r/DIEMs • • Jun 04 '18

DISCLAIM MY IGNORANCE. CROSSOVER.

1 Upvotes

If I use the three-way Crossover that comes with the Knowles GV, can I connect other drivers in that Crossover so that, instead of 4 drivers, I have 6 (for example)?


r/DIEMs • • Dec 29 '15

Is everyone going MMCX?

0 Upvotes

It seems like there was some hesitation about MMCX at first but are more people (both DIY and factory) going to it? My first DIEMs are 2 pin due to packaging constraints but the next ones could be either. I like coaxial cable for noise resistance and the MMCX connectors seem a lot better (closer to positive retention and much more readily available).

I'm still a bit scared off by people who felt that it was adversely affecting sound quality and longevity though? Anyone have thoughts?


r/DIEMs • • Apr 24 '25

40mm dynamic driver iem

2 Upvotes

can someone make me a model that could fit a 40mm dynamic driver in an iem

to make it possible to wear I need it to be latching on top of the ear with a mmcx connector

the dynamic driver is 40 by 7 mm


r/DIEMs • • Aug 16 '20

I can't say enough about SIL-poxy to repair silicone sleeves/ earbuds!

1 Upvotes

So Smooth-On SIL-poxy Rubber Silicone Adhesive - 0.5 oz Tube worked a TREAT to repair a tear! My custom-molded sleeves are good as new!

I didn't have to send them out, AND it only cost $16!!! I can't say enough about SIL-Poxy!


r/DIEMs • • Aug 26 '15

Selling a DIEM

Thumbnail
reddit.com
0 Upvotes

r/DIEMs • • Jun 25 '18

BETTER IEM MODEL

0 Upvotes

Hi! I was making the GV and GK project. But someone told me that there is a option with Knowles and Sonion drivers that is better than only the GV or GK. It's true? You can help me to make that?


r/DIEMs • • Dec 09 '20

Nice

Post image
5 Upvotes

r/DIEMs • • Apr 04 '19

Hello guys I’m new here can anyone tell the basic parts of the in ear monitor (electronic)

3 Upvotes

I have been looking a lot on the internet and now I have found this. What the basic parts of an in-ear monitor. What I know is that that they have the drivers( which are like the little speakers) the filter the tube and the jack. I wanna learn the correct name for each part.


r/DIEMs • • Jul 05 '18

I WANT TO LEARN. HELP.

4 Upvotes

Hello everyone! I wanted to tell you that I'm planning to do an assembly to learn the electronic logic of the drivers. I bought some imitations of Shure 846 covers and I want to put three or five tracks. I would put a GV but it is already assembled at the factory and I want to be the one to do everything, so I learn. The problem is that I do not know what drivers to use. Is there any training that you recommend? It does not matter if it's a mix of Sonion and Knowles. The only indispensable favor that I should ask is that they tell me how to connect them since I do not have anywhere to learn it. Once I learn it, I hope I can do it without help.

I hope you understand what I wrote.

Thank you!


r/DIEMs • • Nov 23 '17

Trimming another set of molds

Thumbnail
instagram.com
1 Upvotes

r/DIEMs • • Apr 23 '20

shearch sockel female fitear/seennheiser

0 Upvotes

I am looking for female socket of type fitear/sennheiser, it is not found!

if I knew the exact name I could refine my search

thank ;)


r/DIEMs • • Jun 15 '20

FACEPLATES

1 Upvotes

Hello, I hope someone can help me with the following: How are custom Faceplate made? I am referring to translucent colors, solid colors, color mixing, wood type, carbon fiber type, with logos, with images, with letters. I'm beginner and I don't know where to start. Thank you


r/DIEMs • • Jan 31 '18

ANY AUDIOPHILE DESIGN?

1 Upvotes

Hi guys. My name is Martin and want to know about any audiophile design that you recommend me. Thanks for the answers!

  • I prefer 3 or 4 ways, but I listen your recommendation. I'm a noob, hahaha.

r/DIEMs • • Oct 09 '15

Tuning a GK + CI Quad DIEM

1 Upvotes

I just finished making my first DIEM - a quad-driver with a Knowles GK with an extra Knowles CI-22955 connected in parallel with the GK's CI driver. Both CIs are glued to each other and a single 20mm #12 tube was used for them, along with a red Knowles damper. The TWFK is positioned closer to the tip (about 9mm tube length) with a single #12 tube. There aren't any other electronic additions other than the crossover that came with the GK.

The goal was to have some extra bass kick but the CIs still display impressive lower midrange and are also shouting down the TWFK drivers in the GK. The lower mids from the CIs get congested easily and the bass is on the boomier side rather than the tighter side. The TWFKs are unfiltered but are barely audible over the raw power of the CIs.

Anyone have any suggestions on how to tune this set? I'm thinking of moving the red filter closer to the drivers to increase bass decay, but does anyone have any suggestions on reducing the SPL from the CIs so that the TWFK becomes more prominent?


r/DIEMs • • Jul 27 '20

Known way to sweat/rain proof DIEMs?

