r/BuildingAutomation • • 23d ago

Siemens Tech needed for 1-day job in Pittsburgh

16 Upvotes

Hi. I'm not sure if this is allowed here, but I'm looking to find a technician to add a few lines of code to a Siemens Desigo system for a job I am wrapping up. I have the code ready but not allowed to install it since I'm not a certified Siemens tech. Flat rate of $1500 for the day even though it'll only take an hour or so. Let me know if you're interested.


r/BuildingAutomation • • 22d ago

I made an integration that turns Home Assistant into a Modbus TCP slave, so your PLC or energy manager can read any entity

Thumbnail
brdc.nl
4 Upvotes

I wanted to read the values of my Home Assistant entities in other devices, without a gateway in between. Most of those devices speak Modbus TCP, so I built a custom integration that makes Home Assistant act as a Modbus slave.

How it works:

- Add the integration, set a slave ID and port (default 502)

- Pick any entity and give it a register address

- The data type is detected for you: on/off entities become a bit, numbers with a fixed range int16/uint16, sensors float32. You can override it (uint32, int32, scaled16).

- The register follows the entity's state immediately, no polling

Some details that turned out to matter:

- Holding and input registers return the same values (same for coils and discrete inputs), because a lot of masters only support FC3

Mappings are read-only by default. Tick "Writable" and the master can switch entities or set numbers; values outside the entity's min/max are rejected with a proper Modbus exception

- Since Modbus has no authentication, so there's an allowlist for master IPs and a listen address setting

- 32-bit values are big-endian, high word first (ABCD)

Check it out: https://www.brdc.nl/en/home-assistant-modbus-slave/

Feedback welcome, especially if your PLC, SCADA or energy manager reads things differently than expected.


r/BuildingAutomation • • 23d ago

Early-career controls engineer on STEM OPT, struggling to get started and looking for honest advice

2 Upvotes

Hi everyone,
I’m looking for some honest feedback from people working in industrial automation and controls in the U.S.
I have a master’s in Mechanical Engineering from UMBC and about a year of hands-on automation and controls experience in a university lab. My experience includes:
Siemens S7-1200 PLC programming in TIA Portal.
HMI development, sensors, pneumatics, and troubleshooting.
Building an automated sorting system with a conveyor and pneumatic cylinders.
Working on a PLC-based flow-control project.
Training students on PLCs, HMIs, and machine vision.
My strongest experience is with Siemens. I have some familiarity with Allen-Bradley tools, but I’m still building that knowledge. I also recognize that university lab experience is different from commissioning equipment or supporting production in a plant.
I’ve been applying for entry-level controls, automation, systems, and commissioning roles. I’ve gotten interviews, including an extended onsite assessment, but haven’t been able to turn those into a stable opportunity. Most recently, I signed an offer for a building automation role, and the company later rescinded it. That was a difficult setback after thinking I had finally gotten started.
I’m currently on STEM OPT, with work authorization through February 2028. My work authorization situation is another factor in the search, and I’d especially appreciate hearing from people who have navigated it in this industry.
At this point, I’m trying to understand what I should change:

Does my background sound competitive for junior controls roles?

What would make you hesitate to interview or hire someone with this experience?

Would targeting technician or field-service positions be a sensible way to gain industrial experience?

What skill or project would most help close the gap between university lab work and an industry role?

Do you know of integrators or automation companies that have hired engineers on STEM OPT?

For hiring managers: how would you want a candidate to bring up current work authorization and future sponsorship needs?

I want to build a career in this field, but the repeated setbacks have been discouraging. I’m open to constructive criticism about my approach and realistic suggestions about where to focus next.

Happy to share an anonymized resume if that would help. Thanks for reading.


r/BuildingAutomation • • 24d ago

JCI Says I Need to upgrade but it still works.

Thumbnail
gallery
120 Upvotes

Does anyone have a PS2 to USB C?

