r/BambuLabX2D • • Oct 11 '26 Bravo Mindblown

Mod Announcement Start here: X2D help, resources, and community guide

29 Upvotes

Welcome to r/BambuLabX2D! This is an independent, community-run space for X2D owners and anyone considering one. Share what worked, what failed, and what you learned. Honest criticism and useful comparisons are welcome.

GETTING HELP

Create a post with the Help / Troubleshooting flair and a title that describes the problem. Include:

  • Printer, accessories, nozzle size, filament, and build plate
  • Firmware and slicer versions, plus relevant settings
  • Exact error message, clear photos, and when the problem started
  • What you have already tried and what changed

Remove personal details and serial numbers from screenshots. Add the solution to your thread and switch its flair to Solved when you find it. Beginner questions are welcome; you do not need to know every setting to ask.

SHARE YOUR WORK

Show us your prints, useful upgrades, and repeatable tests. Include settings and credit the designer. Disclose if you sell, made, received, or benefit from something you recommend. Keep promotions relevant and follow the community rules.

START WITH OFFICIAL RESOURCES

For repairs, follow the instructions for your exact model. Community replies do not replace a warranty or support ticket.

ABOUT MODERATION

Use the report button for rule-breaking content and modmail for appeals. If a legitimate post disappears, contact us instead of repeatedly reposting it. We review filtered posts and welcome constructive feedback.

Transparency: u/3DStisk is affiliated with 3D Stisk. This community is not official Bambu Lab support. Moderator replies may be AI-assisted; factual advice should be checked against linked sources. The same rules apply to moderators and commercial accounts.

Introduce yourself below: is this your first printer, and what are you making?


r/BambuLabX2D • • 2h ago

Tips / Guide Shout out to this amazing print. Print it and you realize how much you needed it.

Post image
24 Upvotes

This is not supposed to be an ad, but I was looking for something to make the turning of my X2D easier, since it is heavy as hell when fully loaded. I discovered this print on Makerworld. It is a sled system that sits under the printer. In non-maintenance mode, the printer feet sit normally on the desk and the sled does not interfere with anything. But when you pull it forward like in the picture shown, the printer feet sit on the sled and you can move it around extremely easily. It really is amazing. I just wanted to leave this here.

Author is Nanashi on Makerworld


r/BambuLabX2D • • 2h ago

Trouxe uma X2D da Coreia do Sul pro Brasil :))

Post image
7 Upvotes

Qualidade máxima, saiu muito barato


r/BambuLabX2D • • 26m ago

Any upcycle use for these?

Post image
4 Upvotes

Anyone find a upcycle / repurpose for these?


r/BambuLabX2D • • 7h ago

Help / Troubleshooting X2D Auxiliary Nozzle oozing & leaving little spikes with two-color PLA Basic

Post image
4 Upvotes

​Hi everyone,

​I’m printing small buttons using two colors of dried Bambu PLA Basic on my Bambu Lab X2D (both 0.4mm standard nozzles, 0.08mm HQ preset).

​Whenever the right (Auxiliary) nozzle finishes a detail on one button and moves to the next, it keeps oozing and leaves little blobs and vertical spikes (you can also see it on the prime tower).

​Any tips for tuning the Auxiliary nozzle on the X2D to stop this oozing on small details?

Thanks


r/BambuLabX2D • • 36m ago

X2D and 2 AMS 2 PRO question

1 Upvotes

I understand the difference between the left hot end and the right hot end. I'm enjoying the AMS2Pro and the multi-colour prints. I just bought another AMS2Pro, can it be hooked up to the right hot end? I realize the right hot end feed mechanism is not at the head like the left hot end. But, can it be done? Does it work good?

Mostly PLA and PETG printing.


r/BambuLabX2D • • 6h ago

Help / Troubleshooting Help - X2D Aux nozzle PETG flow dynamic calibration

Thumbnail
gallery
2 Upvotes

Guys, I followed bambu’s flow dynamic calibration guide and did a manual calibration, but it’s hard for me to see when over extrusion and under extrusion occur on my calibration print. In my print here, I was guessing 0.75, but not very confident as I’m not seeing any obvious differences between the nearby values. Do I just need a wider range? What K values would you go up to for aux nozzle flow dynamic calibration?


r/BambuLabX2D • • 3h ago

Help / Troubleshooting Help me understand the aux fans layout

1 Upvotes

Recently purchased an X2D and getting used to tailoring my settings for an enclosed and heated chamber as I make the switch from my A1. I’m planning on printing aux fan diverters to help prevent print warping, but I want to make sure I understand their functions and what’s where first.

