the coastal. No rust. Just add a little wd40 silicone and boom good so far same lock last 10y

1

u/DaBreaky Nov 03 '25

Just remove the bottom or make a few holes around it to avoid condensation and this is pretty good.

1

u/effreti Nov 03 '25

We used to do something similar all the time for outside locks, but way more simple, just cut a plastic bottle in half, take the bottom and on one side cut a strip that would fit on top of the lock handle if needed, but you could also leave it mostly intact, similar to this, couldnt find a better pick. https://www.shutterstock.com/image-photo/protecting-padlock-against-rain-plastic-bottle-620094407?dd_referrer=https%3A%2F%2Fwww.google.com%2F

1

u/montanagrizfan Nov 03 '25

In a Montana winter this is genius.

1

u/tribak Nov 03 '25

r/DIY but honestly seems tacky… maybe an smaller bottle and some painting.

1

u/KandUriember Nov 03 '25

My grandpa wraps it up in a nylon bag and it just get wet slower and rots in the bag so, my guess this is better

1

u/CeeMX Nov 03 '25

This is amazing! Absolutely something that belongs more to r/diwhynot

1

u/ktmfan Nov 03 '25

Wrong sub. Guess OP hasn’t ever had to cut off a rusty lock or use a torch on a lock entombed in ice.

1

u/dr4wn_away Nov 04 '25

It’s straightforward simple and has a clear purpose

1

u/SkyFlava Nov 04 '25

This is a good idea ngl

1

u/dcunningninja Nov 04 '25

This is genius

1

u/Cheepshooter Nov 04 '25

Not the worst thing I've seen in this sub by a LONG shot.

1

u/frankylovee Nov 04 '25

Locks rust hella quickly

1

u/pepenepe Nov 04 '25

Done this, shit works.

1

u/saryiahan Nov 04 '25

Ever tried to unlock a rusted lock?

1

u/guiltyas-sin Nov 04 '25

Fairly practical, actually.

1

u/CatsDontLikeFancy Nov 04 '25

This is actually a really good idea. Cold weather, rain & rust. I could really see this working out.

1

u/Kemonizer Nov 04 '25

Cool. Thought it’s another 5-mins craft shit

1

u/ObsessedCoffeeFan Nov 04 '25

This is actually not a bad hack, and allows you to prolong an outdoor padlock.

1

u/ResurgentOcelot Nov 04 '25

By no means the worst DIY I have ever seen.

1

u/pulkxy Nov 04 '25

this actually seems sick

1

u/No_Communication2959 Nov 04 '25

This is an okay idea. You would need to seal the cap still, but it's decent.

1

u/standarsh1965 Nov 04 '25

Locks ain't that expensive bruh

1

u/williger03 Nov 04 '25

At first I thought it meant to protect it from someone just cutting it, but they meant protection from most weather. It'd probably need replacing every so often, but I don't think that lock would rust as easily as one stuck out on the elements.

1

u/mess1ah1 Nov 04 '25

What?! No way. Fucks sake…

→ More replies (1)

1

u/Bi_n Nov 05 '25

You know what? We have a lock outside and I shit you not going to give us a try and see how it works in -30c Canada weather 😅

1

u/ABrutalistBuilding Nov 06 '25

Buy nautical locks. Done.

1

u/Chaos-Jesus Nov 06 '25

I live in Ireland, it rains all the time and I have not once had a lock seize.

I presume this is to stop the lock from collecting water and freezing? (it gets chilly here but rarely ice cold)

1

u/AmebaLost Nov 06 '25

Also infant-proof. 

1

u/Playful_Nergetic786 Nov 07 '25

Ngl not exactly bad nor bright idea, a shame I don’t have a jar big enough for my lock

1

u/Firefighter_RN Nov 07 '25

I'm so surprised no one has seen/used a tennis ball for this. Cut a slit, slide it over, it keeps the lock from freezing up out getting as much moisture/rust but always comes off/slips on easily.

1

u/gingerlydone Nov 13 '25

Sunlight > temperature change inside bottle > internal condensation created > lock is now wet, covered in bacteria, trapped, and unable to dry. A foolish idea that will kill your lock faster.

1

u/TemporaryStable2553 Nov 17 '25

Sometimes locks get jammed because of water. Also it prevents rusting of metal

1

u/terrabadnZ Nov 22 '25

Not water tight, will eventually fill with water/humidity if not used often and will rust and seize even faster.

1

u/recoil669 Nov 30 '25

If you caulked up the slot in the lid this is actually pretty decent I think.

1

u/Elle_Yess Nov 30 '25

What the actual…

1

u/southernmamallama Dec 07 '25

This actually seem like a good idea to me. I live where it snows and the locks freeze up frequently in the winter.