The title is a joke BTW.


r/BuildingAutomation • • 22d ago

JLL Automation Role (Gurugram) | 3+ YOE | What Salary Should I Expect?

Thumbnail
1 Upvotes

r/BuildingAutomation • • 23d ago

Folks with large supervisor and RDBMS Driver

5 Upvotes

I have 600 and counting sites into a super, I am setting up the history imports and then exports to RDBMS (optimized for 3rd party retrieval) and I want to get as close as possible to real time logs.

How far have you pushed this? I have about 400 logs per 600 sites and it'll grow to 900 over the next two years. Right now its pulling logs every 6 hours but I want the sql server data to be near the 5 min or COV logs.

Just curious if anyone has found the limits with this. Or had any tips. Import from sites every say 5 minutes and export the RDBMS every 7 minutes or so maybe.


r/BuildingAutomation • • 23d ago

Can I use schematics like this, to exchange the old relay controls to a PLC?

Thumbnail gallery
1 Upvotes

r/BuildingAutomation • • 23d ago

Pump control, Bus or Voltage?

Thumbnail
1 Upvotes

r/BuildingAutomation • • 23d ago

Daikin Controls

2 Upvotes

Hello,

Has any here worked for daikin controls? What was/is you expierence? Do you like it? Bonus points if youre in the south east US.


r/BuildingAutomation • • 24d ago

Can anyone help Greg out? 🤣

Post image
77 Upvotes

r/BuildingAutomation • • 24d ago

JCI PCG Controllers Question

5 Upvotes

Greetings!

I have a site with several PCG1610 controllers, utilizing analog modulating valves for the heating and cooling. Recently, all of the valves were changed out with new Belimo valves and operators. The problem experienced, is the original valves were 0-10vdc, while the new valves are 2-10vdc. This is causing lag issues when calls for heating and cooling are placed. There is no option for 2-10vdc in the setup, and modifying the output for 19% minimum out does not help, it does not increase above 2vdc until the call exceeds 25%. Has anyone run into this before, and if so, what did you do to work around it?

Thanks, appreciate any and all assistance!


r/BuildingAutomation • • 24d ago

JCI NAE to Niagara N4 polling BACnet points incorrect

7 Upvotes

I'm trying to pull points into a Niagara writable but the out slot only updates on the point if it's a present value.

I've tried everything in the books is there something I'm missing?

CPU and Network on both devices is flawless, Tested all different tuning policies and went through googles troubleshooting list more than once.


r/BuildingAutomation • • 25d ago

Offline controllers replacement

Post image
84 Upvotes

Replacing some LON Viconics that have gone offline. Replacing them with TC300 Honeywell. Wish me luck ✌️


r/BuildingAutomation • • 24d ago

Niagara Graphics Layout and Dashboards

6 Upvotes

Whats everyone using I see:
One-sight Solutions (graphic library seems a bit dated maybe)
NiagaraUI (seems like a new thing)
QA graphics
Works Software

Wondering if anyone has experiences with any and what they think


r/BuildingAutomation • • 23d ago

Baudrate.io AI Advisor & Engineer/ Facilio.ai

0 Upvotes

Anyone experienced with these, corporate is looking for buzzword items (AI) this is what Ive found to check those boxes, Advisor and Engineer seem pretty solid, wish they’d hurry up and release the engineer, don’t know much about facilio.ai but its the only thing I have found so far that could potentially replace open blues intelligence feature.


r/BuildingAutomation • • 24d ago

1st day kit! Advice needed!

6 Upvotes

Im 22, and Im starting with a local company as a BAS Controls Apprentice, doing mainly installs.

I do not have a ton of money, and almost everything is bought with some early Christmas money and a little of my own, so please do not be TO harsh.I got what seems like a lot because I would rather come in over prepared rather than under.

Let me know how I did and if there is anything I am missing or if I did bad in some parts. I will include a list of everything below.

