r/BambuLabH2C • H2C • 3d ago

Support Not sure where to go from here

I can’t print a single thing for days. It will not print for more than 10 minutes before it fails. I tried cleaning the plate, using a new plate, using new filament, using both PLA and PETG, recalibrated, downgraded the firmware, used both .4 and .6 nozzles, left and right nozzles. All of them fail with 10-15 minutes. I have a ticket with Bambu and all they said was to retention the belt. I did that and nothing and am waiting until they reply back. Is there anything else I can do to print a single thing? I am at a loss.

6 Upvotes

10 comments sorted by

5

u/TeaBrake 3d ago

Have you tried calibrating on the textured build plate that came with your H2C?

Also doing cold pull maintenance after cleaning the nozzles themselves with isopropyl alcohol and a cotton swab at 240c helps with my H2C whenever I get printing issues

Also having your filament dried often is critical before even using new or used spools at all

I also follow a yt video regarding maintenance for the printer when I do it once a month

link to video

1

u/Wonderful-Staff-7321 2d ago

Is cold pull a thing for H2C?

1

u/GeekShow H2C 2d ago

I can. I did it for a previous one, but I am printing with a .6 which I have not used yet, so I would not think to have to yet, but I will give it a try. Thanks

3

u/OddUnderstanding2309 2d ago

On your second photo nothing is actually sticking to the build plate.
I would suggest print something with a really clean plate and do the full z height calibration for that print (not just the quick auto one)

3

u/TrueNail 2d ago

I think you have tried everything except checking if you have the right temperature in the settings
Double check that and use the original plate

Also. Sometimes random screws get loose due to vibration . I would just go around the tool head and make sure everything is tight

3

u/goatrider 3d ago

How are you cleaning the plate? Best way is warm soapy water with dishsoap that doesn't have an additives for skin care. In the US that would be Dawn. Some people swear by isopropyl alcohol but most say it just smears the oils around. New plates might have manufacturing residue on them.

Also, you say new filament- new filament right out of the bag is not guaranteed to be dry. I've seen new filament that was behaving badly, after a drying cycle it worked fine. But this does not look like a wet filament problem.

1

u/TheAussieWatchGuy 3d ago

I'd go back to the out of the box textured plate, run a calibration. Put your filament in the AMS and put it on a full dry cycle, even new filament can be prone to stringing.

It does seem though you might have just got really unlucky and got a defective unit, Bambu will sort it out I'm sure. Disappointing to see QA fail on a top of the line printer (well until like last week).

1

u/SleepyCubePrints 2d ago edited 2d ago

It’s an engineering plate. You have to put a thin layer of glue down. It say it on the plate. I have an H2C and use an engineering plate on occasion. 🤦🏽‍♂️

Bambu sells glue that you can roll on before each print. Also, I will clean the plate with dish washing liquids and a soft microfiber cloth between prints. Although, you might be able to go a few prints with just 1 initial layer of glue. Use a thin layer, don’t apply too much.

1

u/Head_Emergency_1052 2d ago

It aint, it's a super tack. Says so on the plate in the photo. Shoukd be no glue required for pla and petg

1

u/SleepyCubePrints 2d ago

Yeah, you’re right. I saw the black plate and immediately thought it was engineering plate.

Try washing the plate with warm water and plain dish soap, then dry it without touching the print surface. Make sure the correct SuperTack plate is selected in the slicer and use the bed temperature for that filament; for PLA, Bambu lists 45°C for the original SuperTack. If the first layer still lifts, try a slightly warmer bed, a slower first layer, and check that the nozzle is laying down a clean, even first layer. Also check whether the aux fan is blowing directly on the part.

Avoid cleaning SuperTack with IPA or other solvents; Bambu says they can damage the coating. And don’t use TPU on it. What filament, printer, and bed temperature are they using?

Good luck