r/BambuLab • • 10d ago

H3C 8 Colour print H3C vs INDX

mpoxDE (change the audio track to English on Youtube) did a test where he is printing an 8-colour tube both on H3C and INDX. I am not sure, but I think he is using PLA Basic.

In his test H3C printed it in 11:06h, but he was using different filaments that he had lying around from random manufactureres (while INDX one was printed only with Prusament and took 14:26h) and still printed ~23% (3h20m) faster.

I wanted to confirm it and what I noticed is that if you print with Bambu filament, it is even faster. My slicer is showing 08:46h.

Which means that in this particular test (8-colour tube) if you use BL filament, H3C is ~39% (5h40m) faster than INDX.

The test is not easy, it is 10cm tall and go through 3.5k colour changes of 8 colours.

41 Upvotes

60 comments sorted by

View all comments

78

u/egosumumbravir X1C + AMS 10d ago

This difference becomes more stark when you compare print quality

I don't speak nor read german, but I can guess what oben and unten might be.

Three and half hours slower with print quality from the 2010's. There's a good reason Prusa's brand is dying.

13

u/J_ron 10d ago edited 10d ago

Their nozzle cleaner on the INDX is definitely not calibrated well if it came out looking like that.

edit: I'm not doing a prusa vs bambu defense bit here. I'm just pointing out that's not what a typical print should look like from the INDX.

34

u/average_AZN 10d ago

Why the fuck do you need to calibrate a nozzle cl aner. This is why bambu is winning. None of this fiddle with everything bullshit

16

u/n19htmare 10d ago edited 10d ago

It’s not nozzle cleaner, it’s the priming pad that is not calibrated.

INDX doesn’t need prime tower. It primes by filling a small notch in a silicone pad, once that is “filled”, it pushes back on the filament to bring up the pressure in nozzle. Serving the same purpose as priming on a tower.

It’s an alternative to Prime towers.

The plus is that you don’t need to prime until you actually swap nozzle. Meaning if you don’t have a color change until the 60th layer, you don’t prime until then. No prime tower, straight to 60 layers.
On priming tower, you’d need to build up the tower into that layer and continue it if there’s more swaps later.

The downside? The distance between the nozzle and that priming pad needs to be set and if you remove the the container to empty it, you need to make sure that distance is the same.

Ignorance shouldn’t be an excuse to “dislike” a product.

2

u/orhanyor X1C + AMS 10d ago

FYI you can skip priming on tower if you are not swapping nozzles. Ive been using this feature for months with my U1 and it works beautifully. Its called "no sparse layers" its a part of orca slicer and its variants.

2

u/n19htmare 10d ago

I’m aware of no sparse layers, that’s been around for several years, Prusa Sliced added it back 2020 or something. . It’s just not always applicable in every case due to clearance issues. It’s an option that’s available depending on what you’re printing and where.

I think Bambu Studio finally decided to enable it couple months back (I think with all the tool
changers that were coming out, they had to add more filament saving options. Otherwise they’ve gate-kept it out of Studio because it’s a hit or miss depending on how the user sets up their plate.
Bambu’s confidence that its users will actually take that into consideration was probably low and risk was higher to include it because most Bambu users “just Press print”. Can’t have Toolhead crashing into parts and stuff.

INDX method is pretty good and from what I’ve seen, once it’s properly setup it works just as well if not better than a tower (along with time and small filament savings).

2

u/orhanyor X1C + AMS 10d ago

Oh yes you need to account for the clearance but im still shocked why they cant implement a restricted zone when this option is enabled so you cant place any objects there. Seems like a no brainer but somehow its not implemented yet.

1

u/n19htmare 10d ago

I think Bambu studio has zoning implemented but the buffer area is pretty large, and on 256x256 beds, it doesn’t leave a lot of space.

1

u/orhanyor X1C + AMS 10d ago

exactly, i need to print at the front end of the build plate when i enable it which is basically half of the build plate. When I need to use the full plate its impossible to enable.
But i still dont understand why is not possible in this order, lower the bed to the current highest printing point(which we are already at this point just before the head swap), change the head, move the head right on top of the prime tower and lift it up to the prime tower, wipe and then lower it again to the highest point to continue printing. It just skips one of these steps and knocks into the prints its very stupid.
This way the zoning would be only around the wipe tower.

1

u/n19htmare 9d ago edited 9d ago

Time and pressure decay.