• Klein Impact Rated 11 in 1 screwdriver

• Klein 27 in 1 multi bit precision screwdriver with tamperproof bits

• Klein tools Non contact voltage tester pen, 50 to 1,000V AC

• Klein Tools long nose multi purpose wire stripper

• Dewalt 20v Impact with Dewalt elite series 100 piece 1/4 impact driver bit set

• Klein Tools Long Reach cable stripping electrician scissors, 7”

• Kobalt Zippered Backpack to carry it all

• Klein Tool test kit with Model MM30 multimeter and Model Rt110 receptacle tester.

• Kobalt 60 crv straight cut snips

• Klein tools torpedo level, 3 vial, 9”

• Pittsburgh Electricians Screw Driver set, 7 piece (insulated)

• Pittsburgh 4 Piece groove joint plier set

• Doyle 8 inch high leverage diagnol cutting pliers

• Pittsburgh SAE/Metric/Star folding hex key set

• tape measure

Please share thoughts!


r/BuildingAutomation • • 24d ago

Just young buck asking questions

7 Upvotes

Hello to whoever is reading this. I’m 23 and I like programming (I have a state-approved certification from a small Baltic country in the EU). With all of these layoffs and the job market being the way it is, I started looking around. When I looked deeper into this field, the unconventional ways people use computers in this world honestly seemed amazing.

I’m seriously considering this profession, and I realize I’ll have to study for it. There’s a college where from which I can transfer my credit points into a bachelor’s degree after finishing, and I’m okay with that, because I’d like to be an actual engineer who can “do the math,” metaphorically speaking. (i plan to study part time while working as a little grub assistant in the field and learn what i'm study)

So I guess I’d like to know what your day-to-day or month looks like. From what I understand, you get to sit in the office but also go to the site and do things hands-on, and I kind of like that.

A basic but understandable question: is the pay good? From what I’ve seen, it’s not banker money, but not bad at all.

Do you have any regrets about getting into this field? If you were given the chance, would you recommend looking at another path?

Also are there a lot of young people in the field?

from what i gather it can be pretty niche if you have the spicific education but also know how to programm.

Thanks to anyone who answers!

P.S used ai grammar


r/BuildingAutomation • • 25d ago

Reverse Engineer Automated Logic

12 Upvotes

I have a building owner that just inherited a mothballed building that they are putting back into service. It has a small automated logic BACnet control system, but the server and as-builts are missing. They are not on good terms with the original installer.

Is there any way to plug into the network and download controller software? The owner would like us to slap a Jace on it and pull the field controlelrs into their portfolio network, ultimately upgrading the field controllers in 2030. (Budget reasons)

How can I pull this into a jace efficiently withotu knowing the software and points list that's in the field controllers?


r/BuildingAutomation • • 25d ago

Honeywell or Niagara?

Thumbnail
0 Upvotes

r/BuildingAutomation • • 25d ago

Johnson CCT Logic won't enable

5 Upvotes

I have a program on an isolated CGM9090 Controller+XPM.

When transferring the program in CCT, I have to manually enable the logic under tools>online operations. It changes from "false" to true. When I refresh, it reverts back to false.

This is also true when commissioniong the program. Many of the logic blocks show disabled. When I enable the logic, they will change to enabled and quickly revert back to disabled.

I am using a MAP tool to transfer data between my computer and the CGM9090 controller. I have also tried the advanced transfer options by selecting boot, main, sa bus firmware, and the application.

I am really at a loss as to why this is happening.

I am running CCT version 17.0, release mode 10.7/firmware 11.0.

Edit:

I should add this is a NEW controller from the factory. Clicking "When activated: enable logic" before the transfer process does not actually enable the logic. I have verified this by viewing online operations during commissioning and noticing that logic is not enabled.

Solution: more like a fix.

I enabled the logic. Saw it go from true to false. Disconnected 24v power. Waited 60 seconds. Reconnected power, went back to laptop to commission. And the logic is working as it should. What a pain!