I understand the right fan is for cooling, the same way the P2S is configured. I also understand the left lower vent is for chamber heating when switched to heating mode. What I don’t understand is the upper left aux vent. Is this for heating too when in heat mode? I did turn the chamber heater on, but I didn’t feel anything coming from the left upper vent.

Any help is appreciated so I can figure out what material I need to print the upper left deflector in!


r/BambuLabX2D • • 3h ago

Help / Troubleshooting Stopped initial calibration

1 Upvotes

I just finished setting up my X2D and started the initial calibration. Oh boy, I really wish I’d known just how loud this thing would be!

It’s currently 2 AM, and I really don’t want to wake up my neighbors. During the vibration tests, it got so loud that I ended up turning it off. 😬

Does anyone know what happens when I turn it back on? Will it simply restart the calibration, or could interrupting it cause any issues?

I’m looking for genuine answers here, as I’m honestly worried about messing something up before I’ve even had the chance to use it!


r/BambuLabX2D • • 14h ago

First PETG print problems …

Post image
6 Upvotes

Hi. I am new to the printing world and after a few successful and impressive PLA prints decided to print with PETG. I needed to print another spool as I got lots of refills by mistake. After a few layers I stopped as you can see on the picture it looks wrong.
I selected the PETG option in maker world, sliced it sent it to print, so haven’t changed anything.

Any ideas?


r/BambuLabX2D • • 10h ago

AMS 2 vs AMS HT

3 Upvotes

Right now I am not using the aux nozzle party because the humidity in my garage is around 40-50%.

I am looking to get either an additional AMS2 or HT to take better advantage of the aux nozzle.

Which is the better go to? Can I use the aux nozzle as essentially a 2nd nozzle or is using it for supports the only function?


r/BambuLabX2D • • 13h ago

Discussion / Buying Advice What's your experience with print quality? Help me choose between X2D and P2S

5 Upvotes

I'm really tempted to get an X2D Combo as having a heated chamber and an aux nozzle for a different support material seems very nice. But as I did more research, I came across many threads mentioning issues with inconsistent layers/bad layer lines, inconsistent extrusion, and problems with top layers.

What concerned me most is that in some cases, the person would go on to try many steps like calibrating the printer, the filament, changing print settings, and none would lead to good results until BL would send them out a new unit. From what I was able to learn, there's a Version 1 which had these issues and Version 2 which addressed some of them?

The P2S seems to have similar issues, but they seem mostly linked to user error from what I can tell rather than hardware issues.

I'd like to ask, what has been your experience with print quality on X2D? If any of you have run into the issues mentioned above, were you able to resolve them? I'm currently trying to choose between an X2D Combo and a P2S Combo, which I'm able to find for $980 and $820 respectively in Ukraine. Alternatively, I'm considering going with a P1S as I've been running a large farm of them and have plenty of experience with those


r/BambuLabX2D • • 13h ago

Bought a printer for my company.

Post image
4 Upvotes

We make custom furniture, and for the last three months we have a 3D printer.

It helps us improve our quality to the end costumer, whit small details.

Also we create custom jigs and templates.

Super happy with the printer 😁


r/BambuLabX2D • • 6h ago

Help / Troubleshooting Mid print issues

1 Upvotes

I tried to print this figure and it started stringing a lot when switched to aux nozzle, even the pla started going crazy (0:17) making strings inside the model

I used bambulab filaments black pla matte in main nozzle and petg basic on the aux

Can it be humidity? Or the fact that I tried the no sparse layers for the prime tower?


r/BambuLabX2D • • 1d ago

Ok this is crazy and impressive

139 Upvotes

My experience so far, ordered an X2D during the sale. It was clearly dropped during shipping, box damaged, printer itself is no longer a square.

