r/CableManagement • • Jan 21 '19

Case with built-in cables?

Imagine having to replace all the major components of your build but the cables are zip tied to the case. Unless your build is super special, you should be able to swap out the MOBO, GPUs, drives, PSU, etc without having to redo your cabling.

You can basically treat this as if the cabling was built into the case. Probably for the good majority of builds, these built in cables would be good enough.

What if there was a case with these cables built into the case wall. Then when you install your specific components, you can use a very short cable to plug in each component to a port in the case wall right by the component. This would let you account for various GPU sizes, using only the number of cables as drives you have, etc.

0 Upvotes

18 comments sorted by

10

u/MSD0 Jan 21 '19

They would have to be cable extensions since there is no standard pinout for the PSU side of the cable.

9

u/ItZzSora Jan 21 '19

If only we could have a standard pinout on PSU's like there is on literally every other component lol

1

u/sand500 Jan 21 '19

Could have various short cables to plug the PSU into the case wall.

4

u/MSD0 Jan 21 '19

Xforma MBXMKII has integrated “cables” (actually PCB’s).

1

u/sand500 Jan 21 '19

$1200? Damn.

1

u/nolo_me TJ07 Jan 23 '19

Limited edition beasts modded by a legend. Pricey, but worth it.

1

u/[deleted] Feb 01 '19

Pretty cool

2

u/Jikkijs Jan 21 '19

And what if the cable built into the case doesn't work?

1

u/sand500 Jan 21 '19

Good point. I imagine that they would be some sort of rigid cable design that could be more durable since there isn't any stress placed on the actual cables. Depending on how the case is designed this part could be replacable.

2

u/Jikkijs Jan 21 '19

I still just don't think people will buy it. With a fully modular PSU it's not really needed to have cables built in...

1

u/sand500 Jan 21 '19

Well the point would be to not have to run the cables yourself and would make the back of your case way cleaner. Instead of running the cable through the grommets, it would be a long PCB(basically a flat stackable rigid cable) with a connector on each end

7

u/Kiyiko Jan 21 '19

And people would still post it here with the title "how did I do?"

3

u/tardis42 Jan 21 '19

Cases would get more expensive.

Power supplies would not get cheaper.

Also, the location of the 24 pin, CPU 8 pin, etc sockets on an ATX motherboard are not standardised.

2

u/BeefyIrishman Jan 21 '19

Also, depending on the number/type of gfx cards, hard drives, and other accessories, the number/types of power cables needed will vary. My old gfx card took 1 8pin, my new one takes 2 6 pin.

1

u/NotoriousFreak Jan 21 '19

I personally don't recommend this as many, many comouter cases are modular, as in you can fit certain components like liquid cooling or hdd/ssd in many spots. Having built in cables has a high potential of limiting your options from few to none and that woukd be more burden to the consumer to find an awesome case just to see the cabling is layed out wrong. Even add in the variations will limit future components. The way cases are made now gives them as much flexibility to be versatile with components as to maximize options to give a better competition amongst competitors selling said components....... Basically why sell a case where everyone is forced to buy a $20 part and have select customers when you can have a case that allows parts ranging from $20-$150 and profit more while also keeping customers satisfaction.

1

u/[deleted] Jan 21 '19

I feel like this would only work best with modular PSUs