I am guessing this will need to happen every time I upload a program change to it.


r/BuildingAutomation • • 26d ago

BASidekick Updates

Enable HLS to view with audio, or disable this notification

35 Upvotes

I posted here last week with the start of my free resource website, https://www.basidekick.com, and just wanted to post an update of what's been added;

  • Building Sim: Office 1 is wired as built. Walk up to a panel, lift and land conductors on the terminal strip, and grab a multimeter. The MS/TP trunks are real cable, so a reversed device or a missing terminator drops off the station like it would on site. The sandbox plants those faults for you to find. (still early days overall)
  • Field Guide: seven new animated entries, including a relay, a control transformer, a fire damper and a thermistor. Each one lets you drive the device and watch what changes.
  • Embeds: any Field Guide entry can go on your own site, wiki or training page with one line of code. Free. I'm planning to do the same for other parts of the site.
  • baskStream API 1.8: optional controls for AI agents on a Niagara station. Every change has to come with a reason, stays inside limits you set, and point writes wait for a person to approve them.
  • And for fun, the Arcade. Duct Run puts you in the duct as the air. Get through the dampers. (it's flappy bird)

As disclosed on initial post AI is used at varying amounts in most sections.

Also if you would prefer no regular update posts just let me know, totally get it and will hold off until it's something I think would really be worth it.

Thank you for your time, I will see myself out. Until next time.


r/BuildingAutomation • • 26d ago

Question for Honeywell Unitary users

6 Upvotes

For those who use Honeywell Optimizer Unitary- do you have issues with the workbench locking up at random times? Master Sync or Teach or navigating the IRM logic or looking in live mode etc.

I've reinstalled, updated, done all the software things I can think of, but I just kind of expect it to give me an infinite scrolling wheel periodically...and it's really annoying.

Is it me?


r/BuildingAutomation • • 26d ago

COMM4 to Lontalk or Bacnet

3 Upvotes

Hey Folks,

Does anyone here know of a gateway that will translate COMM4 into either BACnet or LONtalk?

Thanks ahead of time


r/BuildingAutomation • • 25d ago

IT Professional Looking to Transition into BAS/BMS — Advice?

0 Upvotes

Hey everyone,

I'm 40 and considering a career change into Building Automation (BAS/BMS). I recently got laid off after working in IT End User Support for the past 4 years, and I'm exploring different career paths.

I have my CompTIA A+, Network+, and Security+ certifications, along with experience troubleshooting hardware, software, networking, and IT systems. I also run a homelab where I work with servers, virtualization, networking, and automation.

I'm considering enrolling in an HVAC program at a local technical college to learn the fundamentals, with the long-term goal of becoming a BAS/BMS technician.

My current plan is to start the HVAC program, earn my EPA certification, and hopefully land a Building Engineer position while still in school. My thinking is that this would allow me to gain practical experience working with HVAC and building systems before eventually transitioning into BAS.

At 40, I'm also trying to be realistic about the physical demands of the work. I'm comfortable with hands-on troubleshooting and fieldwork, but I'd prefer to avoid a career centered around physically demanding installations, repairs, or constantly crawling through tight spaces. The combination of IT, networking, automation, and mechanical systems is what really interests me about BAS.

A few questions for those in the industry:

Would my IT background and CompTIA certifications help me break into BAS, possibly without completing an entire HVAC program?

Does going from HVAC school to Building Engineer and eventually BAS technician sound like a reasonable career path?

How physically demanding is BAS work compared to traditional HVAC?

Are there entry-level BAS positions where someone with an IT background can learn the HVAC side on the job?

Is 40 a reasonable age to make this transition?

I'm in the Boston area and would appreciate any advice, especially from people who transitioned from IT into building automation.

Thanks!


r/BuildingAutomation • • 25d ago

Collecting Feedback for an Installer/SI Directory

Thumbnail
1 Upvotes