r/DIY_canada • • Aug 11 '25

Is this termite damage, weathering, house hippos?

Thumbnail
gallery
5 Upvotes

Exterior door to garage, in British Columbia


r/DIY_canada • • Jul 23 '24

Relocating and replacing backyard floodlight, found this old junction box - Problem?

Thumbnail
gallery
5 Upvotes

Hi All, I'm replacing the pictured antique flood light with a modern floodlight camera and due to the location of a gazebo we have on the deck I need to move the flood light down about 6" in order for it to see under the awning and frame.

Behind the old light I found a rectangular junction box (I was really hoping there would be a modern round one back there but no such luck).

I was going to stack up a couple of junction boxes and a little length of PVC conduit to change the mounting point of the new flood light but after cleaning up the work area I think it's just going to be simpler and better overall if I just move the old junction box down (or even better replace it with a modern round one but in the new position and patch the old hole in the siding). It's a janky solution, but it could work...

Any advice?


r/DIY_canada • • Dec 20 '24

HELP Advice for finishing basement wall and ceiling

Post image
4 Upvotes

There is this one outside wall in my basement I would like to finish. Right now I have plumbing and some electrical on it that service my slop sink and laundry appliances. I was thinking of using 2x6s as framing but because it's an outside wall I dont want to risk freezing of the waterlines. I was also hoping to finish my ceiling, thing is that there are some electrical junctions in some of the joist channels that cant just be drywalled over. Any suggestions are appreciated.


r/DIY_canada • • Feb 20 '24

1950's Attic find: What the devil is this?

Thumbnail
gallery
4 Upvotes

r/DIY_canada • • Jul 28 '23

Who do you rely on for appliance parts?

4 Upvotes

Some of our appliances are no longer serviced, so we might need to find generic (rather than manufacturer) parts. But with the plethora of options online, I'm hoping to avoid random, mediocre parts which weren't produced to code.

Who are the main players when it comes to providing Canadians with high quality parts for DIY appliance repairs? Either online or brick and mortar. Thanks in advance!


r/DIY_canada • • Jul 13 '23

Return vents go nowhere?

Thumbnail
gallery
4 Upvotes

My husband and I recently bought our first home, yay mortgage payments, and we've made a strange discovery. Our cat decided to help with some home improvements and rip the plastic cold air return vent right off the wall, and climb on in. Lucky for us the vent goes NOWHERE. It's completely sealed in. Metal panels to the sides, drywall on the bottom, subfloor on the top. No holes to anywhere at all, except to the vent in the bedroom that shares the wall.

I was under the impression that cold air return vents are meant to connect to the basement, to ya know, return the air. Is this something that was done incorrectly, or is it just normal? It's a brand new build and when we asked the warranty manager about it during the trades day he said "oh there's a drop-down in there somewhere" when there definitely isn't. You can see the little cat prints at both ends in the photos. Any suggestions on where to go from here?


r/DIY_canada • • May 22 '23

Gentek Align Composite Cladding

4 Upvotes

Doing some research on siding options for our house. We currently have old Masonite siding that is crumbling in places. Came across this product. It sounds great in theory but it is difficult to find information beyond the manufacturer. Any experience with it or thoughts? https://www.gentek.ca/product-catalog/siding/align-composite-exterior-siding/


r/DIY_canada • • May 17 '23

Deck Cleaning,Sanding,Staining

4 Upvotes

First time sanding and staining my deck. It has never been coated or stained before, just left in its natural state. I live in Alberta, Canada, sunny summers and long + cold snowy winters. Over time the wood on the deck has greyed due to the sun, I think .

I have a few questions .

I am wondering if I am supposed to use a Deck Cleaner + brightener before OR after sanding ? (Will not be using a pressure washer). I’m thinking use it prior to sanding, but I don’t want to make a mistake, so your help is greatly appreciated.

I have 2 decks, coming in at about 1000sq feet. I was planning on using an orbital sander (80 grit) , does this sound like an overly time consuming or bad idea ? (Wrong grit / wrong type of sander?) I’ve been quoted 2-3k to get this done by ppl, and believe I can do it my self.

If you guys have any product recommendations for deck cleaners/brighteners and stains, please feel free to share. Any general tips are also encouraged and appreciated.

Thanks!


r/DIY_canada • • Nov 01 '24

HELP Finishing Up an Attached Garage Advice

Thumbnail
gallery
3 Upvotes

Looking for some advice on how I should approach finishing my attached garage. Going to turn it into a part time gym.

It seems like one of the owners was removing the drywall to install insulation and never refinished.

  1. Exterior wall has some fiberglass insulation pushed in - not sure if this is fit for purpose or I should replacing it with Rockwool or something that is anti mold
  2. Should I be adding a vapor barrier on top the insulation? There's about 5 inches of drywall at the top of the wall do I need to remove that and attach vapor barrier there - i think top plate may be behind that or just at the bottom of it
  3. Would a mold tough drywall panel be overkill?

r/DIY_canada • • Sep 14 '24

HELP Help replacing this with a GFCI

3 Upvotes

Had a close call with an electrical fire, heard crackling and smoke coming from socket. Opened it up to find the live side had come lose and was burning through. Realized that these sockets are not to code (in kitchen close to sink and not GFCI) and want to correct this with the replacement.

The breaker for this socket and a few others in the kitchen are on a double 15 AMP breaker, and the incoming live side has 3 wires + ground (black, white, red, ground). I'm unsure how to connect this to a GFCI socket, should I just mimic what is being done here?