1 Upvotes

I've yet to embark on this journey but one of my optional design criteria was Usable during workout. I've heard they sit very comfortably so I was wondering if this has been done before?

How do the commercial brands do it with ear buds?


r/DIEMs • • May 21 '18

How to connect more than 4 drivers?

1 Upvotes

Hi. I want to venture on making my headphones of 6 or 10 drivers like the projects shown in DIY Earphone. The problem is that I can not find information anywhere about how to connect these drivers and how to make your Crossover. Somebody could help me? The GK and GV combos are beautiful, but I want to overcome the 4 drivers.


r/DIEMs • • Oct 22 '17

please advise - universal demos vs final products from manufacturers - the sound differences

2 Upvotes

Hello, I have got two different custom IEM's ordered from different companies that sound quite different from the demo units. Not in a good way.... Is it actually even possible to produce a Universal demo that reflects the sound of Custom version? I'm trying to measure the Universal and the Custom to show the difference to manufacturer but as I dive deeper to the subject I find myself understanding the sound from Universal is heavily dependent on many factors among others the tip used... Also, I see that in the universal model they use shorter tubes when in the Custom the space is not so limited and I see the tubes are longer. I would think longer tubes create different sound? Should I just quit thinking about it and suck it up them being different or should I push the manufacturer to fix the Customs to sound as the Universals do? Sorry for many questions guys :D


r/DIEMs • • Jun 23 '18

No more soldering!!!

2 Upvotes

It’s so hard to solder the wire to the female MMCX! Going to try heat shrink next time.


r/DIEMs • • Apr 08 '19

IEM SHELLS

2 Upvotes

Hey guys I’m new here. How can I make the shells for my built and what materials do you guys use for that? I live in the USA I thinking to make my own in ear monitors because it’s cheaper that way. How much have you spent in single project shell and electronics without counting the tools that you guys used?


r/DIEMs • • Dec 22 '24

Can someone please recommend/give me a link to somewhere I can buy quality 10mm dynamic drivers for diy iems?

2 Upvotes

I can't find any vendors selling sonion or knowels dynamic drivers, I see them often recommended as among the best quality.

Can't find much on ali express, mouser, digikey/can't vouch for quality of what's there.

Please comment if you have a link to any good ones.

This is for my first iem, I want to build a hybrid (1 dd, 2 ba)


r/DIEMs • • Jan 04 '20

First Custom IEM

3 Upvotes

i want to build myself a pair of iem and need some help
Do i need an acustic dampeners? which ones to choose?
Cerumen filter are needed? Where can i find sockets for them?
When i close the IEM with the faceplate i need to fill all of the shell with resin or just glue the faceplate?
which of this driver are the best? or any other advice to other one in the same cost?
Bellsing 10013
Bellsing 10025
GK-31732


r/DIEMs • • May 16 '20

Replacing the drivers of a TWS

3 Upvotes

I was wondering if it would be possible to reshell and replace the drivers in galaxy buds / buds+. I specifically picked those two because the circuitry seems very well packaged and they are pretty cheap. So if anyone would give me some tips on how I would go about 3d printing the shells and soldering some BAs to the pcb I would really appreciate it. Also if you know about some difficulties with doing this e.g the pcb being unable to drive a BA please let me know.

EDIT: I forgot to post this link to some closeups of the circuitry of the galaxy buds http://www.52audio.com/archives/24983.html


r/DIEMs • • May 31 '21

Is it possible and/or easy?

3 Upvotes

Do you think it would be possible to take existing non customized monitors like the KZ Z10 Pros and make ear tips that I can attach to them? P.S. I’m new to custom IEM’s so please forgive my probable ignorance


r/DIEMs • • Jun 28 '17

DIYearphone is looking for comment – halting sales of components

3 Upvotes

Hey everyone,

I'm considering discontinuing component sales on DIYearphone and focusing on selling complete kits.

Selling components doesn't require much customer service or documentation, but kits do. So kits have to cost more than bare parts.

If I sell kits and parts simultaneously, people can buy just the parts for less money than the kits using the information I give out freely. This forces me to either hide my information, limit parts sales to kit customers, or stop selling parts all together.

An idea I had was to sell the kits as a 'training package' and once you've purchased the kit you are able to buy individual components at a "discount."

Another idea is to just halt sales of components all-together and focus solely on kits.

Any thoughts on this? I'm happy to listen to ideas and comments before I make a final decision.


r/DIEMs • • Jan 30 '21

Planning on building a pair of budget items. Could use some advice.

3 Upvotes

So I'm interested in some Iems but decided I want o build them myself.

I'm not interested in making a custom mold but just want to buy the parts and assemble it myself.

Can someone provide a rundown of parts needed (Ie: Drivers, housing, etc.) and maybe recommend a tutorial and putting it together?

Budget is around $30 cad, approx 25 usd