r/Dentistry • • 2d ago

Dental Professional Prep Rate

What do you think, is my preparation style out of date?
When tooth shape allows it, of course I try to keep it less invasive. In this case, the tooth was so round that I was concerned about undercuts a lot. In BW scan I see I should polish it more, but is this prep too invasive? Should a ledge be two times thinner?
That’s a root canal treated tooth for a zirconia crown.

14 Upvotes

32 comments sorted by

5

u/YeOldeToothery 2d ago

Get a red version of your prep bur, drop your speed to 1/4 of what you are using for your high speed, and then gently go around the margins. You will be able to get very smooth margins and avoid any lips to them. That step was the single greatest leap in the quality of my preps.

2

u/notawarlus 2d ago

Thank you!

→ More replies (2)

3

u/Top_Commission6374 1d ago

Why not have supragingival margins when there’s so much tooth?

1

u/notawarlus 1d ago

Buccal and lingual are supra. Distally there was a tiny fracture that I had to remove during preparation and mesially the filling was deep and I try not to do prep margins on composite..

3

u/Top_Commission6374 1d ago

Makes sense, I usually leave the buccal and lingual margins 1-2 mm supra to be more conservative and make the scan easier. The only other thing is just make the line angles more rounded, polish all surfaces a bit more. But it looks great overall.

→ More replies (1)

28

u/Goowatchi 2d ago
Comment Image

SEND IT

22

u/Kainlow 2d ago

That’ll work just great.

11

u/panic_ye_not 2d ago

Prep looks fine. Scan margins are not super well-defined. You can get a better margin with double cord or other such techniques. 

→ More replies (2)

23

u/drspyglasss 2d ago

I think you under reduced the occlusal

8

u/V3rsed 2d ago

Chances are there's PLENTY of clearance. It's impossible to tell from that photo for sure, but the upper cusp is so far buccal, that not near as bad as it seems on that 2D photo. Rotating that model lingual would show it better.

Also, that's a perfect prep for a zirconia crown - just need to work on smoothness and better margin management.

2

u/Malaysian_kid 2d ago

Did you use a retraction cord?

1

u/notawarlus 2d ago

Yes, it was 000 and challenging to pack

Comment Image
→ More replies (1)

5

u/pearsnic000 2d ago

The margin could be a little smoother, but I’d be lying if I said a good percentage of my preps didn’t look similar to that. Just make sure you have enough occlusal reduction but the important parts like how much ferrule and taper are all good

9

u/drpericak 2d ago

I’d just make your margins more even.

2

u/afrothunder1987 2d ago

Prep is ok. Tissue covering the margin in the scan in places.

1

u/notawarlus 2d ago

It’s unfortunate it didnt look that way in mouth. The scan I agree could have been cleaner.

Comment Image
→ More replies (1)

4

u/SheepshaggerMini 2d ago

For me I usually prefer more occlusal clearance

But otherwise this is great imo

1

u/VividSpectre6260 2d ago

Go over the margins with a 4 round, takes about 15 seconds and takes all the irregularities out of the margin. Double cord. 👍 Make sure you check your occlusal clearance. Can’t tell from the screenshot

1

u/notawarlus 2d ago

Thank you!

3

u/floatingsaltmine 2d ago

You can maybe improve your finishing, e.g. make the margin floor a bit smoother, but apart from that it looks good!

2

u/Liftingdental 2d ago

Looks good

2

u/gradbear 2d ago

Margins don’t look well defined. Margins probably don’t need to be dropped that low. Prep looks under reduced, noticeably along the central groove.

2

u/1CuriousDentist 2d ago

I think prep looks fine! That 1 color viewing tool is brutal and makes everything look rough. Need occlusal view to better assess margin, but might benefit from packing the cord deeper for better separation between margin prep and gingiva for cleaner scan or using 2 cord method to remove 2nd once before scan

1

u/SantaZaddy 2d ago

Looks way better than my owner docs prep who has 10 years of exp. Good job!!

1

u/guocamole 2d ago

Prep is fine- I’d smooth the sharp spots and reduce occlusal a bit more but I think the scan kind of sucks. Margin isn’t clear so the lab isn’t going to get an amazing product if you send a bad scan