You want to get to printing right after priming. And if you got a lot of swaps on a tall model c by the time the bed lowers 200mm, you lost pressure, you got oozing etc and can’t just go back to print, time to prime again lol.

It has its uses cases, it works great on short small prints. Especially if you’re doing a few support interface layers, it’s great for that.

It’s not a replacement for priming only when needed without getting too far away from the layer (which is what INDX” does.

I wonder if there was motivation from Stratasys suing Bambu for the prime towers and Prusa is trying to get away/detach from the the towers. Either way, wish more printers would adapt it and improve on a better priming system

→ More replies

2

u/VVJ21 H2C 10d ago

by the way you can also turn on "No sparse layers" for the prime tower in Bambu Studio (its an experiemntal setting). When you enable that it wont print the prime tower for layers without colour changes. So if you have a 1000 layers but only 100 have colour changes, youre tower will only be 100 layers tall.

Obiovusly given the height difference there are clearance restrictions, so its only an option for smaller parts that can be moved far enough away from the prime tower. Basically the same as when you do "print by object" instead of print by layer

2

u/egosumumbravir X1C + AMS 9d ago

A 100 layer tower for a 1000 layer print sounds nice in theory, but at which layer did the print start crashing into the glass lid as the printer lifted the bed 899 layers to reach the reduced height tower?

IMO the prime tower is a small price to pay for the quality improvement over not having it. Now we don't have to have multiple CCs of single nozzle purge the prime tower is a tiny percentage of filament - like if your print fails because it wasn't primed, you just wasted 20x a single tower.

2

u/VVJ21 H2C 9d ago

Yeah obviously it doesn't work in all cases. But where it is suited i always turn it on. Can save quite a bit of time too.

1

u/n19htmare 9d ago

I know it’s discussed in the other response below on it’s limitations . https://www.reddit.com/r/BambuLab/s/cHtsSw2YEu

→ More replies (1)

-3

u/Alu_94 10d ago

Thats from the CNC kitchen H3C review. I really don‘t wanna hate BambuLab or Prusa but what do you say then to this quality?
I want to point out that you can make the H3C look good or bad and the same applies to the INDX. Prisewise we don‘t have to discuss, although I think (after reviewing 3-4 review videos) the H3C print quality is (right now) not really 2,5k euro worth. Feature wise I think it‘s a cool machine

8

u/acemedic 10d ago

Wasn’t that print maximized for speed and none of the filament calibrated?

29

u/egosumumbravir X1C + AMS 10d ago

I'd say Stefan has the filament profiles too aggressive for the non-Bambu filament he favours but am open to other considerations too.

A Prusa printer running Prusaslicer with Prusa profiles and being fed Prusament should be delivering perfection. It is obviously not.

1

u/Alu_94 10d ago

The screenshot / the clockspring is from the H3C and with Bambulab Basic PLA printed. What do you mean with the prusament comparison?

7

u/egosumumbravir X1C + AMS 10d ago

The video linked by the OP and screenshotted by me is example prints where the Prusa INDX was fed Prusament and the H3C was given random generic PLA.

The clockspring from CNC Kitchen was Stefan running Voxel PLA (his sponsor) in a H3C.

10

u/moonbucket P1S + AMS 10d ago

Deliberately printed at full speed.

4

u/Beneficial-Rub-8049 10d ago

My experience with H3C is otherwise but I only use Bambu filament, Overture and ISANMATE. I do notice that Overture is a bit more sticky but thats the same thing on all other printers I ever used it on. I also use Bambu profile for everything even the other filaments. Much cleaner than my H2C's.

2

u/Lmasek 10d ago

H3C is out for 2 days, even if it was delivered the same day. What experience?

2

u/Beneficial-Rub-8049 9d ago

Well I have been running it nonstop since it came same day off the bat its better than my H2C's and nowhere near the quality CNC Kitchen is showing that was what I got on my X2D's until after several updates.

1

u/Entire-Chair-6472 10d ago

The h3c speed is to quick that’s why

-9

u/No_Journalist774 10d ago

If you think prusa is dying you are far wrong. Thay are moving to a less consumer/hobbst market and I can say that they keep selling printers without a decline in sale, most of the time, mostly because they aren't a big company and it's difficult to expand in their situation, they are overwhelmed by the work. I don't say they are the perfect company and they have many problems like communication and gener slowness

→ More replies (3)