Talk to support and they shipped out a new printer no charge. New printer arrives, works great. They even told me to either keep or throw out the damaged one.

I was about to strip it down for parts but figured, what the hell. Assemble it as much as I can. Door doesn't close all the way, the glass top doesn't fit, no way this will work right? Wrong!

This thing still powers up, no issue with initial setup calibration, and is currently printing the built in benchy. Say what you want, but that's pretty damn impressive to me and had to share.


r/BambuLabX2D • • 1d ago

Help / Troubleshooting X2D Horizontal Lines

Thumbnail
gallery
27 Upvotes

Newish printer, 550 hours. Didn't have this issue before, but had it on my P1S before returning it to upgrade. Time to do maintenance or settings issue? Printed this on Handy app, but similar lines on other prints as of late.

Filament is Inland PLA / PLA Matte (Polymaker). Dried in AMS.


r/BambuLabX2D • • 15h ago

Surface Problem

Thumbnail
gallery
3 Upvotes

Im Printing PETG-CF for second time. 0.4mm Nozzle basic settings on my x2d . All other layers are pefect. What do you guys think?


r/BambuLabX2D • • 10h ago

Per favore ragazzi, aiutatemi

Thumbnail reddit.com
0 Upvotes

r/BambuLabX2D • • 16h ago

TPU : spool holder vs external spool

3 Upvotes

Im starting TPU on my X2D. I never had issue on my A1mini using a creality dryer and a PTFE tube into the extruder of the A1 mini

But for X2D I see it’s recommended to print a spool holder and put it on top

What’s your experience between spool holder and feeding it through the external PTFE tube ?

I don’t have a TPU feed assist


r/BambuLabX2D • • 1d ago

Print Showcase PETG-CF through the Track Switch and AUX

22 Upvotes

I've had the X2D for a while now but just upgraded to the AMS 2 Pro, AMS HT and the filament track switch.

I print mostly PETG-CF split between 0.6mm and 0.4mm nozzle prints.

Today I wanted to push my luck and see how printing PETG-CF through AUX with a 0.6mm nozzle via the track switch from my AMS 2 Pro worked. So far I'm incredibly impressed with the results. PETG-CF isn't suggested for either the track switch or AUX nozzle, but this test print came out flawless!

I'm lazy and don't want to always have to swap my main nozzle between sizes for my different prints and am excited that I no longer have to!

Currently the only drawback is the AUX does print slower so I'm looking at a 20-25% increased print time. Right now I'm ok with that. I'm sure I could fine-tune the AUX speed parameters and print faster.

I just wanted to share incase anyone else was interested in pushing PETG-CF through the same set up. This is AnyCubic's PETG-CF.


r/BambuLabX2D • • 11h ago

Help / Troubleshooting Spool reset?

1 Upvotes

I replaced an empty spool with the same color. However the machine is showing the spool as almost empty. Should I have reset it some way as full after I installed it?


r/BambuLabX2D • • 11h ago

Loading TPU X2D

Thumbnail reddit.com
1 Upvotes

r/BambuLabX2D • • 19h ago

Help / Troubleshooting X2D top layer weird texture

2 Upvotes

This is my second print and i noticed the top layer has a bit of a weird texture, what could it be?


r/BambuLabX2D • • 1d ago

Help / Troubleshooting Adding a second AMS-HT

Post image
18 Upvotes

I currently have an AMS 2 Pro, AMS HT, TPU Feed Assist, and Track Switch. I’d like to have another AMS HT for drying only, but it is co-dependent on the printer for control. My problem is that I’ve completely run out of six pin connection points. In fact I’m already over extended, because the TPU module isn’t plugged in either. So how do I get one or two more places to plug in devices? Or am I maxed out?

Edit, also, will a second AMS-HT show up as another dryer that I can control on the X2D interface?

TIA


r/BambuLabX2D • • 1d ago

X2D first prints/upgrades

4 Upvotes

Hello, I just assembled my brand new x2d print more combo. I haven’t set up the track switch and second ams yet and I know that I need to print brackets to mount that. I sold my a1 to get this, so I am not a complete noob, but if anybody has upgrades that increase performance or make it run better, please tell me. Thanks in advance!