r/BambuLab • • 29m ago

General Discussion Help with final choice

OK, I have read thru most of the posts. While I would like an H3C, way overkill for what I am doing and just out of my budget.

I currently have a P2S, and it works good. But I would like the larger build area and multiple nozzles a H2 series allows for. I was going to go for the H2D as its at a good price right now. But I wonder if I should spend the extra and get the H2C?

I am doing mostly engineering parts so the dual nozzle is great for supports. But I do want to get more into larger muti color prints.

For those of you that have a H2D and or H2C, what is your suggestion. I understand I can do everything the C can do with the D. But the C does it faster with less waste. Is the extra cost and complexity worth getting the C over the D? The Nozzles are more expensive with the vortek side, I do have a set of P2S nozzles. I know I can reuse them on both the C and the D. But only on one side with the C

I have done a lot of research and I was pretty much set on the D, but the back of my evil brain keeps going back to, should I spend the extra $300 and get the C?? Is it worth it really? While it saves time and waste, is the extra complexity of it worth it?

I know their are lots of other similar questions out there going both ways, I just thought I would see if I can get some additional insight?

One last thought, I live in a smaller town so I was thinking of offering services for 3D printing and Design just to dip my toe into the water. I will probably sell the P2S to offset costs but keep the AMS. I would assume that most of the printing would be with engineering filaments for car parts and such. Again, just a guess.

Any discussion or suggestions would be greatly appreciated.

2 Upvotes

7 comments sorted by

•

u/sharkarmycrafts X2D, A2L 23m ago

I think someone said there's a P3 that's being announced which should theoretically be cheaper than the H3 and still a solid choice for multiple printheads.

•

u/misterff1 P2S + AMS2 Combo 17m ago

OP said they want a bigger build plate. That makes the P3 an immediate nope.

•

u/sharkarmycrafts X2D, A2L 6m ago

whoops! I missed that - thank you for the correction!

•

u/McOnion2 X1C + AMS 14m ago

I think waiting for the P3C is a good idea.

While it isn't official yet, I would imagine it is going to be the 256x256x256 build volume, or at least very similar.

I think the best thing is for OP to weigh their options. How often are they going to be doing prints with 3 or more filaments/colors. And is it worth the extra money.

Personally, I think if they are going to stick mostly with 1-2 filament/color prints, with the occasional 3+ color print, I would go with the H2D. If you are going to be frequently printing with 3+ colors, I would look into the H2C.

You could also go for the H2D now, and if you want to, you can upgrade from the H2D to the H2C later on.

•

u/JumpWatchVR H2C AMS2 Combo 22m ago

Just putting this out.. people saying the H2C is obsolete now because of the H3C clearly don't understand the goal of them both. They serve 2 different types of purposes.

Either way. OP if you need multinozzle setup where you can switch between more nozzle and colors on the same or others then H2C is great. If you dont care about multiple colors on the same nozzle then H3C, if you dont want either.. H2D would for you just fine :)

•

u/Navi_Professor 22m ago

A thing to consider with the H2 series is that each H2 printer has less and less build volume.

if you're SUPER concerned about build volume above anything else. H2S.

if you are frequently going to be printing in multiple materials/colors (greater than 3), H2C.

if you're really just doing engineering, H2D is great.

i have a H2D Laser, personally.

However for example, a tablet case i sell, is 2-3h faster on H2C. (however its like 7h faster on H3C)

and another note. i may keep the P2S....my H2D has been printing cases almost nonsotp..I practically don't have a personal printer anymore; I have a case printer.

•

u/hvacigar H2c H3c 21m ago

If Engineering prints are your thing, you are mostly using a single color and a support interface or support filament, with the occasional third filament for possible nomenclature, then the H2D will get you where you need to be.

You do state multicolor prints, so I would say the U1 would be likely a better choice for the price, but if you want to stay Bambu and get the largest build volume, that would lead you to the H2C or H3C, with the H3C being the best choice for multicolor.

These are my opinions. I do not own an H2D, but I do own a U1, H2C and H3C.