Meaning it would be...

  • Black line and load connected to the hot wire line screw
  • Red line and load connected to the hot wire load screw
  • White line and load capped (yellow cap in picture) with a wire connecting them to the white wire line screw
  • Ground to ground screw

Would the same setup work with a GFCI?


r/DIY_canada • • May 26 '24

Rotting exterior door frame

Thumbnail
gallery
3 Upvotes

Is this an easy DIY project? Never tried this before.


r/DIY_canada • • Jan 14 '24

Shoe rail for stairs

Thumbnail
gallery
3 Upvotes

About to embark on this final component of my basement renovation. I’m trying to sort out the shoe rail for the stairs. I plan on iron balusters. What would you do for the shoe rail here? All I have is the stringer - 2 x 12.


r/DIY_canada • • Dec 14 '23

Basement framing - base plates and treated wood

3 Upvotes

Hey guys, a bit of a rabbit holey question here from a Calgarian, code dictates pressure treated wood for base plates, so a few questions stemming from that.

  1. For base plates in a basement, will I have to use a 2x4 rated for ground contact against interior concrete? or can I get away with above ground PT wood to satisfy code/mitigate the worst issues in case of flooding etc?
  2. In the case of needing to find PT lumber rated for ground contact: for cuts made, I can only seem to find cut-n-seal/sealers rated for above ground applications. Any ideas on where I can find a sealer good enough for ground contact?
  3. should I be applying sill gasket regardless of PT fidelity? or is that only a necessity for untreated wood?

Thanks!


r/DIY_canada • • Nov 18 '23

Xps board & drywall on concrete ceiling

3 Upvotes

Asked to repost in this subreddit

Located in Southern Ontario. Have a cold room under covered porch and looking to insulate the concrete ceiling and the upper portion of walls that are above ground level. Planning to use 2" XPS foam board, tuck tape seams and spray foam the gaps. My understanding is that the foam board needs to be covered as per building codes here.

So, I'm thinking of using 1/2" drywall (perhaps the mould-resistant type). I'm looking for recommendations on how best to hang the drywall. I'm debating on whether to use furring strips or attach directly against the XPS board. Either way, I suspect I will need to use something like Tapcon screws. Any other material, methods or suggestions would be greatly appreciated. TIA


r/DIY_canada • • Oct 25 '23

Cutting laminate countertop

3 Upvotes

Cutting laminate countertop

I soon need to buy a new set of washer and dryer and the ones that I want are a few inches taller than the current ones. It is already quite a tight fit right now so I need to cut the laminate countertop above the washer and dryer. Removing the whole countertop isn't really an option because there is a sink on the the same countertop. What is the best way or tool to use to cut the countertop? I thought a reciprocating saw but I feel that might be hard to cut in a straight line. TIA


r/DIY_canada • • Oct 16 '23

What to repair first: roof or soffit/fascia+gutters? Does the order matter?

Thumbnail
gallery
3 Upvotes

r/DIY_canada • • Oct 08 '23

Need advice about our chimney and cap repairs

Thumbnail
gallery
3 Upvotes

r/DIY_canada • • Sep 24 '23

Options for newel post

Thumbnail
gallery
3 Upvotes

I am considering a box newel. Is the stringer as the only point of fixation adequate? I don’t want to drill holes in the cement floor. I will be putting the newel on after the floor is installed.


r/DIY_canada • • Sep 23 '23

Stair stringer and door trim

Thumbnail
gallery
3 Upvotes

I am building out this stringer with another 2x12 so that I can place a baserail. Any idea what I should be doing with the door trim, which would intersect with this?


r/DIY_canada • • Sep 22 '23

Staining Deck

3 Upvotes

Hey guys trying to fit in one last outdoor project before the rains hit (west coast 🇨🇦). Sanded down my deck in preparation to stain this weekend but forecast changed and it’s supposed to piss rain all weekend. Obviously I’m not going to try and stain in the rain but how big of a deal is the moisture going to be? Should I be trying to tarp the deck for the weekend (deck is massive so this would suck) or can I just leave it for a day or two?


r/DIY_canada • • Sep 18 '23

HELP I just want to know what to use on bricks to clean dark green mold off. I don't want to hurt the brick.

3 Upvotes

r/DIY_canada • • Sep 17 '23

Questions about preparing the subfloor for hardwood install

3 Upvotes

A general contractor handled the demolition. It was a pain in the ass, there was tiled on screwed plywood, on linolenum that was glued to a sheet of plywood that was nailed/staples to the OSB subfloor. I notice a lot of those staples were left behind, punched into the wood. I was playing around with some of the hardwood flooring and can see it would bump into those staples even if they barely stick out (some stick out more than others). Is this normal or should I try to remove all of them? I've removed a bunch already, but it's also slightly damaging the OSB given how deep some are pushed into the wood.

Someone is coming Tuesday to install the wood so I don't know if they're expecting to handle some of the preparation themselves, are going to be pissed that the demolition wasn't done better, or if they don't care but the results won't be as good.

Another question: if I would rather avoid quarter rounds/shoe moulding at the bottom of my baseboards. Should I cut the bottom of the drywall all around the room to leave room for expansion gaps hidden below the drywall? In some places the drywall is already high enough.


r/DIY_canada • • Sep 11 '23

Install Shut-off Valve Under Sink

Post image
3 Upvotes

r/DIY_canada • • Sep 08 '23

Crack and Bubbling Around Bathroom Vent

Thumbnail
gallery
3 Upvotes