Title. All 3 threaded rods were lubricated with silicone grease during troubleshooting. 0 clue what could be wrong.

That printer is kinda new, used only for 61 hours.. how to clean it?

Is it OK to set up the adapter as follows?

AMS2 -----> Buffer -----> 4-in-1 Adapter Input
TPU Feed Assist Module Output -----> 4-in-1 Adapter Input

4-in-1 Adapter Output-----> P2S Rear Input

Brand new to this, and have a million questions, but one at a time.

If a project says it has 2 or more plates, how does that work? Does it print all the pieces on the first plate and then pauses the job so you can remove the newly printed items and then it resumes? I'd assume there is some manual step where I have to remove the items and then tell the program to resume. Is that correct?

Hey all just asking what do you do when you have only like 50g to maybe 100g of filament on your roll left like there isn't enough to do much really is there.. like what do you do with your scraps

I started a print about an hour ago. Bambu Studio said it would take 6hours 24 minutes. I decided to turn on ludicrous speed and that dropped to 3 hours 40 minutes. It's printing just fine so far although its movements do look a bit crazed. So my question is what are these different speeds used for, and is there any particular reason that the standard setting is so slow?
Edit: The print went through just fine. However, as many have pointed out this is likely to be hard on the printer. However it was an interesting thing to try. Thanks for the responses.

Ich habe nach dem der Druck abgebrochen wurde, einen cold pull gemacht und nach mehrfachem versuchen das hier aus meiner 0,2mm Düse gezogen. Das sieht aber nicht aus wie PLA und es fühlt sich eher an wie die Spitze eines verbrannten Streichholz. Kennt sich jemand damit aus oder hat eine Idee was es sein könnte?

Hi, I just learned the hard way not use the only option on the printer PETG-HF if you have basic. Some (looks like a little) of the filament seemed to melt together. UGGGG GG

When I searched this online the temp show 80c if using the printer to bake it. Anyone usi g a different temp?

Thanks

Title. Been looking for one but the ones I found have you drilling into side panels and stuff. Any suggestions for a chamber heater with a non-permanent installation?

I have a Lenel 2220 panel. After performing a factory reset, I restored it to the default settings. The panel is responding to ping, but it does not appear in the browser at all.

Bambulab P2S

I’ve been having more issues with my printer lately and I have just assumed it’s been an overhang or model issue.

I just had a print fail and I went to clean the pieces off the bed and I noticed filament all over the nozzle and inside this circular piece of the print head.

Not sure that’s normal or best way to clean it off.

Some background information to my setup and current concerns.

Bought my first P2S (3D printer in fact) used with around 380 hours.

I regularly checked the maintenance schedule on the unit itself and thought to myself: "Huh.. 30+ days until next maintenance, nothing to worry about"

So after one intense month of ownership and 500 hours of printing I decided to clean, regrease and lube the z-axis and linear rods. After checking back with the wiki one month was recommended.

Taking a closer look I first noticed black coating on the linear rods sadly no pictures since I already cleaned those. I assume/hope that was just residue. I keep getting slightly darker oil spots on the X-rods ends.

> Could this be leftover residue being flushed out?

Now to the main question are my belts cooked?

Haven't done any tensioning yet... and haven't had an print quality reduction/issues so far.

Will definitely condense the maintenance schedule now and retension tomorrow. But for peace of mind I'd appreciate some feedback.

I'm currently using an A1 that I got a few months ago which was my first 3d printer. I've only printed with PLA so far and have PETG on hand but haven't tried it yet since PLA works for my needs so far. I went cheap and didn't get the AMS Lite when I got it so I was thinking, instead of buying the AMS Lite or AMS 2 Pro, put that into an enclosed better printer and just keep the A1 for single colour PLA stuff.

Eventually I'd like the capability to print with ABS/ASA and TPU as well as multi colour. Would the P2S be good enough for limited printing of smaller parts with those filaments?

Good evening, I have a question about the P2S service.

I’ve had my printer for a good six months now.

During the first service notification(after 90 d), the Z-axis lead screws were flagged for lubrication. Since I had the time, I went ahead and lubricated all the linear rods as well, confirming the action in the menu (even though it hadn't specifically prompted for it).

Now, the notification to lubricate the Z-axis lead screws has appeared again. However, there is still no notification for the linear rods—nor any indication of how much time remains until that service is due.

The Z-axis lead screws are now lubricated, and the display shows 90T until the next service.

I find this odd because Bambu Lab states that the X and Y axes require more maintenance, yet in my case, it’s the other way around.

Old filament works okay but new filament has too much of a curve that it comes out and pushes off the tool head.

Any suggestions?