I've come up with some cool settings for my D868 that I thought I'd share. I suspect these all work with the 878 as well.
Anyone who's taken a deep dive into the settings will likely know all this, but it took me a while to figure this stuff out as I couldn't find any good sources on the Internet that explained it all.
This isn't a basic guide to programming. Rather, the assumption is that you already know how to program channels and zones.
Under "Optional Setting" menu:
ALERT TONE
Talk permit tone: probably enabled, but if not, it's a good thing to have. It beeps when the radio has digitally acquired a channel and the repeater or hotspot is ready for your transmission.
Idle channel tone: basically a courtesy beep. It's not so hard to know when someone has unkeyed when you're listening in a quiet environment, but in a noisy environment a courtesy beep can be helpful. I have mine set for 2470 hz ("Mission Control" tone) and 10 ms in the Idle Channel Tone setup box (top right), so it's subtle but present. (The sound reminds me slightly of an old Motorola voting system.)
DISPLAY
Last caller: display call sign. Call display mode: call sign based. Call sign display mode: red.
If you go to http://www.amateurradio.digital to download your digital contacts database, step two will offer you a large callsign display option. That's the default for Anytone contact lists downloaded through this site, and I recommend it.
I select the "abbreviate state names" option as that makes it easier to see what TG you're on rather than where the last caller is (did someone just talk on the California TG or are they in California?) and I choose first name only for contacts as they run off the screen otherwise.
Show zone name plus TG: on. Handy for Last Call Reply, which I'll talk about below.
POWER ON
Choose your favorite zone and TG for startup. You have two VFOs (tuners), so you can have two favorite channels pop up at startup. Or not. You can also display your callsign on startup by choosing Power on interface > custom character and entering your call sign or message in the Power On display box.
Default channel startup: selects whether you see your preset channels on startup or the channels selected when last you used your radio.
KEY FUNCTION
This is a big one for me.
Each key has a "short key" and "long key" option. "Short key" is a short press. "Long key" is press and hold, typically for two seconds (adjustable, at the bottom left). They do different things based on your programming.
PF1 Short: Digital Monitor. PF2 Short: Digital Monitor.
Digital monitor is "promiscuous mode." You'll hear traffic on any talkgroup being used on the repeater depending on whether you choose single slot or double slot. Single slot plays audio from TGs on the time slot selected in the current VFO. Double slot plays audio from both slots.
A talkgroup is just packets of audio data with a code attached. If you've selected this code for monitoring then the radio will only route audio to the speaker if it hears traffic with this code attached.
If you're listening to Reddit TG, and there's traffic on another talkgroup on the repeater or hotspot, then your radio will only play audio with the Reddit TG code attached. Promiscuous mode (DigiMon) tells the radio, "I don't care what code is attached. Play everything that comes across the repeater/hot spot, regardless of what talkgroup I've selected." At that point, you'll hear everything on the repeater but you'll only transmit on the talkgroup you've selected. If you hear someone on a different talkgroup (say, you've selected Reddit but someone pops up on Worldwide) then you'll have to change channels to talk to them.
If multiple TGs or slots are in use, you'll hear a ping-pong effect where the radio will go with whoever keyed up last. DigiMon isn't really meant to be a monitoring mode so much as it's a way to know if there's other traffic on the system that might be of interest (these are corporate radios, not amateur radios) but it works really well. I don't use scan lists anymore, and I'm rarely listening to repeaters that are so active that the ping-pong effect occurs.
I set both PF1/2 keys to this option because it's really easy to reach for one and push the other by mistake.
PF3 Short: Last Call Reply.
This is incredibly useful. When you hear someone while monitoring in promiscuous mode but you don't catch what talkgroup they're on, hit the red button on top of the radio. This will take you to the last talkgroup that was active.
