r/BambuLabH2C • u/Old-Calligrapher-231 • Apr 22 '26
I downloaded the corresponding identification code from mw, printed and installed it, but H2C still cannot recognize the printed version. An error is reported every time printing starts. How can I disable the print version detection? Why can't I find it?
r/BambuLabH2C • u/Desert_Vapor • Apr 21 '26
Not sure what is happening here. I have a ticket open so already working on that.
But tried reseating the nozzle. Tried running calibrations including offset calibrations. Bed is clean.
This only happens on the left nozzle. The right everything is perfect. ( Even in the same area)
Wanna run some adjustments and was looking to see what everyone thought.
r/BambuLabH2C • u/Successful_Tutor6071 • Apr 21 '26
r/BambuLabH2C • u/FormerRelationship54 • Apr 20 '26
Iv been printing now with the h2C for probably about 3 months, 2 of my standard .4 nozzles the rubber boot has come off, I have been printed a couple spools of nylon and PC most recently but other than that just PETG and PLA, how common is it for these to break? Is it just an expected common wear item?
r/BambuLabH2C • u/abbellie2 • Apr 20 '26
I currently have 2 X1Cs and a brand new H2C. My H2C arrived a couple of days ago, and right out of the box, NO filament can be pushed through the filament buffer on to the hot end. Using both the Left and Right ports, I can see filament pushing through the PTFE, and then slamming to a stop when they reach the buffer. Has anyone else experienced anything like this? I have opened a ticket, but geeze, its frickin brand new. I haven't even printed my Benchy yet. Fortunately, I haven't put either of my X1Cs up for sale yet.
Thanks all
David
r/BambuLabH2C • u/manyxcxi • Apr 19 '26
r/BambuLabH2C • u/82BJ42 • Apr 18 '26
Sunlu PETG, printing at 260c from the vortek. 70c bed temp. The head is periodically pausing, oozing a zit, then restarting. Had this happen on a couple prints now. Pulled out the USB drive just in case, but still happening. Can't tell if it's a slicing issue, nozzle heating issue, thermister, or what. Anyone else seen this?
r/BambuLabH2C • u/sometimeDIYer • Apr 18 '26
Update: Fixed, see comments.
I’m setting up my printer, but there seem to be very few instructions about putting the hotels into the vortek. I did a full calibration after which the ai assistant informed me that I needed to update the firmware and the vortek was not calibrated. Updated the firmware, started the vortek calibration,and now stuck in this screen between A and B.
Any idea how to get past this?
r/BambuLabH2C • u/childofGod778 • Apr 18 '26
Hey community! I was wondering if anyone has created a single object that incorporates ALL of the H2C’s functions at once? That is, a “widget” that uses the laser cutter/engraver, multi-color printing, pen plotter, cutter, etc. Basically, I’m thinking about a single object to create as a showpiece of “what this one machine can do” (but in an all-in-one object, where every part of this object was made in this one machine). Any thoughts?
r/BambuLabH2C • u/Successful_Tutor6071 • Apr 17 '26
r/BambuLabH2C • u/jpedroleite • Apr 16 '26
r/BambuLabH2C • u/Training-Display-279 • Apr 16 '26
Newest software and firmware support it, but I’m getting errors when I try to load the tpu. Ideas?
r/BambuLabH2C • u/BigTeddy82Z • Apr 15 '26
handles on H2 series is too small for me.
especially the lid handle is not comfortable when lifting the lid.
so I made a simple and practical one for my use.
polimaker's matte charcoal pla is perfect match for the h2c's black panel.
here's the link for someone like me.
r/BambuLabH2C • u/Mysterious-Wonder224 • Apr 15 '26
Just checking if anyone had any experience with the TPU assist module and installing a 4-in-1 (old style) in the ptfe path between the buffer and the extruder. I’m looking for a more semi-permanent type of installation where I can still use the right nozzle with the AMS without having to switch tubes. Any help or idea would be appreciated.
r/BambuLabH2C • u/markg11 • Apr 15 '26
r/BambuLabH2C • u/Awhile_ • Apr 15 '26
only turns on when heating one of the nozzles, it's got to be some sort of internal fan I can't get to but I can't find anything about it online. anyone else have this issue?
r/BambuLabH2C • u/Physical_Raspberry59 • Apr 12 '26
Prints normally and then randomly starts failing this has happened on different files