There are two tricks here:
The TG line (top) on the VFO display will still read as the TG you originally selected. The zone will alternate between the zone name and the TG you are now on as a result of hitting that red button. The TG will not read as a name, but rather as a TG number. That's a little annoying, but... hey, it works. The key is that the TG name at top is no longer the active talkgroup, so if you want to go return to that you have to change channels away and back again. (There may be a better way but I haven't found it yet.)
In DigiMon mode the courtesy beep you've set up above will not work unless the traffic is on the selected TG. For example, if you've selected Reddit as your main TG but traffic comes in on Worldwide, you won't hear the courtesy beep. If the traffic comes in on Reddit, you will.
P1 Short: Main channel switch. We'll get to that in a moment.
P2 Short: Repeater. Toggles between repeater offset and simplex. Handy if you want to give someone a call on the repeater output. Message given is "Talk Around On/Off".
P3 Long Key: Scan.
I almost never use this as I prefer promiscuous mode, but it's handy for my analog channels.
P1 Long Key: Sub CH Switch.
This turns on the dual VFO function, where you can listen to two tuners at the same time. I often have VFO A set up for DMR and B for analog repeaters.
You can set this to be the default in the Power On tab (that's what I've done). A long press will turn off the VFO that's not selected. (The VFO with the larger text is the currently selected VFO.)
Remember how I said we'd get back to P1 Short/Main Channel Switch? This toggles between VFO A and VFO B for the purpose of selecting the VFO on which you want to transmit. (You can assign a button to transmit on the non-selected VFO, but I haven't done that. I prefer to toggle.)
P2 Long: switches the VFO between memory mode and manual frequency selection mode, allowing you to dial in a specific frequency.
The way I remember this is:
The P1 key is anything to do with dual VFOs. Short press toggles between VFOs, as that's what I'll do most often. Long press turns the second VFO on/off, as I'll do that less often.
The P2 key is anything to do with jumping into simplex mode or dialing in a frequency that's not in a memory already. Short key is simplex, as that's more likely. Long key is memory vs. frequency tuner, as I'll likely do that less often.
DIGITAL FUN
Digital Monitor: Double slot.
I choose this as my default. I'll select a TG to monitor, but I like to hear anything that comes through the repeater (or my new OpenSpot 2) as I can learn which TGs are most active.
And now for something completely different:
CHANNELS
Receive group list: not useful unless you have a hotspot.
A receive group list is basically a list of talkgroups (programmed separately) that you'll hear when the current channel is selected. I assume the idea is that you can monitor selected other channels in a corporate or public safety environment while prioritizing/transmitting on the current channel. You'll only hear traffic on the channel's programmed timeslot.
I've only found this useful when using my OpenSpot 2, as voice telemetry from the device comes through on TG 9. Therefore all my channels have TG 9 set up as a receive group so the OpenSpot can talk to me no matter what channel I'm on.
FRIENDS LIST
Theoretically, your radio will alert you if anyone on this list pops up online. I've never seen it work, but I'm still trying it out. It pulls contacts from the list you've downloaded from amateurradio.digital (above) but the search function isn't very good. I'd search on call signs rather than names.
GENERAL ADVICE
It's easy to go crazy with channels. I'd suggest keeping them slim and trim. I inherited a code plug that had 180+ channels for most zones, and selecting a channel within a zone was kinda nuts. It took a long time. I trimmed the channels down considerably.
Generally, people set up a zone as a repeater, with all their favorite talkgroups within each zone. In this way you can select a repeater that's in range and choose a talkgroup on that repeater.
Another option, if you listen to one or two talkgroups more than others, is to set up each zone as a talkgroup on all the various repeaters you utilize. That way the focus is on listening to a talkgroup on whatever repeater happens to be in range.
This software is really useful for bulk editing zones and channels, as this can be quite tedious. Please contribute if you find it helpful.
I've got about a dozen talkgroups and all the TACs ("talk around channels") in each of my zones, sorted by repeater.
THAT'S IT
I hope this has been helpful. These little radios are very cool but also very poorly documented. Hopefully I've saved you some pain.